journal article·2017-10Open access

Phase modification induced drying shrinkage reduction on Na2CO3 activated slag by incorporating Na2SO4

B. Yuan, Q. L. Yu, H. J. H. Brouwers

Materials and Structures· Volume 50· Issue 5

Abstract

This paper aims to study the phase modification, reaction kinetics, mechanical properties and drying shrinkage of sodium carbonate activated slag by incorporating sodium sulfate in the activator. The results show that the reaction process is firstly controlled by CO3 2− anions, and later runs similar to that of sodium sulfate activation. Besides, the relatively unstable phase gaylussite, commonly found in the sodium carbonate activation, is not observed in the reaction products upon hybrid activation, and monosulfoaluminate rather than ettringite is identified, probably caused by the reduced aluminate-to-sulfate ratio and increased pH value. The drying shrinkage is considerably reduced by up to 41% when replacing 50 wt% sodium carbonate by sodium sulfate, most possibly attributed to the induced phase modification. Furthermore, the relationships between the phase modification and drying shrinkage, and the potentially involved chemical reaction are discussed.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Concrete and Cement Materials Research · Magnesium Oxide Properties and Applications · CO2 Sequestration and Geologic Interactions

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (51)

Show source-provided references
1. Palomo A, Shi C, Jimenez AF (2011) New cements for the 21st century: the pursuit of an alternative to Portland cement. Cem Concr Res 41:750–763. doi: 10.1016/j.cemconres.2011.03.01610.1016/j.cemconres.2011.03.016 ↗
2. Provis JL, van Deventer JSJ (n.d) Alkali activated materials: state-of-the-art report. RILEM TC 224-AAM
3. Huiskes DMA, Keulen A, Yu QL, Brouwers HJH (2015) Design and performance evaluation of ultra-lightweight geopolymer concrete. Mater Des 89:516–526. doi: 10.1016/j.matdes.2015.09.16710.1016/j.matdes.2015.09.167 ↗
4. Shi C, Day RL (1996) Some factors affecting early hydration of alkali-slag cements. Cem Concr Res 26:439–447. doi: 10.1016/S0008-8846(96)85031-910.1016/S0008-8846(96)85031-9 ↗
5. Jimenez AF, Puertas F (2001) Setting of alkali-activated slag cement. Influence of activator nature. Adv Cem Res 13:115–121. doi: 10.1680/adcr.2001.13.3.11510.1680/adcr.2001.13.3.115 ↗
6. Gao X, Yu QL, Brouwers HJH (2015) Reaction kinetics, gel character and strength of ambient temperature cured alkali activated slag–fly ash blends. Constr Build Mater 80:105–115. doi: 10.1016/j.conbuildmat.2015.01.06510.1016/j.conbuildmat.2015.01.065 ↗
7. Rakhimova NR, Rakhimov RZ, Naumkina NI, Khuzin AF, Osin YN (2016) Influence of limestone content, fineness, and composition on the properties and microstructure of alkali-activated slag cement. Cem Concr Compos 72:268–274. doi: 10.1016/j.cemconcomp.2016.06.01510.1016/j.cemconcomp.2016.06.015 ↗
8. Gao X, Yu QL, Brouwers HJH (2015) Properties of alkali activated slag–fly ash blends with limestone addition. Cem Concr Compos 59:119–128. doi: 10.1016/j.cemconcomp.2015.01.00710.1016/j.cemconcomp.2015.01.007 ↗
9. Gao X, Yu QL, Brouwers HJH (2015) Characterization of alkali activated slag–fly ash blends containing nano-silica. Constr Build Mater 98:397–406. doi: 10.1016/j.conbuildmat.2015.08.08610.1016/j.conbuildmat.2015.08.086 ↗
10. Collins F, Sanjayan JG (1998) Early age strength and workability of slag pastes activated by NaOH and Na2CO3. Cem Concr Res 28:655–66410.1016/S0008-8846(98)00025-8 ↗
11. Yuan B, Yu QL, Brouwers HJH (2015) Reaction kinetics, reaction products and compressive strength of ternary activators activated slag designed by Taguchi method. Mater Des 86:878–886. doi: 10.1016/j.matdes.2015.07.07710.1016/j.matdes.2015.07.077 ↗
12. Bernal SA, San Nicolas R, Provis J, van Deventer JS (2015) Alkali-activated slag cements produced with a blended sodium carbonate/sodium silicate activator. Adv Cem Res. doi: 10.1680/adcr.15.0001310.1680/adcr.15.00013 ↗
13. Garcia-Lodeiro I, Fernández-Jiménez A (2015) 02—An overview of the chemistry of alkali-activated cement-based binders. In: Handbook of alkali-activated cements mortars and concretes. doi: 10.1533/9781782422884.1.1910.1533/9781782422884.1.19 ↗
14. Bernal SA, Nicolas RS, Myers RJ, Mejia De Gutierrez R, Puertas F, Van Deventer JSJ, Provis JL (2014) MgO content of slag controls phase evolution and structural changes induced by accelerated carbonation in alkali-activated binders. Cem Concr Res 57:33–43. doi: 10.1016/j.cemconres.2013.12.00310.1016/j.cemconres.2013.12.003 ↗
15. Bernal SA, Provis JL, Myers RJ, San Nicolas R, van Deventer JS (2014) Role of carbonates in the chemical evolution of sodium carbonate-activated slag binders. Mater Struct 48:517–529. doi: 10.1617/s11527-014-0412-610.1617/s11527-014-0412-6 ↗
16. Bernal SA (2016) Advances in near-neutral salts activation of blast furnace slags. RILEM Tech Lett 1:39–4410.21809/rilemtechlett.2016.8 ↗
17. Wang S, Scrivener KL, Pratt PL (1994) Factors affecting the strength of alkali-activated slag. Cem Concr Res 24:1033–104310.1016/0008-8846(94)90026-4 ↗
18. Jimenez A, Puertas F, Sobrados I, Sanz J (2003) Structure of calcium silicate hydrates formed in alkaline-activated slag: influence of the type of alkaline activator. J Am Ceram Soc 86:1389–1394. doi: 10.1111/j.1151-2916.2003.tb03481.x10.1111/j.1151-2916.2003.tb03481.x ↗
19. Moseson AJ, Moseson DE, Barsoum MW (2012) High volume limestone alkali-activated cement developed by design of experiment. Cem Concr Compos 34:328–336. doi: 10.1016/j.cemconcomp.2011.11.00410.1016/j.cemconcomp.2011.11.004 ↗
20. Yuan B, Straub C, Segers S, Yu QL, Brouwers HJ (2017) Sodium carbonate activated slag as cement replacement in autoclaved aerated concrete. Ceram Int 43:6039–6047. doi: 10.1016/j.ceramint.2017.01.14410.1016/j.ceramint.2017.01.144 ↗
21. Yuan B, Yu QL, Brouwers HJH (2017) Evaluation of slag characteristics on the reaction kinetics and mechanical properties of Na2CO3 activated slag. Constr Build Mater 131:334–346. doi: 10.1016/j.conbuildmat.2016.11.07410.1016/j.conbuildmat.2016.11.074 ↗
22. Jin F, Gu K, Al-Tabbaa A (2014) Strength and drying shrinkage of slag paste activated by sodium carbonate and reactive MgO. Constr Build Mater 81:58–65. doi: 10.1016/j.conbuildmat.2013.10.08110.1016/j.conbuildmat.2013.10.081 ↗
23. Yuan B, Yu QL, Dainese E, Brouwers HJH (2017) Autogenous and drying shrinkage of sodium carbonate activated slag altered by limestone powder incorporation. Constr Build Mater 153:459–468. doi: 10.1016/j.conbuildmat.2017.07.11210.1016/j.conbuildmat.2017.07.112 ↗
24. Yuan B, Yu QL, Brouwers HJH (2017) Assessing the chemical involvement of limestone powder in sodium carbonate activated slag. Mater Struct 50:13610.1617/s11527-017-1003-0 ↗
25. Yuan X, Chen W, Lu Z, Chen H (2014) Shrinkage compensation of alkali-activated slag concrete and microstructural analysis. Constr Build Mater 66:422–428. doi: 10.1016/j.conbuildmat.2014.05.08510.1016/j.conbuildmat.2014.05.085 ↗
26. Rashad AM, Bai Y, Basheer PAM, Milestone NB, Collier NC (2013) Hydration and properties of sodium sulfate activated slag. Cem Concr Compos 37:20–29. doi: 10.1016/j.cemconcomp.2012.12.01010.1016/j.cemconcomp.2012.12.010 ↗
27. Mobasher N, Bernal SA, Provis JL (2016) Structural evolution of an alkali sulfate activated slag cement. J Nucl Mater 468:97–104. doi: 10.1016/j.jnucmat.2015.11.01610.1016/j.jnucmat.2015.11.016 ↗
28. He J, Wei M, Li B, Kang Y, Evans DG, Duan X (2006) Preparation of layered double hydroxides. Layer Double Hydroxides 119:89–119. doi: 10.1007/430_00610.1007/430_006 ↗
29. Xu H, Provis JL, Van Deventer JSJ, Krivenko PV (2008) Characterization of aged slag concretes. ACI Mater J 105:131–139
30. Sheikholeslami R, Ng M (2001) Calcium sulfate precipitation in the presence of nondominant calcium carbonate: thermodynamics and kinetics. Ind Eng Chem Res 40:3570–3578. doi: 10.1021/ie000781c10.1021/ie000781c ↗
31. Ravikumar D, Neithalath N (2012) Reaction kinetics in sodium silicate powder and liquid activated slag binders evaluated using isothermal calorimetry. Thermochim Acta 546:32–43. doi: 10.1016/j.tca.2012.07.01010.1016/j.tca.2012.07.010 ↗
32. Ben Haha M, Lothenbach B, Le Saout G, Winnefeld F (2012) Influence of slag chemistry on the hydration of alkali-activated blast-furnace slag—Part II: Effect of Al2O3. Cem Concr Res 42:74–83. doi: 10.1016/j.cemconres.2011.08.00510.1016/j.cemconres.2011.08.005 ↗
33. Yu QL, Brouwers HJH (2012) Development of a self-compacting gypsum-based lightweight composite. Cem Concr Compos 34:1033–1043. doi: 10.1016/j.cemconcomp.2012.05.00410.1016/j.cemconcomp.2012.05.004 ↗
34. Yuan B, Yu QL, Brouwers HJH (2015) Time-dependent characterization of Na2CO3 activated slag. Cem Concr Compos (Under review)
35. Ke X, Bernal SA, Provis JL (2016) Controlling the reaction kinetics of sodium carbonate-activated slag cements using calcined layered double hydroxides. Cem Concr Res 81:24–37. doi: 10.1016/j.cemconres.2015.11.01210.1016/j.cemconres.2015.11.012 ↗
36. Whittaker M, Zajac M, Ben Haha M, Bullerjahn F, Black L (2014) The role of the alumina content of slag, plus the presence of additional sulfate on the hydration and microstructure of Portland cement-slag blends. Cem Concr Res 66:91–101. doi: 10.1016/j.cemconres.2014.07.01810.1016/j.cemconres.2014.07.018 ↗
37. Matschei T, Lothenbach B, Glasser FP (2007) The AFm phase in Portland cement. Cem Concr Res 37:118–130. doi: 10.1016/j.cemconres.2006.10.01010.1016/j.cemconres.2006.10.010 ↗
38. Pollmann Herbert (2010) Mineralisation of wastes and industrial residues. Shaker Verlag GmbH, Germany
39. Mobasher N, Bernal SA, Hussain OH, Apperley DC, Kinoshita H, Provis JL (2014) Characterisation of Ba(OH)2–Na2SO4-blast furnace slag cement-like composites for the immobilisation of sulfate bearing nuclear wastes. Cem Concr Res 66:64–74. doi: 10.1016/j.cemconres.2014.07.00610.1016/j.cemconres.2014.07.006 ↗
40. Puertas F, Carrasco MT (2014) Use of glass waste as an activator in the preparation of alkali-activated slag. Mechanical strength and paste characterisation. Cem Concr Res 57:95–104. doi: 10.1016/j.cemconres.2013.12.00510.1016/j.cemconres.2013.12.005 ↗
41. Abdalqader AF, Jin F, Al-Tabbaa A (2015) Characterisation of reactive magnesia and sodium carbonate-activated fly ash/slag paste blends. Constr Build Mater 93:506–513. doi: 10.1016/j.conbuildmat.2015.06.01510.1016/j.conbuildmat.2015.06.015 ↗
42. Garcia Lodeiro I, Macphee DE, Palomo A, Fernandez AJ (2009) Effect of alkalis on fresh C–S–H gels. FTIR analysis. Cem Concr Res 39:147–153. doi: 10.1016/j.cemconres.2009.01.00310.1016/j.cemconres.2009.01.003 ↗
43. Puertas F, Jimenez AF, Blanco-Varela MT (2004) Pore solution in alkali-activated slag cement pastes. Relation to the composition and structure of calcium silicate hydrate. Cem Concr Res 34:139–148. doi: 10.1016/S0008-8846(03)00254-010.1016/S0008-8846(03)00254-0 ↗
44. Palacios M, Puertas F (2006) Effect of carbonation on alkali-activated slag paste. J Am Ceram Soc 89:3211–3221. doi: 10.1111/j.1551-2916.2006.01214.x10.1111/j.1551-2916.2006.01214.x ↗
45. Rashad AM, Bai Y, Basheer PAM, Collier NC, Milestone NB (2012) Chemical and mechanical stability of sodium sulfate activated slag after exposure to elevated temperature. Cem Concr Res 42:333–343. doi: 10.1016/j.cemconres.2011.10.00710.1016/j.cemconres.2011.10.007 ↗
46. Ye H, Radlinska A (2016) Shrinkage mechanisms of alkali-activated slag. Cem Concr Res 88:126–135. doi: 10.1016/j.cemconres.2016.07.00110.1016/j.cemconres.2016.07.001 ↗
47. Gao X, Yu QL, Brouwers HJH (2016) Assessing the porosity and shrinkage of alkali activated slag-fly ash composites designed applying a packing model. Constr Build Mater 119:175–184. doi: 10.1016/j.conbuildmat.2016.05.02610.1016/j.conbuildmat.2016.05.026 ↗
48. Bontchev RP, Liu S, Krumhansl JL, Voigt J, Nenoff TM (2003) Synthesis, characterization, and ion exchange properties of hydrotalcite Mg6Al2(OH)16(A) x (A′)−x , 4H2O (A, A′ = Cl−, Br−, I−, and NO3−, 2 > x > 0) derivatives. Chem Mater 15:3669–367510.1021/cm034231r ↗
49. Clark B, Brown P (1999) The formation of calcium sulfoaluminate hydrate compounds. Part I. Cem Concr Res 29:1943–1948. doi: 10.1016/S0008-8846(99)00200-810.1016/S0008-8846(99)00200-8 ↗
50. Clark BA, Brown PW (2000) Formation of calcium sulfoaluminate hydrate compounds. Part II. Cem Concr Res 30:1943–1948. doi: 10.1016/S0008-8846(99)00234-310.1016/S0008-8846(99)00234-3 ↗
51. Gabrisova A, Havlica J, Sahu S (1991) Stability of calcium sulphoaluminate hydrates in water solutions with various pH values. Cem Concr Res 21:1023–1027. doi: 10.1016/0008-8846(91)90062-M10.1016/0008-8846(91)90062-M ↗