Hot deformation characteristics and microstructure evolution of electroslag remelted 15Cr-22Ni-1Nb austenitic heat-resistant steel
Source abstract
Abstract
Abstract The hot deformation and microstructure characteristics of a novel austenitic heat-resistant steel were investigated based on isothermal compression tests. A strain-compensated modified constitutive model is established, which is capable to accurately predict the flow behaviors of the steel. A kinetic model is established to predict dynamic recrystallization volume fraction. The fraction of dynamic recrystallization increases with increasing the deformation temperature, and decreases with the increase in the strain rate. The volume fraction of dynamic recrystallization is close to 100% at the strain rates of 0.01 s−1 and 0.1 s−1 at 1150 °C. The size of dynamic recrystallized grains increases with the increase in the deformation temperature. The recrystallized grain size decreases with increasing the strain rate up to 1 s−1, whereas an opposite trend is exhibited when the strain rate is greater than 1 s−1. Hot deformation induced the precipitation of fine NbC (at deformation temperature of 950–1150 °C) and Fe2Nb-type Laves phase (deformation temperature ≤ 1000 °C) particles at the grain boundaries and dislocations in the designed austenitic heat-resistant steel. The dynamic recrystallization is hindered because of the pinning role of fine Fe2Nb-type Laves phase and NbC precipitates on the dislocations and grain boundaries. Hot processing maps of the austenitic heat-resistant steel were constructed, and the optimal processing parameters were determined as 1100–1150 °C / 0.01–0.1 s−1.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. Precipitation and growth of γ’ and η phases in 53Fe-26Ni-15Cr alloy10.2355/isijinternational.35.542 ↗
2. Microstructure and properties after deformation and aging process of A286 superalloy10.1007/s12598-018-1171-2 ↗
3. The mechanism of precipitation strengthening in an iron-base superalloy10.1016/0001-6160(82)90140-7 ↗
4. Effect of boron addition on hydrogen embrittlement sensitivity in Fe–Ni based alloys10.1016/j.msea.2010.06.073 ↗
5. Fatigue-induced precipitates at grain boundary of Nb-A286 alloy in high temperature low cycle fatigue10.1016/S0921-5093(00)00975-8 ↗
6. The mechanism of η phase precipitation in A286 superalloy during heat treatment10.1007/s11665-013-0592-1 ↗
7. The role of η phase on the strength of A286 superalloy with different Ti/Al ratios10.1134/S0031918X20030059 ↗
8. Microstructural development and creep behavior in A286 superalloy10.1016/j.matchar.2004.03.007 ↗
9. Effect of η phase on mechanical properties of the iron-based superalloy using shear punch testing10.2355/isijinternational.53.311 ↗
10. Potentiodynamic study of the influence of gamma prime and eta phases on pitting corrosion of A286 superalloy10.1016/j.jallcom.2016.02.261 ↗
11. Application research of high temperature alloy material in copper and copper alloy extrusion dies
12. Effects of tungsten and molybdenum on high-temperature tensile properties of five heat-resistant austenitic stainless steels10.1016/j.msea.2016.01.022 ↗
13. Effect of molybdenum on hardness of low-temperature plasma carburized austenitic stainless steel10.1016/j.surfcoat.2006.07.127 ↗
14. Experimental study and numerical simulation of dynamic recrystallization behavior of a micro-alloyed plastic mold steel10.1016/j.matdes.2014.10.076 ↗
15. Micro-textures and mechanical properties of Fe–21Cr–15Ni–6Mn–Mo–Nb austenitic stainless steel plate in asymmetric hot rolling10.1016/j.msea.2020.140565 ↗
16. Complicated interaction of dynamic recrystallization and precipitation during hot deformation of ultrahigh-strength stainless steel
17. A study on microstructural evolution and dynamic recrystallization during isothermal deformation of a Ti-modified austenitic stainless steel10.1007/s11661-010-0517-7 ↗
18. On the constitutive modeling and microstructural evolution of hot compressed A286 iron-base superalloy10.1016/j.jallcom.2013.01.156 ↗
19. High temperature deformation characteristics of an alumina-forming stainless steel10.1002/srin.201900022 ↗
20. Hot deformation behavior and microstructural evolution of SA508-IV steel10.1002/srin.201800208 ↗
21. Hot deformation behavior and microstructure analysis of 25Cr3Mo3NiNb steel during hot compression tests10.1016/j.vacuum.2017.10.017 ↗
22. Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining10.1007/s12613-013-0820-6 ↗
23. Recrystallization of 30Cr2Ni4MoV ultra-super-critical rotor steel during hot deformation. Part I: dynamic recrystallization10.1016/j.msea.2011.03.008 ↗
24. EBSD study of a hot deformed nickel-based superalloy10.1016/j.jallcom.2015.04.008 ↗
25. Study of dynamic recrystallization in a Ni-based superalloy by experiments and cellular automaton model10.1016/j.msea.2014.12.092 ↗
26. Effect of strain rate upon plastic flow of steel10.1063/1.1707363 ↗
27. On the mechanism of hot deformation10.1016/0001-6160(66)90207-0 ↗
28. A critical review of experimental results and constitutive descriptions for metals and alloys in hot working10.1016/j.matdes.2010.11.048 ↗
29. A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization10.1016/1359-6454(95)00146-7 ↗
30. Determination of critical strain for initiation of dynamic recrystallization10.1016/j.matdes.2009.09.001 ↗
31. New formula for calculation flow curves from high temperature constitutive data for 300 austenitic steels10.1016/0924-0136(92)90236-L ↗
32. Proportion of recovery and recrystallization during interpass times at high temperatures on a Nb- and N-bearing austenitic stainless steel biomaterial10.1016/j.scriptamat.2006.05.015 ↗
33. Dynamic recrystallization behavior of a medium carbon vanadium microalloyed steel10.1016/j.msea.2013.03.009 ↗
34. The Avrami kinetics of dynamic recrystallization10.1016/j.actamat.2009.02.033 ↗
35. Study on the dynamic recrystallization model and mechanism of nuclear grade 316LN austenitic stainless steel10.1016/j.matchar.2016.05.015 ↗
36. Dynamic recrystallization behavior of GH4169G alloy during hot compressive deformation10.1016/j.jmst.2019.04.018 ↗
37. Abnormal dynamic recrystallization behavior of a nickel based superalloy during hot deformation10.1016/j.jallcom.2019.02.055 ↗
38. Effect of strain rate on the dynamic recrystallization behavior in a nitrogen-enhanced 316L(N)10.1007/s11661-014-2480-1 ↗
39. An electron backscattered diffraction study on the dynamic recrystallization behavior of a nickel–chromium alloy (800H) during hot deformation10.1016/j.msea.2013.07.037 ↗
40. On microstructure characterization of Fe–Cr–Ni–Mo–N super-austenitic stainless steel during hot deformation10.1007/s42243-018-0203-3 ↗
41. Modeling of dynamic material behavior in hot deformation: forging of Ti-624210.1007/BF02664902 ↗
42. Characterization of hot deformation behavior and processing map of as-cast H13 hot work die steel
43. A study on flow behavior of A-286 superalloy during hot deformation10.1016/j.matchemphys.2006.03.012 ↗
44. Flow behaviour and microstructural evolution of 53Fe–26Ni–15Cr superalloy during hot compression test10.1179/174328107X155213 ↗
45. Hot deformation characteristic and processing map of superaustenitic stainless steel S3265410.1016/j.msea.2014.01.027 ↗
46. Adiabatic shear band formation during dynamic torsional deformation of an HY-100 steel10.1016/0956-7151(93)90026-O ↗
47. Dynamic recrystallization under warm deformation of a 304 type austenitic stainless steel10.1016/S0921-5093(98)00784-9 ↗