journal article·2021-02Open access

Deformation and failure behaviour of a titanium alloy Ti-407 with reduced aluminium content: A comparison with Ti-6Al-4V in tension and compression

Scott Sneddon, Daniel M. Mulvihill, Euan Wielewski, Mark Dixon, David Rugg, Peifeng Li

Publisher page

Abstract

The titanium alloy Ti-407 (Ti407) is a new alloy being considered for single load to failure applications where energy absorption is a key requirement. This work characterised the deformation and failure mechanisms of Ti407 in uniaxial tension and compression at quasi-static and increased strain rates. The results are compared with equivalent tests on Ti-6Al-4 V (Ti64) to provide a benchmark. The stress-strain data under each condition reveals reduced strength but significantly increased ductility in the Ti407 alloy compared to Ti64. The reduced aluminium content in Ti407 is thought to allow additional dislocation motion and delay crack initiation and propagation. The crystallographic texture analysis on deformed specimens further suggests that in response to an applied stress, Ti407 proves more sensitive to texturing and exhibits greater grain elongation and rotation in comparison to Ti64. Its ability to accommodate significantly more deformation before failure (than Ti64) will provide opportunities for improved impact energy absorption performance, as well as improved machinability and formability (and potentially lower manufacturing cost).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · High-Velocity Impact and Material Behavior · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. The variation of strain rate sensitivity exponent and strain hardening exponent in isothermal compression of Ti-6Al-4V alloy10.1016/j.matdes.2009.09.055 ↗
2. Process parameters optimization of Ti-6Al-4V alloy sheet during hot stretch-creep forming10.1016/S1003-6326(15)63619-6 ↗
3. Timetal® 407: A titanium alloy to enable cost reduction
4. Sensitivity of material failure to surface roughness: a study on titanium alloys Ti64 and Ti407
5. Lütjering · 2010
6. Donachie · 2000
7. Leyens · 2003
8. Anisotropic response of high-purity alpha-titanium: experimental characterization and constitutive modeling10.1016/j.ijplas.2009.08.007 ↗
9. Intrinsic anisotropy of strain rate sensitivity in single crystal alpha titanium10.1016/j.actamat.2016.07.044 ↗
10. Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline Ti using high energy X-ray diffraction microscopy10.1016/j.actamat.2017.05.015 ↗
11. Anisotropy in the plastic flow properties of single-crystal alpha titanium determined from micro-cantilever beams10.1016/j.actamat.2009.07.064 ↗
12. A comparative study on the substructure evolution and mechaniccal properties of TIMETAL®407 and Ti-64
13. Impact of texture on mechanical properties in an advanced titanium alloy10.1016/S0921-5093(00)02034-7 ↗
14. Electron backscatter diffraction study of dislocation content of a macrozone in hot-rolled Ti-6Al-4V alloy10.1016/j.scriptamat.2010.01.010 ↗
15. Lunt · 2014
16. Characterising the effects of strain rate, crystallographic texture and direction of loading on the mechanical behaviour of Ti-6Al-4V10.1007/s40870-015-0040-4 ↗
17. The effect of aluminium on twinning in binary alpha-titanium10.1016/j.actamat.2015.09.048 ↗
18. Giovanola · 1992
19. Response of titanium alloys to high strain rate deformation10.1179/174328405X20950 ↗
20. Effects of high rates of loading on the deformation behavior and failure mechanisms of hexagonal close-packed metals and alloys10.1007/s11661-002-0162-x ↗
21. Characterisation and constitutive model of tensile properties of selective laser melted Ti-6Al-4V struts for microlattice structures10.1016/j.msea.2018.04.006 ↗
22. Dynamic compressive behaviour of Mg foams manufactured by the direct foaming process10.1016/j.matdes.2015.10.021 ↗
23. The rate dependent response of a titanium alloy subjected to quasi-static loading in ambient environment10.1023/A:1021085026220 ↗
24. Effect of interstitial solutes on the strength and ductility of titanium10.1016/0079-6425(81)90001-3 ↗
25. Compressive properties and micro-structural characteristics of Ti–6Al–4V fabricated by electron beam melting and selective laser melting10.1016/j.msea.2019.138204 ↗
26. Analysis of the different slip systems activated by tension in a alpha/beta titanium alloy in relation with local crystallographic orientation10.1016/j.actamat.2004.09.040 ↗
27. An experimental investigation into the micro-mechanics of spall initiation and propagation in Ti-6Al-4V during shock loading10.1016/j.msea.2013.04.055 ↗
28. A study on compression test on Ti-6Al-4V in various strain rates and various temperature
29. Deformation response of titanium alloy under static and dynamic loading
30. Thermomechanical response of 3D laser-deposited Ti-6Al-4V alloy over a wide range of strain rates and temperatures10.1016/j.msea.2015.08.043 ↗
31. Self-organization of shear bands in titanium and Ti-6Al-4V alloy10.1016/S1359-6454(01)00356-1 ↗
32. The effect of strain rate, specimen geometry and lubrication on responses of aluminium AA2024 in uniaxial compression experiments10.1007/s11340-008-9129-1 ↗
33. Adiabatic shear fracture of titanium alloy subjected to high strain rate and high temperature loadings
34. Strain hardening of titanium alloy Ti6Al4V sheets with prior heat treatment and cold working10.1016/j.msea.2016.03.094 ↗
35. Introduction and comparison of new EBSD post-processing methodologies10.1016/j.ultramic.2015.08.001 ↗