journal article·2013-05

Microstructural and textural evolution of AZ61 magnesium alloy sheet during bidirectional cyclic bending

Qinghuan Huo, Xuyue Yang, Jijun Ma, Huan Sun, Jia Qin, Yupei Jiang

Publisher page

Abstract

Abstract In this work, the microstructural and textural evolution in the sheets of AZ61 magnesium alloy was studied by means of bidirectional cyclic bending for 8 passes at 623 K. The bended samples were examined by optical microscopy and electron backscatter diffraction analysis. The results showed that a gradient structure with fine grains about 3 μm in the regions near two surfaces and, in contrast, coarse grains in the middle of the sheet were formed. The evident grain refinement was attributed to twin-assisted dynamic recrystallization and continuous dynamic recrystallization induced by kink bands. The texture intensity was clearly reduced, resulting in a negative gradient distribution, with the texture intensity decreases from the center of the sheet to two surfaces. The weakened texture greatly facilitated the reduction of the yield strength. A higher fracture elongation and a slightly improved ultimate tensile strength were achieved concurrently.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Twinning behavior of a strongly basal textured AZ31 Mg alloy during warm rolling10.1016/j.actamat.2011.12.017 ↗
2. Annealing of a magnesium alloy AZ31 after interrupted cold deformation10.1016/j.matdes.2011.12.001 ↗
3. Influence of rolling temperature on static recrystallization behavior of AZ31 magnesium alloy10.1007/s10853-012-6314-5 ↗
4. On the anisotropic deformation of AZ31 Mg alloy under compression10.1016/j.matdes.2011.06.017 ↗
5. Dynamic evolution of new grains in magnesium alloy AZ31 during hot deformation10.2320/matertrans.44.197 ↗
6. Sensitivity of deformation twinning to grain size in titanium and magnesium10.1016/j.actamat.2011.09.018 ↗
7. Effect of plate-shaped particle distributions on the deformation behaviour of magnesium alloy AZ91 in tension and compression10.1016/j.actamat.2011.10.001 ↗
8. Static recrystallization kinetics of a heavily cold drawn AZ31 magnesium alloy under annealing treatment10.1016/j.matchar.2011.01.007 ↗
9. Production of ultrafine-grain microstructure in Mg alloy by alternate biaxial reverse corrugation10.1016/j.actamat.2006.06.045 ↗
10. Enhanced stretch formability and mechanical properties of a magnesium alloy processed by cold forging and subsequent annealing10.1016/j.matdes.2012.06.065 ↗
11. Effect of pass strain and temperature on recrystallization in magnesium alloy AZ31 after interrupted cold deformation10.1007/s10853-011-6111-6 ↗
12. The effect of Gd on the recrystallization, texture and deformation behaviour of magnesium-based alloys10.1016/j.actamat.2010.09.003 ↗
13. Accumulative roll bonding of a Mg-based AZ61 alloys10.1016/j.msea.2005.08.097 ↗
14. Network-shaped fine-grained microstructure and high ductility of magnesium alloy fabricated by cyclic extrusion compression10.1016/j.scriptamat.2007.09.058 ↗
15. Textures and stretch formability of Mg–6Al–1Zn magnesium alloy sheets rolled at high temperatures up to 793K10.1016/j.scriptamat.2008.12.035 ↗
16. The effect of texture and strain conditions on formability of cross-roll rolled AZ31 alloy10.1016/j.jallcom.2011.07.013 ↗
17. Texture weakening of AZ31 magnesium alloy sheet obtained by a combination of bidirectional cyclic bending at low temperature and static recrystallization10.1007/s10853-012-6814-3 ↗
18. Processing of metals by severe plastic deformation (SPD) — structure and mechanical properties respond
19. Twinning and the ductility of magnesium alloys Part I: “Tension” twins10.1016/j.msea.2006.12.037 ↗
20. Twinning and the ductility of magnesium alloys Part II. “Contraction” twins10.1016/j.msea.2007.02.109 ↗
21. Orientational analysis of static recrystallization at compression twins in a magnesium alloy AZ3110.1016/j.msea.2009.03.045 ↗
22. Twinning, dynamic recovery and recrystallization in hot worked Mg–Al–Zn alloy10.1016/S0921-5093(02)00007-2 ↗
23. Influence of twinning on the grain refinement during high-temperature deformation in a magnesium alloy10.1016/j.scriptamat.2010.11.009 ↗
24. The role of twinning and untwining in yielding behavior in hot-extruded Mg–Al–Zn alloy10.1016/j.actamat.2006.09.010 ↗
25. Dynamic recrystallization and the development of microstructure during the high temperature deformation of magnesium10.1016/0001-6160(82)90031-1 ↗
26. Development of dynamic recrystallization theory10.1016/j.msea.2004.01.064 ↗
27. Dynamic continuous recrystallization characteristics in two stage deformation of Mg–3Al–1Zn alloy sheet10.1016/S0921-5093(02)00096-5 ↗
28. Influence of grain size on the compressive deformation of wrought Mg–3Al–1Zn10.1016/j.actamat.2004.07.015 ↗
29. Multi-directional forging of AZ61 Mg alloy under decreasing temperature conditions and improvement of its mechanical properties10.1016/j.msea.2011.05.050 ↗
30. Grain growth kinetics of bulk AZ31 magnesium alloy by hot pressing10.1016/j.jallcom.2012.03.006 ↗
31. High temperature deformation and extruded plasticity in Mg single crystals10.1080/14786430500228440 ↗
32. Grain size and texture control of Mg–3Al–1Zn alloy sheet using a combination of equal-channel angular rolling and high-speed-ratio differential speed-rolling processes10.1016/j.scriptamat.2009.02.005 ↗
33. Isochronal annealing behavior of magnesium alloy AZ31 after hot deformation10.2320/matertrans.46.2981 ↗
34. Improvement of stretch formability of Mg–3Al–1Zn alloy sheet by high temperature rolling at finishing pass10.1016/j.jallcom.2011.04.132 ↗