Research on high strength and creep behavior of in-situ (Al2O3 + ZrB2)/7055 Al nanocomposites
Source abstract
Abstract
In this study, to achieve high strength, high ductility and good creep resistance, in-situ Al 2O 3 and ZrB 2 nanoparticles were introduced into 7055 aluminum alloy subjected to the deformation of hot rolling. The interface between nanoparticles and Al matrix displayed tightly-bonded and there were orientation relationships (ORs) between them: 1 ¯ 2 ¯ 4 ¯ Al 2 O 3 / / 2 ¯ 1 ¯ 1 ¯ Al ,(021) _{Al2O3}//(111) Al, 020 ZrB 2 / / 02 2 ¯ Al . The precipitates were easy to nucleate at the interface than in the matrix due to the low energy barrier to overcome. Precipitates like η and Al 2Cu had the ORs with the matrix: 11 2 ¯ 3 η / / 1 1 ¯ 0 Al , [111] _{Al2Cu}//[110] Al. The nanoparticles along with the precipitates had the effect of both promotion and inhibition to the recrystallization process. The particle-induced improvement for the strength was due to the excellent work-hardening ability. Moreover, mechanical performance of the (Al 2O 3 + ZrB 2)/7055 Al nanocomposites exhibited the tensile strength of 749 MPa and the elongation of 21.81%, which indicated 14.3% and 11.8% higher than the matrix. The plastic zone and dislocation punched zone of the nanoparticles had been calculated during the crack process. The Al 2O 3 and ZrB 2 nanoparticles indicated the high-temperature creep resistance ability with the steady creep rate of the (Al 2O 3 + ZrB 2)/7055 Al composites 6– 17 times higher than the matrix, in which the values of apparent stress exponent (n), apparent activation energy (Q) and threshold stress were 9.48, 374.13 kJ/mol and 50.13 MPa, respectively. The stress exponent of 5 suggested that the dislocation climb was dominative in creep process. In addition, the strengthening contributions, toughness mechanism and creep behavior were discussed.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Synergistic effects of γ-Al2O3 nanoparticles and fast cooling on the microstructural evolution and mechanical properties of Al-20Si alloys10.1016/j.matchar.2021.111240 ↗
2. Multistage aging treatment influenced precipitate characteristics improve mechanical and corrosion properties in powder hot-extruded 7055 Al alloy10.1016/j.matchar.2020.110683 ↗
3. Dynamic recovery and recrystallization mechanisms in secondary B2 phase and austenite matrix during hot deformation of Fe–Mn–Al–C-(Ni) based austenitic low-density steels10.1016/j.msea.2022.143095 ↗
4. The improved mechanical properties of Al matrix composites reinforced with oriented β-Si3N4 whisker10.1016/j.jmst.2019.02.003 ↗
5. Interface formation and bonding control in high-volume-fraction (TiC+TiB2)/Al composites and their roles in enhancing properties10.1016/j.compositesb.2021.108605 ↗
6. Effectively enhanced load transfer by interfacial reactions in multi-walled carbon nanotube reinforced Al matrix composites10.1016/j.actamat.2016.12.022 ↗
7. In-situ Al2O3-Al interface contribution towards the strength-ductility synergy of Al-CuO composite fabricated by solid-state reactive sintering10.1016/j.scriptamat.2021.113825 ↗
8. Spark plasma sintering mechanisms of the Al-Zn-Mg-Cu alloys and TiB2/Al-Zn-Mg-Cu composites10.1016/j.matchar.2020.110825 ↗
9. Mechanism of deformation and development of rolling textures in polycrystalline FCC metals. I. Description of rolling texture development in homogeneous CuZn alloys10.1016/0001-6160(88)90172-1 ↗
10. Cold rolling texture evolution of TiB2 particle reinforced Al-based composites by Neutron Diffraction and EBSD analysis10.1016/j.matchar.2017.12.028 ↗
11. Dynamic recrystallization behavior and mechanical properties of bimodal scale Al2O3 reinforced AZ31 composites by soild state synthesis10.1016/j.jma.2020.02.012 ↗
12. Cavitation-resistant intergranular precipitates enhance creep performance of θ’-strengthened Al-cu based alloys10.1016/j.actamat.2022.117788 ↗
13. Effect of stress and temperature on creep behavior of a (TiB + TiC + Y2O3)/α-Ti composite10.1016/j.matchar.2021.111495 ↗
14. A creep-resistant additively manufactured Al-Ce-Ni-Mn alloy10.1016/j.actamat.2022.117699 ↗
15. Microstructure and properties of 6111Al matrix composites reinforced by the cooperation of in situ ZrB2 particles and Y10.1016/j.jallcom.2020.154624 ↗
16. Microstructure and high-temperature creep properties of ultrasonic in-situ nano-A12O3/6063Al composites
17. The influence of interface shear strength on the glide dislocation–interface interactions10.1016/j.actamat.2011.01.056 ↗
18. Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction10.1016/j.actamat.2020.116524 ↗
19. The effects of in-situ ZrB2 particles and Gd on the solidification behavior and mechanical properties of AA6111 matrix composites10.1016/j.jmrt.2021.08.025 ↗
20. A critical review: crystal structure, evolution and interaction mechanism with dislocations of nano precipitates in Al-Li alloys10.1016/j.matdes.2022.110629 ↗
21. Imaging of arsenic Cottrell atmospheres around silicon defects by three-dimensional atom probe tomography10.1126/science.1145428 ↗
22. Flow behavior and dynamic recrystallization mechanism of A5083 aluminum alloys with different initial microstructures during hot compression10.1016/j.msea.2020.139522 ↗
23. Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al–Zn–mg–cu matrix composite10.1016/j.actamat.2019.11.068 ↗
24. Influence of multi-microstructural alterations on tensile property inhomogeneity of 7055 aluminum alloy medium thick plate10.1016/j.matchar.2016.01.020 ↗
25. A new powder metallurgy routine to fabricate TiB2/Al-Zn-mg-cu nanocomposites based on composite powders with pre-embedded nanoparticles10.1016/j.mtla.2019.100458 ↗
26. Strength and ductility improvement of an in-situ TiB2/Al-Zn-Mg-Cu composite by elliptical cross-section torsion extrusion10.1016/j.compositesb.2021.108843 ↗
27. Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles10.1016/j.msea.2021.140852 ↗
28. Precipitation behavior and mechanical properties of Al-Zn-mg-cu matrix nanocomposites: effects of SiC nanoparticles addition and heat treatment10.1016/j.matchar.2020.110827 ↗
29. Effect of TiC/TiC-TiB2 on microstructure and mechanical properties of spray formed 7055 aluminum alloy TIG welded joints10.1016/j.jmrt.2021.08.146 ↗
30. Microstructure, tensile and compression behaviour of B4C particles reinforced Al7075 matrix composites
31. Microstructure, mechanical properties and fracture mechanisms of ZrB2 ceramic reinforced A7075 composites fabricated by stir casting
32. Effect of ZrB2 on microstructural, mechanical and corrosion behaviour of aluminium (AA7178) alloy matrix composite prepared by the stir casting route10.1016/j.ceramint.2021.01.158 ↗
33. Effects of nano-sized TiB2 particles and Al3Zr dispersoids on microstructure and mechanical properties of Al-Zn-mg-cu based materials10.1016/S1003-6326(21)65648-0 ↗
34. Dual beam laser fusion-brazed Ti6Al4V/AA7075 dissimilar lap joint: crack inhibition via inoculation with TiC nanoparticles10.1016/j.matchar.2022.112127 ↗
35. Achieving simultaneously improved tensile strength and ductility of a nano-TiB2/AlSi10Mg composite produced by cold spray Addit Manuf10.1016/j.compositesb.2020.108404 ↗
36. Breakdown of the hall-Petch relationship in extremely fine nanograined body-centered cubic Mo alloys10.1016/j.actamat.2021.116950 ↗
37. Synergistic strengthening and toughening of copper coated graphene nanoplates and in situ nanoparticles reinforced AA6111 composites10.1016/j.msea.2021.141661 ↗
38. Strengthening in carbon nanotube/aluminium (CNT/Al) composites10.1016/j.scriptamat.2005.07.022 ↗
39. Strengthening mechanisms in carbon nanotube-reinforced aluminum composites10.1016/j.carbon.2015.08.112 ↗
40. Strengthening mechanisms and modelling of mechanical properties of submicron-TiB2 particulate reinforced Al 7075 metal matrix composites10.1016/j.msea.2021.141873 ↗
41. Multiple gradient structures driving higher tensile strength and good capacity to absorbed energy in aluminum wire processed by cryogenic pre-torsion10.1016/j.scriptamat.2021.114436 ↗
42. Low thermal expansion coefficient and high thermal conductivity epoxy/Al2O3/T-ZnOw composites with dual-scale interpenetrating network structure10.1016/j.compositesa.2020.105993 ↗
43. RETRACTED: study on the antioxidation properties and mechanisms of SiC/Si–ZrB2–CrSi2/SiC multilayer coating related to strain compatibility and stress distribution via XRD and Raman spectra10.1016/j.compositesb.2021.109452 ↗
44. Strengthening mechanism of B4C@APC/Al matrix composites reinforced with bimodal-sized particles prepared by hydrothermal carbonized deposition on chips10.1016/j.jmst.2022.01.012 ↗
45. Strengthening mechanisms in direct metal laser sintered AlSi10Mg: comparison between virgin and recycled powders
46. Strengthening and toughening mechanisms of Mg matrix composites reinforced with specific spatial arrangement of in-situ TiB2 nanoparticles10.1016/j.compositesb.2020.108174 ↗
47. Nanostructured high-strength molybdenum alloys with unprecedented tensile ductility10.1038/nmat3544 ↗
48. Bioinspired structural materials10.1038/nmat4089 ↗
49. Toughening of aluminum matrix nanocomposites via spatial arrays of boron carbide spherical nanoparticles10.1016/j.actamat.2015.09.057 ↗
50. Creep behavior of in situ TiCP/2618 aluminum matrix composite10.1016/j.msea.2008.11.010 ↗
51. Effect of loading history on the threshold stress in the creep deformation of an austenitic stainless steel10.1016/j.msea.2007.04.005 ↗
52. Threshold stress and load partitioning during creep of metal matrix composites10.1016/j.actamat.2008.01.037 ↗
53. Investigation of creep threshold stresses using in situ TEM straining experiment in an Al–5Y2O3–10SiC composite10.1016/j.msea.2009.12.015 ↗
54. On the threshold stress for superplasticity in Mg–Al–Zn alloys10.1016/j.scriptamat.2007.07.002 ↗
55. Hot deformation behavior of in-situ nanosized TiB2 particulate reinforced AZ91 mg matrix composite10.1016/j.jallcom.2019.05.244 ↗
56. Effect of tensile strain rate on high-temperature deformation and fracture of rolled Al-15 vol. % B4C composite10.1016/j.msea.2019.02.016 ↗
57. Effect of microstructure and microtexture evolution on creep behavior of hot-rolled and mushy-state rolled Al-4.5Cu-5TiB2 in-situ composite10.1016/j.msea.2019.05.106 ↗
58. Strong in-plane anisotropy of creep ageing behavior in largely pre-deformed Al-cu alloy: experiments and constitutive modeling10.1016/j.ijplas.2022.103245 ↗