Refining the identification methodology for describing heterogeneous Fe-Si materials using the viscoplastic self-consistent approach
Source abstract
Abstract
Electrical steels stand as the predominant soft ferromagnetic materials in the power transmission industry. The magnetic properties of these steels are linked to a very specific crystallographic texture composed of centimeter-sized grains oriented along the Goss component. The formation of this texture is known to be directly linked with recrystallization mechanisms, abnormal grain growth during the high temperature annealing, as well as the texture evolution during cold rolling. Because of the complexity and heterogeneity of the deformed state, the key controlling parameters of the recrystallization mechanisms and then abnormal grain growth are not yet fully identified. In that context, to get a better understanding of the link between deformation and subsequent recrystallization mechanisms, the cold rolling stage is modelled in the present work as a first step. A viscoplastic self-consistent approach is used, to capture both texture and hardening evolution. The objective is to provide a qualitative and quantitative prediction of the microstructure and mechanical behavior resulting from the rolling process-induced cold deformation. It is thus necessary to establish a representative description of the heterogeneous Fe-Si material before this step: a novel identification methodology is introduced with that aim. Mechanical tests, consisting of tensile and simple shear at varying angles with respect to the rolling direction, were conducted for the sake of parameters identification and validation. Especially, a dislocation-based hardening model integrated in a viscoplastic self-consistent polycrystal framework is used. Required parameters, such as grain morphology, strain rate sensitivity, and microstructure heterogeneity, are discussed to enhance alignment with experimental data. • A new methodology is developed to characterize the heterogeneous Fe-Si steel. • We use a viscoplastic self-consistent model. • Parameters are identified by trial-and-error method on mechanical tests. • Validation is done on deformed texture.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Les aciers électriques pour transformateurs et machines tournantes. Situation actuelle et perspectives
2. Lemaître · 2014
3. Waeckerlé · 2011
4. On the magnetic properties of single crystals of iron10.1038/117753a0 ↗
5. N.P. Goss, Electrical Sheet and Method and Apparatus for its Manufacture and Test, 1933.
6. The evolution of the Goss and cube textures in electrical steel10.1016/j.matlet.2014.01.166 ↗
7. Overview of microstructure and microtexture development in grain-oriented silicon steel10.1016/j.jmmm.2006.02.116 ↗
8. Texture formation in metal alloys with cubic crystal structures10.1080/02670836.2016.1231746 ↗
9. Mechanism of secondary recrystallization of Goss grains in grain-oriented electrical steel10.1080/14686996.2017.1341277 ↗
10. A new model of Goss texture development during secondary recrystallization of electrical steel10.1016/S1359-6454(97)00111-0 ↗
11. Coincidence site lattice (CSL) grain boundaries and goss texture development in Fe-3% Si alloy10.1016/S1359-6454(96)00140-1 ↗
12. Coincidence grain boundary and texture evolution in Fe-3%Si10.1016/0001-6160(89)90118-1 ↗
13. Computer color mapping of configuration of Goss grains after an intermediate annealing in grain oriented silicon steel10.2355/isijinternational1966.27.139 ↗
14. Abnormal grain growth of Goss grains in Fe–3% Si steel driven by sub-boundary-enhanced solid-state wetting: analysis by Monte Carlo simulation10.1016/j.actamat.2010.04.038 ↗
15. Dislocation-assisted particle dissolution: a new hypothesis for abnormal growth of Goss grains in grain-oriented electrical steels10.1016/j.actamat.2023.119170 ↗
16. The Goss texture formation in silicon steels – growth selection or oriented nucleation?10.4028/www.scientific.net/SSP.105.29 ↗
17. Influence of subsurface layers on texture and microstructure development in RGO electrical steel10.1016/0956-7151(93)90331-L ↗
18. Influence of the Goss grain environment during secondary recrystallisation of conventional grain oriented Fe–3%Si steels10.1016/S1359-6462(02)00189-6 ↗
19. Effects of topology on abnormal grain growth in silicon steel10.1016/S1359-6454(02)00574-8 ↗
20. Effect of primary recrystallization microstructure on abnormal growth of Goss grains in a twin-roll cast grain-oriented electrical steel10.1016/j.matdes.2017.06.016 ↗
21. Methods of correlating texture and magnetic properties in electrical steels
22. On the correlation between microstructure and magnetic losses in electrical steel10.1016/j.jmmm.2008.04.056 ↗
23. Experimental identification and physical interpretations of 2D tensor magnetic properties of a grain oriented electrical steel magnetized between the rolling and the transverse directions
24. Tomé · 2023
25. Microstructure evolution and strain localization during shear deformation of an aluminium alloy10.1016/S1359-6454(96)00046-8 ↗
26. Simple shear tests: experimental techniques and characterization of the plastic anisotropy of rolled sheets at large strains10.1016/j.jmatprotec.2005.09.003 ↗
27. Texture analysis with MTEX – free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
28. The intercept method—2. Determination of spatial grain size10.1016/S1359-6454(96)00198-X ↗
29. Viscoplastic self-consistent polycrystal modeling of texture evolution of ultra-low carbon steel during cold rolling10.1088/1361-651X/ab0b92 ↗
30. Effect of cold rolling route on deformation mechanism and texture evolution of thin beryllium foils: experiment and VPSC simulation10.1016/j.matchar.2020.110350 ↗
31. Mechanical response of zirconium—I. Derivation of a polycrystal constitutive law and finite element analysis10.1016/S1359-6454(01)00190-2 ↗
32. The determination of the elastic field of an ellipsoidal inclusion, and related problems
33. Self consistent homogenization methods for texture and anisotropy
34. On the evolution and modelling of cube texture during dynamic recrystallisation of Ni–30Fe–Nb–C model alloy10.1016/j.jallcom.2018.03.031 ↗
35. Texture simulation of a severely cold rolled low carbon steel using polycrystal modeling10.1016/j.ijplas.2018.06.001 ↗
36. Laws for work-hardening and low-temperature creep
37. Physics and phenomenology of strain hardening: the FCC case10.1016/S0079-6425(02)00003-8 ↗
38. A dislocation-based constitutive law for pure Zr including temperature effects10.1016/j.ijplas.2007.07.017 ↗
39. Measurement and prediction of plastic anisotropy in deep-drawing steels10.1007/BF02782413 ↗
40. A crystallographic dislocation model for describing hardening of polycrystals during strain path changes. Application to low carbon steels10.1016/j.ijplas.2012.09.004 ↗
41. Influence of grain shape on the planar anisotropy of rolled steel sheets – evaluation of three models10.1016/j.commatsci.2008.06.013 ↗
42. Polycrystal plasticity models based on crystallographic and morphologic texture: evaluation of predictions of plastic anisotropy and deformation texture10.1016/j.msea.2013.06.008 ↗
43. A dislocation-based constitutive law for pure Zr including temperature effects10.1016/j.ijplas.2007.07.017 ↗
44. Identification methodology of a rate-sensitive constitutive law with mean field and full field modeling approaches for polycrystalline materials10.5802/crmeca.56 ↗
45. Mechanical behavior of low carbon steel subjected to strain path changes: experiments and modeling10.1016/j.actamat.2016.03.075 ↗
46. Modelling the plastic behaviour of metals under complex loading conditions10.1088/0965-0393/19/3/035009 ↗