Friction stir welding of as-extruded Mg–Al–Zn alloy with higher Al content. Part I: Formation of banded and line structures
Source abstract
Abstract
Abstract 6-mm-thick extruded Mg–Al–Zn (AZ80) alloy plates were subjected to friction stir welding at a welding speed of 100 mm·min− 1 and tool rotation rates of 400–1200 rpm, and the highest joint efficiency of 92% was achieved at 800 rpm. Friction stir welding resulted in the dissolution of coarse β-Mg17Al12 particles, with fewer and smaller β particles distributed at the grain boundaries in the nugget zones; meanwhile, banded structures resulting from different Al concentrations were observed in the nugget zones. As the rotation rate increased, the grain size of the nugget zones increased, but the β particles showed little variation in the quantity and size. At low rotation rates, uniform microstructures were produced in the joints, and during tensile testing the joints failed in the nugget zones where was the lowest hardness region of the joints. However, a line structure containing the β particles was observed at the boundary of the nugget zone at the highest rotation rate, which resulted in a decrease in the tensile properties. The results indicated that higher rotation rates would not be suitable for the friction stir welding of wrought Mg–Al–Zn alloys with higher Al content.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Magnesium Alloys: Properties and Applications · MXene and MAX Phase Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
2. Plastic anisotropy and the role of non-basal slip in magnesium alloy AZ31B10.1016/j.ijplas.2004.05.018 ↗
3. Effects of heat input on tensile properties and fracture behavior of friction stir welded Mg–3Al–1Zn alloy10.1016/j.msea.2009.09.044 ↗
4. Friction stir welding of AZ31 magnesium alloy rolled sheets: influence of processing parameters10.1016/j.actamat.2008.09.011 ↗
5. The influence of the ratio of “rotational speed/traverse speed” (ω/ν) on mechanical properties of AZ31 friction stir welds10.1016/j.ijmachtools.2006.01.007 ↗
6. Joint properties of friction stir welded AZ31B-H24 magnesium alloy10.1179/026708303225001867 ↗
7. Basal plane texture and flow pattern in friction stir weld of a magnesium alloy10.1007/s11661-003-0228-4 ↗
8. Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test10.1016/S1359-6462(03)00210-0 ↗
9. The microstructure and mechanical properties of friction stir welded Mg–3Al–1Zn alloy at high rotation rates
10. Microstructural evolution and its effect on Hall–Petch relationship in friction stir welding of thixomolded Mg alloy AZ91D10.1023/A:1026351619636 ↗
11. The joint characteristics of friction stir welded AZ91D magnesium alloy10.2320/matertrans.44.917 ↗
12. Analysis of the grain orientation and texture of friction stir welded magnesium alloy10.4028/www.scientific.net/MSF.620-622.97 ↗
13. Effect of microstructural evolution on mechanical properties of friction stir welded ZK60 alloy10.1016/j.msea.2007.08.043 ↗
14. Microstructure–property studies in friction-stir welded, thixomolded magnesium alloy AM6010.1023/A:1022321107957 ↗
15. Microstructural evolution and mechanical properties of friction stir welded Mg–Zn–Y–Zr alloy10.1016/j.msea.2007.03.041 ↗
16. Microstructural evolution of a heat-resistant magnesium alloy due to friction stir welding10.1016/j.scriptamat.2005.01.003 ↗
17. Effect of Y addition on microstructure and mechanical properties of friction stir welded ZK60 alloy
18. Effects of friction stir welding parameters on microstructures and mechanical properties of ZK60 magnesium alloy joints
19. Effects of rotation rates on microstructure, mechanical properties, and fracture behavior of friction stir-welded (FSW) AZ31 magnesium alloy10.1007/s11661-012-1373-4 ↗
20. Specific character of material flow in near-surface layer during friction stir processing of AZ31 magnesium alloy10.1007/s11661-009-0158-x ↗
21. Effect of friction stir processing procedures on microstructure and mechanical properties of Mg–Al–Zn casting10.1007/s11661-009-9923-0 ↗
22. Microstructure and properties of AZ80 magnesium alloy prepared by hot extrusion from recycled machined chips
23. A flow-partitioned deformation zone model for defect formation during friction stir welding10.1016/j.scriptamat.2007.10.031 ↗
24. Effect of friction stir processing on the microstructure of cast A356 aluminum10.1016/j.msea.2006.06.099 ↗
25. Enhanced mechanical properties of Mg–Al–Zn cast alloy via friction stir processing10.1016/j.scriptamat.2006.10.035 ↗
26. Quantitative characterization of Mg17Al12 phase and grain size in HPDC AZ91 magnesium alloy10.1016/j.jallcom.2007.07.017 ↗
27. Effects of heat treatment on microstructure and tensile deformation of Mg AZ80 alloy at room temperature10.1016/j.msea.2008.05.019 ↗
28. Microstructural refinement and property enhancement of cast light alloys via friction stir processing10.1016/j.scriptamat.2007.09.062 ↗
29. A process model for friction stir welding of age hardening aluminum alloys10.1007/s11661-001-0128-4 ↗
30. Influence of tool dimension and welding parameters on microstructure and mechanical properties of friction-stir-welded 6061-T651 aluminum alloy10.1007/s11661-008-9586-2 ↗
31. Microstructural studies of friction stir welds in 2024-T3 aluminum10.1016/S0921-5093(01)01358-2 ↗
32. A study of texture patterns in friction stir welds10.1016/j.actamat.2007.11.016 ↗
33. Coupled thermo-mechanical model based comparison of friction stir welding processes of AA2024-T3 in different thicknesses10.1007/s10853-011-5537-1 ↗
34. Simulation and experimental investigation of FSP of AZ91 magnesium alloy10.1016/j.msea.2011.05.035 ↗
35. Effect of tool angle on metal flow phenomenon in friction stir welds
36. Tensile behavior of friction stir welded AZ31-H24 Mg alloy10.1007/s11661-005-0252-7 ↗
37. High temperature deformation of the gamma-Mg17Al12 complex metallic alloy10.1016/j.scriptamat.2011.04.022 ↗
38. Grain structure evolution during friction-stir welding of AZ31 magnesium alloy10.1016/j.actamat.2009.07.041 ↗
39. Fracture behavior of AZ91 magnesium alloy10.1016/S0167-577X(00)00041-0 ↗