Instantaneous efficient microstructure manipulation of eutectic Al Si alloy by trace in-situ nanoparticles and their mechanism in superior tensile properties
Source abstract
Abstract
The overall microstructure-manipulated Al-13Si-5Cu-0.6 Mg alloy was successfully fabricated via introducing 0.1 wt% Zr 55Cu 30Al 10Ni 5 amorphous alloy manipulator with short time of 60 s, to determine its suitability for applications at room and higher temperatures. The microstructure manipulation mechanism, mechanical properties and strengthening mechanism in manipulated Al-13Si-5Cu-0.6 Mg alloy were discussed. The Zr 55Cu 30Al 10Ni 5 amorphous alloy manipulator provides more nucleation sites in the formation of primary Si, Al Si eutectic and Al 2Cu. As a result, the optimal microstructure is composed of finer α-Al grains, Al 2 Cu and more rounded primary and eutectic Si, with sizes decreased to ∼52%, 13%, 73% and 42%, respectively. The yield strength, tensile strength, elongation and fracture strain of manipulated Al-13Si-5Cu-0.6 Mg alloy are improved by 22.9%, 16.8%, 58.2% and 47.7% at room temperature than those of the unmanipulated Al-13Si-5Cu-0.6 Mg alloy, respectively. The improved tensile properties at room temperature are attributed to the significant strengthening effect of smaller precipitates and grain refinement while the excellent plasticity is derived from finer α-Al grain, round-corner primary Si and eutectic Si spheroidization. The yield strength and tensile strength are increased by 28.1% and 15.3% at 250 °C, and 28.3% and 10.8% at 300 °C, respectively. The strengthening mechanism at high temperature is mainly the second phase strengthening and the effect of finer eutectic Si on the pinning grain boundary. The overall microstructure manipulation in this work provides better comprehensive mechanical properties and a practicable method to fabricate the Al-Si-Cu-Mg alloy with superior strength and ductility, especially for die-casting alloy with short-time and high-efficiency.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. In situ synthesizing SiC particles and its strengthening effect on an Al–Si–Cu–Ni–Mg piston alloy10.1016/j.jallcom.2016.10.170 ↗
2. Influence of trace Zr on the microstructure and high temperature properties of an Al–Si–Cu–Ni–mg piston alloy10.1088/2053-1591/ab06ed ↗
3. Peritectic reaction between two primary Mn rich phases during solidification of Al-Si-cu-Mn heat-resistant alloy and the effect of cooling rate on it10.1016/j.jallcom.2018.04.199 ↗
4. Outstanding tensile ductility in high iron-containing Al-Si-cu alloys10.1007/s11661-020-05744-x ↗
5. Effect of d-Al3CuNi phase and thermal exposure on microstructure and mechanical properties of Al-Si-Cu-Ni alloys10.1016/j.jallcom.2019.03.412 ↗
6. Effect of eutectic Si size on the flow behavior and hot processing map of near eutectic Al-Si alloysJ10.1016/j.jmrt.2021.11.015 ↗
7. Effect of Zr on the high cycle fatigue and mechanical properties of Al–Si–Cu–Mg alloys at high temperatures10.1016/j.jallcom.2019.151795 ↗
8. Grain refinement and superplastic behavior of carbon nanotube reinforced aluminum alloy composite processed by cold rolling10.1016/j.msea.2017.10.031 ↗
9. Effect of constraint factor on the thermo-mechanical fatigue behavior of an Al-Si eutectic alloy
10. Cr-induced morphology change of primary Mn-rich phase in Al-Si-Cu-Mn heat resistant aluminum alloys and its contribution to high temperature strength10.1016/j.msea.2017.10.049 ↗
11. Aluminum alloy for internal-combustion piston, and aluminum alloy piston
12. Effects of Nd on microstructure and mechanical properties of cast Al-Si-Cu-Ni-Mg piston alloys10.1016/j.jallcom.2016.10.300 ↗
13. Structure and properties of cast Al-Si based alloy with Zr-V-Ti additions and its evaluation of high temperature performance10.1016/j.jallcom.2013.11.209 ↗
14. Evolution of nickel-rich phases in Al-Si-Cu-Ni-Mg piston alloys with different cu additions10.1016/j.matdes.2011.06.058 ↗
15. Insight into solidification microstructure control by trace TiCN–TiB2 particles for yielding fine-tuned nanoprecipitates in a hypoeutectic Al–Si–mg alloy10.1016/j.msea.2021.142093 ↗
16. Investigation on the elevated-temperature tribological behaviors and mechanism of Al-Cu-Mg composites reinforced by in-situ size-tunable TiB2-TiC particles10.1016/j.triboint.2022.107943 ↗
17. Modification of eutectic Si in Al–Si alloys with Eu addition10.1016/j.actamat.2014.10.064 ↗
18. Refinement of eutectic Si phase in Al-5Si alloys with Yb additions10.1007/s11661-012-1410-3 ↗
19. Multiscale design of α-Al, eutectic silicon and Mg2Si phases in Al-Si-mg alloy manipulated by in situ nanosized crystals10.1016/j.msea.2020.140627 ↗
20. A new approach to designing a grain refiner for mg casting alloys and its use in mg–Y-based alloys10.1016/j.actamat.2009.03.011 ↗
21. S, Nafisi, some remarks on cooling curves as a principle tool for solidification characterization10.1016/j.jcrysgro.2016.10.071 ↗
22. Simultaneously increasing strength and ductility of the Al–Cu alloys inoculated by Zr-based metallic glass10.1016/j.matchar.2014.12.016 ↗
23. Two quite different primary Mn-rich phases in Al–Si–Cu–Mn heat-resistant alloy and its effect to mechanical properties10.1016/j.msea.2018.05.100 ↗
24. Effect of ε-Al3Ni phase on mechanical properties of Al–Si–Cu–Mg–Ni alloys at elevated temperature10.1016/j.msea.2019.138794 ↗
25. A novel heat-resistant Al–Si–Cu–Ni–Mg base material synergistically strengthened by Ni-rich intermetallics and nano-AlNp microskeletons10.1016/j.jmst.2018.09.051 ↗
26. Microstructure and mechanical properties of Al–Si eutectic alloy modified with Al–3P master alloy10.1016/j.jmatprotec.2017.12.008 ↗
27. Influence of mg addition and T6 heat treatment on microstructure, mechanical and tribological properties of Al−12Si−3Cu based alloy10.1016/S1003-6326(21)65649-2 ↗
28. Effect of Q-Al5Cu2Mg8Si6 phase on mechanical properties of Al-Si-Cu-Mg alloy at high temperature10.1016/j.msea.2017.03.087 ↗
29. High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB2 particles10.1016/j.msea.2015.03.021 ↗
30. Influence of Gd content on microstructure and mechanical properties of cast Al–12Si–4Cu–2Ni–0.8Mg alloys10.1016/j.jallcom.2015.04.164 ↗
31. Microstructure, tensile properties and creep behavior of Al-12Si-3.5Cu-2Ni-0.8Mg alloy produced by different casting technologies10.1016/j.jmst.2017.06.011 ↗
32. Elevated temperature mechanical properties and fracture behaviors of the bond zone of aluminum matrix composites (Al-12Si/ABOw) with Al-12Si alloys10.1016/j.msea.2017.05.116 ↗
33. Amit Shyam, effect of grain-boundary θ-Al2Cu precipitates on tensile and compressive creep properties of cast Al–Cu–Mn–Zr alloys10.1016/j.msea.2022.142946 ↗
34. Cavitation-resistant intergranular precipitates enhance creep performance of θ’-strengthened Al-Cu based alloys10.1016/j.actamat.2022.117788 ↗
35. Improvement in as-cast strength of high pressure die-cast Al–Si–Cu–Mg alloys by synergistic effect of Q-Al5Cu2Mg8Si6 and θ-Al2Cu phases10.1016/j.msea.2020.140612 ↗
36. Synthesis and characterization of high performance low volume fraction TiC reinforced mg nanocomposites targeting biocompatible/structural applications10.1016/j.msea.2015.01.007 ↗
37. Processing, multiscale microstructure refinement and mechanical property enhancement of hypoeutectic Al–Si alloys via in situ bimodal-sized TiB2 particles10.1016/j.msea.2020.139081 ↗
38. Ultrasound-assisted dispersion of TiB2 nanoparticles in 7075 matrix hybrid composites10.1016/j.msea.2022.142958 ↗
39. Deformation behavior and strengthening mechanisms in a CNT-reinforced bimodal-grained aluminum matrix nanocomposite10.1016/j.msea.2021.141370 ↗
40. Consideration of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites: a model for predicting their yield strength10.1016/j.scriptamat.2005.12.017 ↗
41. Joining of dissimilar metals between magnesium AZ31B and aluminum A6061-T6 using galvanized steel as a transition joining layer10.1007/s42243-021-00589-z ↗
42. Properties and structure of a new non-reactive mold flux for high-Al steel10.1007/s42243-021-00708-w ↗
43. Hot compressive deformation of eutectic Al–17at% Cu alloy on the interface of the Cu–Al composite plate produced by horizontal continuous casting10.1007/s12613-021-2276-4 ↗
44. Microstructural heterogeneity and bonding strength of planar interface formed in additive manufacturing of Al–Mg–Si alloy based on friction and extrusionInt