Enhancing tensile properties of wrought Ni-based superalloy ATI 718Plus at elevated temperature via morphology control of η phase
Source abstract
Abstract
Abstract The evolution of η phase and its effect on the tensile properties at 700 °C in 718Plus superalloy after three solution (at 940 °C for 1 h) and single aging (at 870 °C for 25 h, 50 h and 100 h) heat treatments, were investigated. The results showed that there were several various morphologies of η phase in 718Plus samples. As aging time increased, the volume fraction of needle-like/plate-like increased continuously from 5.32%, 7.78% to 29.52%, while the volume of granular/short rod-like η phase firstly increased from 0.46% to 0.68% then decreased to 0.56%. The high temperature tensile properties were affected by η phases with various morphologies. With aging time increasing, the ultimate tensile strength was obviously improved from 797.11 MPa to 860.57 MPa, which could be attributed to a certain number of plate-like/needle-like η phases at the grain boundaries which could hinder the dislocations motion near the grain boundaries. And the elongation weakly increased firstly from 16.84% to 18.76% and then decreased to 18%, which was closely related to granular/short-rod η phases. Enhancing tensile strength and acceptable ductility could be obtained by morphology control of η phase applying SA heat treatments in the study: promoting the simultaneous precipitation of an appropriate amount of plate-like/needle-like η phases and a small amount of granular/short rod-like η phases.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Microstructural investigation of thermally aged nickel-based superalloy 718Plus10.1016/j.msea.2013.11.037 ↗
2. The microstructure of heat-treated nickel-based superalloy 718Plus10.1016/j.msea.2014.05.022 ↗
3. The effect of boron and zirconium on microstructure and tensile properties of the wrought nickel-based superalloy ATI 718 Plus10.1016/j.msea.2017.12.038 ↗
4. Precipitation behavior during high-temperature isothermal compressive deformation of Inconel 718 alloy10.1016/j.msea.2016.09.088 ↗
5. Hot tensile behavior of cold-rolled Inconel 718 alloy at 650 °C: the role of δ phase10.1016/j.msea.2018.02.093 ↗
6. Effects of cold rolling on the precipitation kinetics and the morphology evolution of intermediate phases in Inconel 718 alloy10.1016/j.jallcom.2015.07.149 ↗
7. Grain-boundary precipitation in Allvac 718Plus10.1016/j.actamat.2012.01.042 ↗
8. The effect of aluminum on microstructure and mechanical properties of ATI 718Plus alloy10.2320/matertrans.M2014378 ↗
9. Effect of the precipitation of the η-Ni3Al0.5Nb0.5 phase on the microstructure and mechanical properties of ATI 718Plus10.1016/j.jallcom.2017.01.145 ↗
10. Effect of grain boundary misorientation on η phase precipitation in Ni-base superalloy 718Plus10.1016/j.matchar.2019.02.038 ↗
11. Cellular η phase precipitation and its effects on the tensile properties in an Fe-Ni-Cr alloy10.1016/j.msea.2007.11.039 ↗
12. Precipitation of η phase and its effects on stress rupture properties of K4750 alloy10.1016/j.msea.2019.138137 ↗
13. Formation of σ and η phase in three polycrystalline superalloys and their impact on tensile properties10.1016/j.msea.2009.09.016 ↗
14. Morphology and kinetics of grain boundary precipitation in alloy ATI 718Plus®
15. Structure stability study of a newly developed nickel-base superalloy-ALLVAC® 718 PlusTM
16. Microstructure evolution in the nickel base superalloy all allvac®718PlusTM
17. The influence of δ phase on mechanical properties of ATI 718Plus alloy
18. Delta precipitation in wrought Inconel 718 alloy; the role of dynamic recrystallization10.1016/j.matchar.2017.09.032 ↗
19. δ Phase precipitation in Inconel 718 and associated mechanical properties10.1016/j.msea.2016.09.114 ↗
20. The effect of interdendritic δ phase on the mechanical properties of Alloy 718 built up by additive manufacturing10.1016/j.matdes.2016.12.026 ↗
21. Tensile deformation and fracture characteristics of delta-processed Inconel 718 alloy at elevated temperatures10.1016/j.msea.2011.04.074 ↗
22. Effects of alloying elements on microstructure and mechanical properties of Co–Ni–Al–Ti superalloy10.1016/j.msea.2020.139139 ↗
23. Tensile deformation behavior of superalloy 718 at elevated temperatures10.1016/j.jallcom.2008.03.082 ↗
24. Dislocation network in additive manufactured steel breaks strength–ductility trade-off10.1016/j.mattod.2017.11.004 ↗
25. Achieving a desirable combination of mechanical properties in HSLA steel through step quenching10.1016/j.msea.2019.138683 ↗
26. On conventional versus direct ageing of Alloy 71810.1016/j.actamat.2018.06.034 ↗