The cryogenic low-cycle fatigue performance of 9%Ni steel joint made by flux cored arc welding
Source abstract
Abstract
Abstract Low-cycle fatigue (LCF) test was performed at 296 K and 80 K to investigate the effects of cryogenic environment on the LCF performance of 9%Ni steel joints welded by flux cored arc welding (FCAW). The test results indicated that the LCF performance in cryogenic environment was higher than that at room temperature. The gap of fatigue lifetime decreased with the increment of strain amplitude. The LCF performance at room temperature and in cryogenic environment was very close when total strain amplitude was 0.8%. The LCF specimens underwent cyclic hardening and cyclic softening before fracture at room temperature. No obvious cyclic softening was observed during LCF test at cryogenic temperature. The fracture location was at PMZ at room temperature, but at weld center in cryogenic environment. The transformation of brass texture mainly occurred in PMZ at cryogenic temperature after LCF test. The strengthening effects of brass texture in PMZ increased the stress concentration in weld center. The microvoids appeared near precipitates at grain boundaries led to the intergranular propagation of fatigue cracks in weld center. Research results contributed to safe service and fatigue lifetime estimation of LNG containers made by 9% Ni steel in cryogenic environment.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. Xu · 2017 · 11
2. Fatigue failure at cryogenic temperatures10.3103/S1068798X17100124 ↗
3. Fracture mode transition in low-temperature low-cycle fatigue of commercial pure iron10.1299/kikaia.62.1800 ↗
4. An experimental study on fatigue performance of cryogenic metallic materials for IMO type B tank10.2478/IJNAOE-2013-0155 ↗
5. Microstructural evolution and mechanical properties of high strength 3–9% Ni-steel alloys weld metals produced by electron beam welding10.1016/j.matdes.2014.03.056 ↗
6. A study of fracture toughness and microstructures in the weld heat-affected zone of QLT-processed 9% Ni steel
7. Experimental analysis of the practical LBZ effects on the brittle fracture performance of cryogenic steel HAZs with respect to crack arrest toughness near fusion line10.1016/S0013-7944(02)00111-X ↗
8. Significant system parameters influencing HAZ properties in 9%Ni steel10.1179/136217101101538758 ↗
9. Crack-initiation toughness and crack-arrest toughness in advanced 9% Ni steel welds containing local brittle zones10.1007/s11661-002-0383-z ↗
10. Effect of Re on low-cycle fatigue behaviors of Ni-based single-crystal superalloys at 900°C10.1016/j.msea.2014.02.073 ↗
11. Low cycle fatigue behaviour of a Cr–Mo–V matrix-type high-speed steel used for cold forging10.1016/j.matdes.2012.08.052 ↗
12. Effect of heat treatment on Coffin–Manson relationship in LCF of superalloy IN71810.1016/j.msea.2007.08.005 ↗
13. Characterization of the microstructures and the cryogenic mechanical properties of electron beam welded Inconel 718
14. Physical mechanisms of nanocrystallization of a novel Ni-based alloy under uniaxial compression at cryogenic temperature10.1016/j.matchar.2016.03.024 ↗
15. Plastic deformation mechanisms of NiCuCrMoTiAlNb Ni-based alloys at cryogenic temperature10.1016/j.msea.2016.03.133 ↗
16. Strain controlled cyclic deformation behavior of an extruded magnesium alloy10.1016/j.msea.2008.05.016 ↗
17. Low cycle fatigue behaviour of a Cr–Mo–V matrix-type high-speed steel used for cold forging10.1016/j.matdes.2012.08.052 ↗
18. Inversion of Ramberg–Osgood equation and description of hysteresis loops10.1016/S0020-7462(02)00025-2 ↗
19. Role of butter layer in low-cycle fatigue behavior of modified 9Cr and CrMoV dissimilar rotor welded joint10.1016/j.matdes.2014.02.022 ↗
20. Effect of heat treatment on Coffin–Manson relationship in LCF of superalloy IN71810.1016/j.msea.2007.08.005 ↗
21. El-Sayed M E M. Transition From Low Cycle to High Cycle in Uniaxial Fatigue[C]// ASME 2013 International Mechanical Engineering Congress and Exposition. 2013:V009T10A020-V009T10A020.
22. Cyclic deformation behavior of a cast aluminum alloy10.1016/j.msea.2009.04.037 ↗
23. The microstructure evolution and nucleation mechanisms of dynamic recrystallization in hot-deformed Inconel 625 superalloy10.1016/j.matdes.2010.07.040 ↗
24. Silva Cleiton Carvalho, Miranda HCD, Motta MF, Farias JP, Afonso CRM, Ramirez AJ. New insight on the solidification path of an alloy 625 weld overlay. Journal of Materials Research and Technology. 2013, 2:228–37.10.1016/j.jmrt.2013.02.008 ↗
25. Effects of precipitated phases on the crack propagation behaviour of a Ni-based superalloy10.1016/j.ijfatigue.2013.10.006 ↗
26. Cryogenic fracture toughness of 9%Ni steel flux cored arc welds10.1016/j.jmatprotec.2017.10.026 ↗
27. Calculation of Schmid factors in magnesium: analysis of deformation behaviors10.1016/j.scriptamat.2012.05.042 ↗
28. On the influence of mechanical environment on the emergence of brass textures in FCC metals10.1016/j.actamat.2006.07.017 ↗
29. Influence of shear banding on the formation of Brass-type textures in polycrystalline fcc metals with low stacking fault energy10.1016/j.jmst.2013.11.010 ↗
30. Enhanced fracture toughness in an annealed Al-Cu-Mg alloy by increasing Goss/Brass texture ratio10.1016/j.matchar.2016.07.015 ↗
31. Unexpected brass-type texture in rolling of ultrafine-grained copper10.1016/j.scriptamat.2014.08.012 ↗
32. The effects of microstructure and microtexture generated during solidification on deformation micromechanism in IN713C nickel-based superalloy10.1016/j.actamat.2018.01.062 ↗
33. Micro-mechanisms of deformation texture evolution in nanocrystalline nickel-cobalt alloys10.1016/j.actamat.2016.08.036 ↗
34. Fatigue crack initiation and propagation life of welded joints
35. Effect of size and location of a weld defect on fatigue life for argon-arc welded titanium alloy joint[J]10.4028/www.scientific.net/AMR.33-37.121 ↗
36. Fatigue analysis of welded joints: state of development10.1016/S0951-8339(02)00075-8 ↗