Earthen construction: an increase of the mechanical strength by optimizing the dispersion of the binder phase
Source abstract
Abstract
Although of interest for its low embodied energy content for construction, earth is usually not used for modern construction due to the expensive, artisanal and complicated process and the high variability of the raw material. The transfer of techniques dedicated to cement concrete could help the industrialization of this material. The use of dispersant for an improved dispersion of the earth powder has been investigated for both dispersion of earth fine fraction and water (here named the binding phase) and mortar made with calibrated sand. An improvement of the rheology is observed with lower viscosity and yield stress. This leads to a very small improvement of the density however concomitant with a marked increase of the mechanical properties, Young modulus and compressive strength. The analysis of the microstructure of the mortar shows an increase of the largest pores, and a decrease of the clay platelets flocs. The evolutions of these properties are analyzed in terms of the Rumpf model at two different scales. The dispersant mainly acts on the platelet arrangement that defines the forces between particles, but also simultaneously decreases the permeability of this binding phase, therefore entrapping more air during the mixing of the powder and water. Clearly the use of a dispersant may be of interest for the processing of earth material on liquid state, decreasing the viscosity and/or allowing the reduction of the water content, and finally improving strength
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hygrothermal properties of building materials · Innovations in Concrete and Construction Materials · Geotechnical and construction materials studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Aïtcin P-C (2011) High performance concrete. CRC Press, New-York
2. Anderegg FO (1931) Grading aggregates-II.—the application of mathematical formulas to mortars. Ind Eng Chem 23:1058–106410.1021/ie50261a018 ↗
3. Andreasen A (1930) Ueber die Beziehung zwischen Kornabstufung und Zwischenraum in Produkten aus losen Körnern (mit einigen Experimenten). Kolloid-Zeitschrift 50:217–228. doi: 10.1007/BF0142298610.1007/BF01422986 ↗
4. Andreasen AM, Jensen W, Lundberg JJV (1929) Ein Apparat für die Dispersoidanalyse und einige Untersuchungen damit. Kolloid-Zeitschrift 49:253–265. doi: 10.1007/BF0142273210.1007/BF01422732 ↗
5. Andreola F, Castellini E, Ferreira J, Olhero S, Romagnoli M (2006) Effect of sodium hexametaphosphate and ageing on the rheological behaviour of kaolin dispersions. Appl Clay Sci 31:56–6410.1016/j.clay.2005.08.004 ↗
6. Arthur G (1955) Porosity and permeability changes during the sintering of copper powder. J Inst Met 83:329–336
7. Bergaya F, Theng BKG, Lagaly G (2011) Handbook of clay science. Elsevier, Oxford
8. Bowen P, Carry C, Luxembourg D, Hoffmann H (2005) Colloidal processing and sintering of nanosized transition aluminas. Powder Technol 157:100–107. doi: 10.1016/j.powtec.2005.05.01510.1016/j.powtec.2005.05.015 ↗
9. Buffiere J, Maire E, Adrien J, Masse J, Boller E (2010) In Situ experiments with X-ray tomography: an attractive tool for experimental mechanics. Exp Mech 50:289–305. doi: 10.1007/s11340-010-9333-710.1007/s11340-010-9333-7 ↗
10. Chatterji S (2001) A discussion of the paper “Mercury porosimetry—an inappropriate method for the measurement of pore size distributions in cement-based materials” by S. Diamond. Cem Concr Res 31:1657–165810.1016/S0008-8846(01)00618-4 ↗
11. Chen HYT, Wei WCJ, Hsu KC, Chen CS (2007) Adsorption of PAA on the alpha-Al2O3 surface. J Am Ceram Soc 90:1709–1716. doi: 10.1111/j.1551-2916.2007.01644.x10.1111/j.1551-2916.2007.01644.x ↗
12. Chiu R, Cima M (1993) Drying of granular ceramic films: II, drying stress and saturation uniformity. J Am Ceram Soc 76:2769–277710.1111/j.1151-2916.1993.tb04014.x ↗
13. Corradi A, Manfredini T, Pellacani G, Pozzi P (1994) Deflocculation of concentrated aqueous clay suspensions with sodium polymethacrylates. J Am Ceram Soc 77:509–51310.1111/j.1151-2916.1994.tb07022.x ↗
14. Cottrino S, Jorand Y, Adrien J, Olagnon C (2013) Spray-drying of highly concentrated nano alumina dispersions. Powder Technol 237:586–593. doi: 10.1016/j.powtec.2012.12.05810.1016/j.powtec.2012.12.058 ↗
15. Desset S, Spalla O, Lixon P, Cabanet B (2001) From powders to dispersions in water: effect of adsorbed molecules on the redispersion of alumina particles. Langmuir 17:6408–6418. doi: 10.1021/la010166t10.1021/la010166t ↗
16. Di Giuseppe E, D’Orazio M (2014) Moisture buffering “active” devices for indoor humidity control: preliminary experimental evaluations. Energy Procedia. 62:42–5110.1016/j.egypro.2014.12.365 ↗
17. Diamond S (2000) Mercury porosimetry : an inappropriate method for the measurement of pore size distributions in cement-based materials. Cem Concr Res 30:1517–152510.1016/S0008-8846(00)00370-7 ↗
18. Diamond S (2001) Reply to the discussion by S. Wild of the paper “Mercury porosimetry—an inappropriate method for the measurement of pore size distributions in cement-based materials” by S. Diamond. Cem Concr Res 31:1655–165610.1016/S0008-8846(01)00617-2 ↗
19. Doat P (1985) Construire en terre. Editions Alternatives, Paris
20. Gallé C (2001) Effect of drying on cement-based materials pore structure as identified by mercury intrusion porosimetry : a comparative study between oven-, vacuum-, and freeze-drying. Cem Concr Res 31:1467–147710.1016/S0008-8846(01)00594-4 ↗
21. Gelard D (2005) Identification et caractérisation de la cohésion interne du matériau terre dans ses conditions naturelles de conservation. Dissertation, INPG
22. Giesche H (2006) Mercury porosimetry: a general (practical) overview. Part Part Syst Charact 23:9–19. doi: 10.1002/ppsc.20060100910.1002/ppsc.200601009 ↗
23. Kendall K (1988) Agglomerate strength. Powder Metall 31:28–31
24. Kouakou CH, Morel JC (2009) Applied clay science. Appl Clay Sci 44:27–34. doi: 10.1016/j.clay.2008.12.01910.1016/j.clay.2008.12.019 ↗
25. Lagaly G (2005) From clay mineral crystals to colloidal clay mineral dispersions. Coagul Flocculation 2:519–60010.1201/9781420027686.ch8 ↗
26. Lagaly G, Ziesmer S (2003) Colloid chemistry of clay minerals: the coagulation of montmorillonite dispersions. Adv Colloid Interface Sci 100:105–12810.1016/S0001-8686(02)00064-7 ↗
27. Laribi S, Fleureau J-M, Grossiord J-L, Kbir-Ariguib N (2005) Comparative yield stress determination for pure and interstratified smectite clays. Rheol Acta 44:262–269. doi: 10.1007/s00397-004-0406-310.1007/s00397-004-0406-3 ↗
28. Lee H (1990) Validity of using mercury porosimetry to characterize the pore structures of ceramic green compacts. J Am Ceram Soc 73:2261–226510.1111/j.1151-2916.1990.tb07586.x ↗
29. Loginov M, Larue O, Lebovka N, Vorobiev E (2008) Fluidity of highly concentrated kaolin suspensions: influence of particle concentration and presence of dispersant. Colloid Surf A 325:64–71. doi: 10.1016/j.colsurfa.2008.04.04010.1016/j.colsurfa.2008.04.040 ↗
30. Moro F (2002) Ink-bottle effect in mercury intrusion porosimetry of cement-based materials. J Colloid Interface Sci 246:135–14910.1006/jcis.2001.7962 ↗
31. Naik TR (2008) Sustainability of concrete construction. Pract Period Struct Des Constr 3:98–10310.1061/(ASCE)1084-0680(2008)13:2(98) ↗
32. Nordby AS, Shea AD (2013) Building materials in the operational phase. J Ind Ecol 17:763–77610.1111/jiec.12046 ↗
33. Onoda GY, Hench LL, University of Florida (1978) Ceramic processing before firing. Wiley-Interscience, London
34. Quemada D (1998) Rheological modelling of complex fluids. I. The concept of effective volume fraction revisited. Eur Phys J AP 1:119–12710.1051/epjap:1998125 ↗
35. Rael R (2009) Earth Architecture. Architectural Press, Princeton
36. Rode C, Peuhkuri RH, Mortensen LH, Hansen KK et al (2005) Moisture buffering of building materials. Department of Civil Engineering, Technical University of Denmark, Kongens Lyngby
37. Rode C, Peuhkuri R, Hansen KK (2005) Moisture buffer value of materials in buildings. Presented at the seminar on moisture buffer capacity in August, pp 1–8
38. Santhiya D, Nandini G, Subramanian S, Natarajan K, Malghan S (1998) Effect of polymer molecular weight on the absorption of polyacrylic acid at the alumina–water interface. Colloid Surf A 133:157–16310.1016/S0927-7757(97)00132-5 ↗
39. Schubert H, Herrmann W, Rumpf H (1975) Deformation behaviour of agglomerates under tensile stress. Powder Technol 11:121–131. doi: 10.1016/0032-5910(75)80037-410.1016/0032-5910(75)80037-4 ↗
40. Studart AR, Amstad E, Gauckler LJ (2007) Colloidal stabilization of nanoparticles in concentrated suspensions. Langmuir 23:1081–1090. doi: 10.1021/la062042s10.1021/la062042s ↗
41. Tadros TF (2011) Rheology of dispersions. Wiley, Weinheim
42. Van Damme H, Zabat M, Laurent JP (2004) Nature and distribution of cohesive forces in earthen building materials. In: International conference on the conservation of grotto sites; motto grottoes, Dunhuang, pp 1–538
43. Webb P, Orr C (1997) Pore structure by mercury intrusion porosimetry (MIP). Analytical methods in fine particle technology. Micromeritics Instruments Corp., Norcross, pp 155–191
44. Xu L, Helstroom R, Scott O, Chambers AJ (1995) Fracture characteristics of powder compacts. Powder Technol 83:193–19910.1016/0032-5910(94)02958-Q ↗
45. Zaman A, Mathur S (2004) Influence of dispersing agents and solution conditions on the solubility of crude kaolin. J Colloid Interface Sci 271:124–13010.1016/j.jcis.2003.09.015 ↗
46. Zaman A, Tsuchiya R, Moudgil BM (2002) Adsorption of a low-molecular-weight polyacrylic acid on silica, alumina, and kaolin. J Colloid Interface Sci 256:73–78. doi: 10.1006/jcis.2001.794110.1006/jcis.2001.7941 ↗