Aging behavior and mechanical properties of ultra-fine grained Al2024-2TiN composite prepared by spark plasma sintering
Source abstract
Abstract
Abstract 2 wt%TiN nanoparticles reinforced ultra-fined grain Al2024 composite (Al2024-2TiN) and ultra-fined grain Al2024 alloy were prepared by high-energy ball milling, spark plasma sintering (SPS), and hot compression deformation. The effect of TiN nanoparticles on aging behavior and mechanical properties of Al2024-2TiN composite was investigated. The results show that, with the introduction of TiN nanoparticles, the tensile strength of as-aged Al2024-2TiN composite increased from 568 MPa of Al2024 alloy to 783 MPa, while the yield strength and elongation decreased from 376.5 MPa and 12.7% to 359.1 MPa and 9.4%, respectively. The average grain size of as-aged Al2024-2TiN composite was 452.4 nm, smaller than 3.2 μm of Al2024 alloy. TiN nanoparticles reduced the dissolution of the second phases during solution treatment, and decreased the number of age precipitating phases which resulted in the yield strength of Al2024-2TiN composite being lower than that of Al2024 alloy. Nevertheless, TiN nanoparticles promoted the aging kinetics of Al2024-2TiN composite. The peak aging time of 6 h for Al2024-2TiN composite was 2 h earlier than that of Al2024 alloy. The thermal diffusion activation energies of phase S′ precipitated in Al2024-2TiN composite and Al2024 alloy were 78.98 kJ/mol and 82.06 kJ/mol, respectively. Phase S′ precipitation in Al2024-TiN composite became easier.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: effects of SiC nanoparticles addition and heat treatment10.1016/j.matchar.2020.110827 ↗
2. Fabrication of a high strength ultra-fine grained Al-mg-SiC nanocomposite by multi-step friction-stir processing10.1016/j.msea.2017.05.065 ↗
3. Comparative studies on microstructural evolution, mechanical properties and room temperature dry sliding tribological behavior of nano-crystalline Al5083 alloy produced by the cryobox technique10.1088/2053-1591/ab3163 ↗
4. Mechanical and functional properties of ultrafine grained Al wires reinforced by nano-Al2O3 particles10.1016/j.matdes.2014.07.052 ↗
5. Solid state processing of aluminum matrix composites reinforced with nanoparticulate materials10.1002/adem.201800401 ↗
6. Microstructural features and mechanical properties of Al 5083/SiCp metal matrix nanocomposites produced by high energy ball milling and spark plasma sintering10.1016/j.msea.2012.02.095 ↗
7. Influence of microstructure and strengthening mechanism of AlMg5-Al2O3 nanocomposites prepared via spark plasma sintering10.1016/j.matdes.2016.01.138 ↗
8. Effect of SiC nanoparticles on the precipitation behavior and mechanical properties of 7075Al alloy10.1007/s10853-020-04381-4 ↗
9. Influence of aging treatment on the microstructure and mechanical properties of CNTs/7075 Al composites10.1016/j.jallcom.2019.152357 ↗
10. Heat treatment behavior and strengthening mechanisms of CNT/6061A1 composites fabricated by flake powder metallurgy10.1016/j.matchar.2019.05.017 ↗
11. Ageing behaviour of A356 alloy reinforced with in-situ formed TiB2 particles10.1016/j.msea.2008.01.042 ↗
12. Aging and thermal expansion behavior of Si3N4p/2024Al composite fabricated by pressure infiltration method10.1016/S1003-6326(11)61589-6 ↗
13. Preparation and mechanical properties of SiC-reinforced Al6061 composite by mechanical alloying10.1016/j.msea.2008.05.004 ↗
14. Aging behavior of a 2024 Al alloy-SiCp composite10.1016/j.matdes.2009.11.063 ↗
15. Aging behaviour of Al-cu-mg alloy-SiC composites10.1016/j.msea.2007.07.072 ↗
16. Precipitation phenomena in an ultrafine-grained Al alloy10.1016/j.actamat.2012.12.037 ↗
17. Effect of TiN nanoparticles on microstructure and properties of Al2024-TiN nanocomposite by high energy milling and spark plasma sintering10.1016/j.jallcom.2017.08.021 ↗
18. Character of the deformation bands in the (a + B) regime of the Portevin-Le Chatelier effect in Al-2.5%mg alloy10.1016/j.msea.2008.12.030 ↗
19. The effect of heat treatment on microstructure evolution in artificially aged carbon nanotube/Al2024 composites synthesized by mechanical alloying10.1016/j.matchar.2017.01.006 ↗
20. The solution treatment of in-situ sub-micron TiB2/2024 Al composite10.1016/j.matdes.2016.03.024 ↗
21. Microscopic examination of the interface region in 6061-Al/SiC composites reinforced with as-received and oxidized SiC particles10.1007/BF02646993 ↗
22. Interfacial microchemistry and microstructure of Al-mg-Si alloy matrix composites reinforced with Al2O3 particulates10.1016/S1359-6462(96)00467-8 ↗
23. Effect of alternative aging process on the fracture and interfacial properties of particulate Al2O3-reinforced Al (6061) metal matrix composite10.1007/s11661-002-0179-1 ↗
24. Characterization and strengthening mechanism of SiC nanoparticles reinforced magnesium matrix composite fabricated by ultrasonic vibration assisted squeeze casting
25. Precipitation Strengthening Model of AA 7055 Aluminium Alloy (in Chinese)
26. Effect of δ alumina fibers on the aging characteristics of 2024-based metal-matrix composites10.1007/BF02670599 ↗
27. Effect of reinforcement geometry on precipitation kinetics of powder metallurgy AA2009/SiC composites10.1016/j.jallcom.2008.12.114 ↗
28. Precipitation in 339 and 2124 aluminum: a caveat for calorimetry10.1023/A:1004837615783 ↗
29. Aging behavior of squeeze cast SiCw/AZ91 magnesium matrix composite10.1016/S0921-5093(02)00638-X ↗
30. Dislocation generation due to differences between the coefficients of thermal expansion10.1016/0025-5416(86)90261-2 ↗
31. Ageing behaviour of Al-cu-mg alloy matrix composites with SiCp of varying sizes10.1016/S1359-6462(97)00107-3 ↗
32. Comparison of the ageing behaviour of PM 2124 Al alloy and Al-SiCp metal-matrix composite10.1007/BF01171535 ↗
33. Analysis of strengthening in AA6111 during the early stages of aging: atom probe tomography and yield stress modelling10.1016/j.actamat.2013.08.033 ↗