Understanding the mechanism of Beraha-I type color etching: Determination of the orientation dependent etch rate, layer refractive index and a method for quantifying the angle between surface normal and the 〈100〉, 〈111〉 directions for individual grains
Source abstract
Abstract
Abstract A grey cast iron specimen was investigated by Beraha-I type color etching for the purpose of developing a functional model for the etching kinetics and subsequently a method which would enable the estimation of ferrite grain orientations with respect to specific directions, solely based on optical microscopy. For this, the etching process was observed real-time in a microfluidic cell and a custom image processing software was developed to interpret the color information. Scanning electron microscopy with electron backscatter diffraction (SEM-EBSD) and atomic force microscopy (AFM) were used to determine the grain orientation and the relative thickness of the developed interference layer respectively, which were used for further calculations. It was shown that in the initial phase the etching process experiences a delay, which can be connected to breaking an oxide barrier above the ferrite grains. This delay was found to be influenced by the idle time between sample preparation and the start of etching. However, it was proven that a characteristic cycle etch rate can be defined between the first interference minimum and maximum, which shows correlation with both the 〈100〉 and 〈111〉 directions and which is also independent from the delay during the initiation phase. The exact value and orientation dependence of this cycle etch rate was experimentally determined along with the refractive index of the developed film. Our method was demonstrated to be applicable for the estimation of the angle between the surface normal and the 〈100〉, 〈111〉 directions for individual ferrite grains in the cast iron specimen, with an average absolute error of 3°, by using optical microscopy only. The method is implemented and was made available in the form of a Matlab program.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Photolithography Techniques · Integrated Circuits and Semiconductor Failure Analysis · Nanofabrication and Lithography Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Metallography
2. Effect of specimen preparation on evaluation of cast iron microstructures10.1016/j.matchar.2004.08.019 ↗
3. A new etching route for revealing the austenite grain boundaries in an 11.4% Cr precipitation hardening semi-austenitic stainless steel10.1016/j.matchar.2006.06.009 ↗
4. Correlation between grain orientation and the shade of color etching10.1016/j.matchar.2010.05.005 ↗
5. New metallographic reagents for stainless steel and heat-resisting alloys
6. Ätzmittel zur Sichtbarmachung chemischer und physikalischer Inhomogenitäten in Stahlgefügen10.1515/pm-1967-040805 ↗
7. Effect of grain orientation on chemical etching10.1016/j.micron.2011.09.015 ↗
8. Correlation between the grain orientation dependence of color etching and chemical etching10.1017/S1431927612013554 ↗
9. Opening the door to fundamental understanding of structure and color metallography - a correlative microscopy study on steel10.1017/S1431927614005893 ↗
10. Reproducible surface contrasting and orientation correlation of low-carbon steels by time-resolved Beraha color etching10.1520/MPC20160067 ↗
11. Differentiation of grain orientation with corrosive and colour etching on a granular bainitic steel10.1016/j.micron.2017.04.002 ↗
12. DowCorning Corp. “Product Information: Sylgard 184 Silicone Elastomer” (Form 10-898F-01.)
13. 3D Rapid Prototyping Technology (RPT) as a powerful tool in microfluidic development10.1016/j.proeng.2010.09.105 ↗
14. Gwyddion: an open-source software for SPM data analysis
15. CIE · 1932
16. Flory · 2018
17. Optical properties of Al, Fe, Ti, Ta, W, and Mo at submillimeter wavelengths10.1364/AO.27.001203 ↗
18. Jenkins · 1981
19. New ways in metallography: through controlled conditions to objective microstructure analysis of low-carbon steels by LePera-etching
20. Development of ferritic stainless steel sheets with excellent deep drawability by {1 1 1} recrystallization texture control10.1016/S0389-4304(03)00082-1 ↗
21. The effects of texture on the corrosion resistance of SS304 stainless steel
22. Gahm, Jeglitsch - Color Methods and Their Application in Metallography - 1981.pdf