Impact of cracks on distribution of chloride-induced reinforcement corrosion
Source abstract
Abstract
Abstract Surface crack width is regulated in codes to limit corrosion of reinforcement bars in concrete. However, the influence of surface crack width on corrosion damages is not directly inferable from previous research.In this work, data on corroded cracked concrete specimens in chloride environments was compiled. Detailed information was included, such as crack and pit locations, local corrosion pattern, etc. Five hypotheses on the influence of transversal cracks on corrosion damage were formulated, and statistical methods were used to test them on the dataset.Transversal cracks were good indicators of the position of corrosion pits. The corrosion rate of the pit increased in proximity of a crack. With time, pits grew in depth at a slower rate but increased in number. No clear correlation between surface crack width and corrosion damage was found. Results point out discrepancies in the collected data, arguing for the need of well-defined procedures for assessing crack and corrosion damage.Further, the statistical treatment allowed for identification of bias in existing data, which was used as a research planning tool to provide guidance on the design of additional experiments. Thus, recommendations for future experimental work required to reduce the bias are given.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Concrete Corrosion and Durability · Concrete and Cement Materials Research · Corrosion Behavior and Inhibition
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (73)
Show source-provided references
1. Bell B (2004) European Railway Bridge Problems. Sustain brid 1:3
2. Andrade C (2018) Some historical notes on the research in corrosion of reinforcement. Hormigón y Acero 69:21–28. https://doi.org/10.1016/j.hya.2018.12.00210.1016/j.hya.2018.12.002 ↗
3. Tuutti K (1982) Corrosion of steel in concrete. Tech. rep, Swedish Cement and Concrete Research Institute, Stockholm
4. Beeby AW (1979) Prediction of crack widths in hardened concrete. Struct Eng 57A(1):9–17
5. Haynes HH, Abolitz AL, Anderson AR, Boaz I, Boyd AD, Cichanski WJ, Clarke J, Dobrowolski JA, Duncan JM, Litton RW, Mattock AH, Runge KH, Smith CE, Smith RJ, Stiansen SG, Yee AA, Monnier TH Guide for the Design and Construction of Fixed Offshore Concrete Structures. https://doi.org/10.14359/1051610.14359/10516 ↗
6. CEN, EN 1992-1-1:2004: E, (2004). http://link.springer.com/10.1007/978-3-642-41714-6_51753
7. Käthler CB, Angst UM, Hornbostel K, Elsener B (2020) Critical analysis of experiments on reinforcing bar corrosion in cracked concrete. ACI Mater J 117(3):145–154. https://doi.org/10.14359/5172240810.14359/51722408 ↗
8. Chen E, Berrocal CG, Löfgren I, Lundgren K (2020) Correlation between concrete cracks and corrosion characteristics of steel reinforcement in pre-cracked plain and fibre-reinforced concrete beams. Mater Struct Mater Construct 53(2):1–22. https://doi.org/10.1617/s11527-020-01466-z10.1617/s11527-020-01466-z ↗
9. Jiménez-Quero V, Montes-García P, Bremner T (2010) Influence of concrete cracking on the corrosion of steel reinforcement, 2010 concrete under Severe Conditions: Environment and Loading - Proceedings of the 6th International Conference on Concrete under Severe Conditions, pp. 383–38910.1201/b10552-46 ↗
10. Mohammed TU, Otsuki N, Hisada M, Shibata T (2001) Effect of crack width and bar types on corrosionof steel in concrete. J Mater Civ Eng 13(3):194–201. https://doi.org/10.1061/(asce)0899-1561(2001)13:3(194)10.1061/(asce)0899-1561(2001)13:3(194) ↗
11. Boschmann Kathler A, Angst U, Wagner M, Larsen C, Elsener B (2017) Effect of cracks on chloride- induced corrosion of steel in concrete - a review. Int Corros Process 41:1–23
12. Danner T, Jakobsen UH, Geiker MR (2019) Mineralogical sequence of self-healing products in cracked marine concrete. Minerals 9(5):284–289. https://doi.org/10.3390/min905028410.3390/min9050284 ↗
13. Angst UM, Geiker MR, Alonso MC, Polder R, Isgor OB, Elsener B, Wong H, Michel A, Hornbostel K, Gehlen C, François R, Sanchez M, Criado M, Sørensen H, Hansson C, Pillai R, Mundra S, Gulikers J, Raupach M, Pacheco J, Sagüés A The effect of the steel-concrete interface on chloride-induced corrosion initiation in concrete: a critical review by RILEM TC 262-SCI, Materials and Structures/Materiaux et Constructions 52(4). https://doi.org/10.1617/s11527-019-1387-010.1617/s11527-019-1387-0 ↗
14. Lopez-Calvo HZ, Montes-García P, Jiménez-Quero VG, Gómez-Barranco H, Bremner TW, Thomas MD (2018) Influence of crack width, cover depth and concrete quality on corrosion of steel in HPC containing corrosion inhibiting admixtures and fly ash. Cement Concrete Compos 88:200–210. https://doi.org/10.1016/j.cemconcomp.2018.01.01610.1016/j.cemconcomp.2018.01.016 ↗
15. Geiker M, Danner T, Michel A, Belda Revert A, Linderoth O, Hornbostel K (2021) 25 Years of field exposure of pre-cracked concrete beams; combined impact of spacers and cracks on reinforcement corrosion. Construct Build Mater 286:122–801. https://doi.org/10.1016/j.conbuildmat.2021.12280110.1016/j.conbuildmat.2021.122801 ↗
16. Blagojevic A (2016) The Influence of Cracks on the Durability and Service Life of Reinforced Concrete Structures in relation to Chloride-Induced Corrosion, Ph.D. thesis
17. Šavija B, Schlangen E (2016) Autogeneous healing and chloride ingress in cracked concrete. Heron 61(1):15–32
18. Danner T, Geiker MR (2018) Long-term influence of concrete surface and crack orientation on self-healing and ingress in cracks - field observations. Nordic Concrete Res 58(1):1–16. https://doi.org/10.2478/ncr-2018-000110.2478/ncr-2018-0001 ↗
19. Tammo K, Thelandersson S (2009) Crack widths near reinforcement bars for beams in bending. Struct Concrete 10(1):27–34. https://doi.org/10.1680/stco.2009.10.1.2710.1680/stco.2009.10.1.27 ↗
20. Yu L, François R, Dang VH, L’Hostis V, Gagné R (2015) Development of chloride-induced corrosion in pre-cracked RC beams under sustained loading: effect of load-induced cracks, concrete cover, and exposure conditions. Cement Concrete Res 67:246–258. https://doi.org/10.1016/j.cemconres.2014.10.00710.1016/j.cemconres.2014.10.007 ↗
21. Otieno M, Beushausen H, Alexander M (2012) Towards incorporating the influence of cover cracking on steel corrosion in RC design codes: the concept of performance-based crack width limits. Mater Struct Mater Construct 45(12):1805–1816. https://doi.org/10.1617/s11527-012-9871-910.1617/s11527-012-9871-9 ↗
22. Pease BJ, Geiker MR (2018) Durability-related crack width and concrete cover requirements and recommendations from reinforced concrete design codes., Tech. rep., Department of Structural Engineering NTNU
23. Hornbostel K, Geiker MR (2017) Influence of cracking on reinforcement corrosion. In: the nordic concrete federation. Oslo, London pp 53–59
24. Bertolini L, Elsener B, Pedeferri P, Polder R (2004) Corrosion of steel in Concrete. Repair., Weinheiim, Germany, Prevention, Diagnosis
25. Tammo K, Thelandersson S (2006) Crack opening near reinforcement bars in concrete structures. Struct Concrete 7(4):137–143. https://doi.org/10.1680/stco.2006.7.4.13710.1680/stco.2006.7.4.137 ↗
26. Michel A, Solgaard AO, Pease BJ, Geiker MR, Stang H, Olesen JF (2013) Experimental investigation of the relation between damage at the concrete-steel interface and initiation of reinforcement corrosion in plain and fibre reinforced concrete. Corros Sci 77:308–321. https://doi.org/10.1016/j.corsci.2013.08.01910.1016/j.corsci.2013.08.019 ↗
27. Schießl P, Raupach M (1997) Laboratory studies and calculations on the influence of crack width on chloride-induced corrosion of steel in concrete. ACI Mater J 94(1):56–62. https://doi.org/10.14359/28510.14359/285 ↗
28. Li W, Liu W, Wang S (2017) The effect of crack width on chloride-induced corrosion of steel in concrete. Adv Mater Sci Eng. https://doi.org/10.1155/2017/396857810.1155/2017/3968578 ↗
29. François R, Arliguie G (1999) Effect of microcracking and cracking on the development of corrosion in reinforced concrete members. Magaz Concrete Res 51(2):143–150. https://doi.org/10.1680/macr.1999.51.2.14310.1680/macr.1999.51.2.143 ↗
30. François R, Khan I, Vu NA, Mercado H, Castel A (2012) Study of the impact of localised cracks on the corrosion mechanism. Europ J Environ Civ Eng 16(3–4):392–401. https://doi.org/10.1080/19648189.2012.66798210.1080/19648189.2012.667982 ↗
31. Tammo K, Thelandersson S (2009) Crack behavior near reinforcing bars in concrete structures. ACI Struct J 106(3):259–267
32. Pease B, Geiker M, Stang H, Weiss J (2011) The design of an instrumented rebar for assessment of corrosion in cracked reinforced concrete. Mater Struct Mater Construct 44(7):1259–1271. https://doi.org/10.1617/s11527-010-9698-110.1617/s11527-010-9698-1 ↗
33. Otieno M, Beushausen H, Alexander M (2016) Chloride-induced corrosion of steel in cracked concrete - part I: experimental studies under accelerated and natural marine environments. Cement Concrete Res 79:373–385. https://doi.org/10.1016/j.cemconres.2015.08.00910.1016/j.cemconres.2015.08.009 ↗
34. Scott A, Alexander MG (2007) The influence of binder type, cracking and cover on corrosion rates of steel in chloride-contaminated concrete. Magaz Conc Res 59(7):495–505. https://doi.org/10.1680/macr.2007.59.7.49510.1680/macr.2007.59.7.495 ↗
35. Otieno MB, Alexander MG, Beushausen HD (2010) Corrosion in cracked and uncracked concrete - influence of crack width, concrete quality and crack reopening. Magaz Concrete Res 62(6):393–404. https://doi.org/10.1680/macr.2010.62.6.39310.1680/macr.2010.62.6.393 ↗
36. Alexander MG, Beushausen H, Otieno MB (2012) Research Monograph no 9: corrosion of steel in reinforced concrete: influence of binder type, water/binder ratio, cover and cracking, department of civil engineering. Univ Cape Town Concrete Mater Struct Integr Res Unit (CoMSIRU) 10(9):4–32
37. Jaffer SJ (2007) The influence of loading on the corrosion of steel in cracked ordinary portland cement and high performance concretes, Ph.D. thesis10.1016/j.corsci.2008.09.018 ↗
38. Poursaee A, Hansson CM (2009) Potential pitfalls in assessing chloride-induced corrosion of steel in concrete. Cement Concrete Res 39(5):391–400. https://doi.org/10.1016/j.cemconres.2009.01.01510.1016/j.cemconres.2009.01.015 ↗
39. Francois R, Arliguie G, Bardy D (1994) Electrode potential measurements of concrete reinforcement for corrosion evaluation. Cement Concrete Res 24(3):401–412. https://doi.org/10.1016/0008-8846(94)90127-910.1016/0008-8846(94)90127-9 ↗
40. Francois R, Maso J (1988) Effect of damage in reinforced concrete on carbonation or chloride penetration. Cement Concrete Compos 18(6):961–970
41. Yu L, François R, Dang VH, L’Hostis V, Gagné R (2015) Structural performance of RC beams damaged by natural corrosion under sustained loading in a chloride environment. Eng Struct 96:30–40. https://doi.org/10.1016/j.engstruct.2015.04.00110.1016/j.engstruct.2015.04.001 ↗
42. Zhang W, Yu L, François R (2019) Influence of top-casting-induced defects on the corrosion of the compressive reinforcement of naturally corroded beams under sustained loading. Construct Build Mater 229:116912. https://doi.org/10.1016/j.conbuildmat.2019.11691210.1016/j.conbuildmat.2019.116912 ↗
43. Zhang W, François R, Yu L (2020) Influence of load-induced cracks coupled or not with top-casting-induced defects on the corrosion of the longitudinal tensile reinforcement of naturally corroded beams exposed to chloride environment under sustained loading. Cement Concrete Res 129(January):105972. https://doi.org/10.1016/j.cemconres.2020.10597210.1016/j.cemconres.2020.105972 ↗
44. Zhu W, François R, Zhang C, Zhang D (2018) Propagation of corrosion-induced cracks of the RC beam exposed to marine environment under sustained load for a period of 26 years. Cement Concrete Res 103(April 2017):66–76. https://doi.org/10.1016/j.cemconres.2017.09.01410.1016/j.cemconres.2017.09.014 ↗
45. Zhu W, François R, Liu Y (2017) Propagation of corrosion and corrosion patterns of bars embedded in RC beams stored in chloride environment for various periods. Construct Build Mater 145:147–156. https://doi.org/10.1016/j.conbuildmat.2017.03.21010.1016/j.conbuildmat.2017.03.210 ↗
46. Zhu W, François R (2014) Corrosion of the reinforcement and its influence on the residual structural performance of a 26-year-old corroded RC beam. Construct Build Mater 51:461–472. https://doi.org/10.1016/j.conbuildmat.2013.11.01510.1016/j.conbuildmat.2013.11.015 ↗
47. Zhu W, François R, Coronelli D, Cleland D (2013) Effect of corrosion of reinforcement on the mechanical behaviour of highly corroded RC beams. Eng Struct 56:544–554. https://doi.org/10.1016/j.engstruct.2013.04.01710.1016/j.engstruct.2013.04.017 ↗
48. Zhang R, Castel A, François R (2010) Concrete cover cracking with reinforcement corrosion of RC beam during chloride-induced corrosion process. Cement Concrete Res 40(3):415–425. https://doi.org/10.1016/j.cemconres.2009.09.02610.1016/j.cemconres.2009.09.026 ↗
49. Castel A, François R, Arliguie G (2000) Mechanical behaviour of corroded reinforced concrete beams - Part 1: experimental study of corroded beams. Mater Struct Materi Construct 33(9):539–544. https://doi.org/10.1007/bf0248053310.1007/bf02480533 ↗
50. Castel A, Vidal T, François R, Arliguie G (2003) Influence of steel - concrete interface quality on reinforcement corrosion induced by chlorides. Magaz Concrete Res 55(2):151–159. https://doi.org/10.1680/macr.2003.55.2.15110.1680/macr.2003.55.2.151 ↗
51. Zhang R, Castel A, François R (2009) Serviceability Limit State criteria based on steel-concrete bond loss for corroded reinforced concrete in chloride environment. Mater Struct Mater Construct 42(10):1407–1421. https://doi.org/10.1617/s11527-008-9460-010.1617/s11527-008-9460-0 ↗
52. Yu L, François R, Gagné R (2018) Mechanical performance of deep beams damaged by corrosion in a chloride environment. Europ J Environ Civ Eng 22(5):523–545. https://doi.org/10.1080/19648189.2016.121003310.1080/19648189.2016.1210033 ↗
53. Vidal T, Castel A, François R (2004) Analyzing crack width to predict corrosion in reinforced concrete. Cement Concrete Res 34(1):165–174. https://doi.org/10.1016/S0008-8846(03)00246-110.1016/S0008-8846(03)00246-1 ↗
54. Vidal T, Castel A, François R (2007) Corrosion process and structural performance of a 17 year old reinforced concrete beam stored in chloride environment. Cement Concrete Res 37(11):1551–1561. https://doi.org/10.1016/j.cemconres.2007.08.00410.1016/j.cemconres.2007.08.004 ↗
55. François R, Castel A, Vidal T, Vu NA (2006) Long term corrosion behavior of reinforced concrete structures in chloride environnement. J De Phys IV JP 136:285–293. https://doi.org/10.1051/jp4:200613602910.1051/jp4:2006136029 ↗
56. Khan I, François R, Castel A (2014) Prediction of reinforcement corrosion using corrosion induced cracks width in corroded reinforced concrete beams. Cement Concrete Res 56:84–96. https://doi.org/10.1016/j.cemconres.2013.11.00610.1016/j.cemconres.2013.11.006 ↗
57. Khan I, François R, Castel A (2012) Structural performance of a 26-year-old corroded reinforced concrete beam. Europ J Environ Civ Eng 16(3–4):440–449. https://doi.org/10.1080/19648189.2012.66799210.1080/19648189.2012.667992 ↗
58. François R, Khan I, Dang VH (2013) Impact of corrosion on mechanical properties of steel embedded in 27-year-old corroded reinforced concrete beams. Mater Struct Mater Construct 46(6):899–910. https://doi.org/10.1617/s11527-012-9941-z10.1617/s11527-012-9941-z ↗
59. Dang VH, François R (2014) Prediction of ductility factor of corroded reinforced concrete beams exposed to long term aging in chloride environment. Cement Concrete Compos 53:136–147. https://doi.org/10.1016/j.cemconcomp.2014.06.00210.1016/j.cemconcomp.2014.06.002 ↗
60. François R, Arliguie G (1998) Influence of service cracking on reinforcement steel corrosion. J Mater Civ Eng 10(1):14–20. https://doi.org/10.1061/(asce)0899-1561(1998)10:1(14)10.1061/(asce)0899-1561(1998)10:1(14) ↗
61. Zhang W, François R, Yu L (2020) Influence of load-induced cracks coupled or not with top-casting-induced defects on the corrosion of the longitudinal tensile reinforcement of naturally corroded beams exposed to chloride environment under sustained loading. Cement Concrete Res 129(January):105972. https://doi.org/10.1016/j.cemconres.2020.10597210.1016/j.cemconres.2020.105972 ↗
62. Chen E, Berrocal CG, Fernandez I, Löfgren I, Lundgren K (2020) Assessment of the mechanical behaviour of reinforcement bars with localised pitting corrosion by digital image correlation. Eng Struct 219(June):110936. https://doi.org/10.1016/j.engstruct.2020.11093610.1016/j.engstruct.2020.110936 ↗
63. Edvardsen C (1999) Water permeability and autogenous healing of cracks in concrete. ACI Mater J 96(4):448–454. https://doi.org/10.14359/64510.14359/645 ↗
64. Berrocal CG, Löfgren I, Lundgren K (2018) The effect of fibres on steel bar corrosion and flexural behaviour of corroded RC beams. Eng Struct 163(May 2017):409–425. https://doi.org/10.1016/j.engstruct.2018.02.06810.1016/j.engstruct.2018.02.068 ↗
65. Zhu W, François R (2015) Structural performance of RC beams in relation with the corroded period in chloride environment. Mater Struct Mater Construct 48(6):1757–1769. https://doi.org/10.1617/s11527-014-0270-210.1617/s11527-014-0270-2 ↗
66. Lee Rodgers J, Alan Nice Wander W (1988) Thirteen ways to look at the correlation coefficient. Am Statist 42(1):59–66. https://doi.org/10.1080/00031305.1988.1047552410.1080/00031305.1988.10475524 ↗
67. Chen PY, Popovich PM (2011) Correlation: parametric and nonparametric measures. https://doi.org/10.4135/9781412983808.n110.4135/9781412983808.n1 ↗
68. Taylor JR (1997) An introduction to error analysis. University science books, New Jersey
69. Box GEP, Cox DR (1964) An analysis of transformations. J Royal Statist Soc 26(2):211–252. https://doi.org/10.1080/01621459.1981.1047764910.1080/01621459.1981.10477649 ↗
70. Dodge Y (2010) The concise encyclopedia of statistics. Springer, London
71. Suzuki K (1990) Mechanism of steel corrosion in cracked concrete. Corros Reinforce oncrete 1:19–28
72. Michel A, Pease BJ, Geiker MR, Stang H, Olesen JF (2011) Monitoring reinforcement corrosion and corrosion-induced cracking using non-destructive x-ray attenuation measurements. Cement Concrete Res 21:1085–1094. https://doi.org/10.1016/j.cemconres.2011.06.00610.1016/j.cemconres.2011.06.006 ↗
73. Van Steen C, Pahlavan L, Wevers M, Verstrynge E (2019) Localisation and characterisation of corrosion damage in reinforced concrete by means of acoustic emission and X-ray computed tomography. Construct Build Mater 197(2):21–29. https://doi.org/10.1016/j.conbuildmat.2018.11.15910.1016/j.conbuildmat.2018.11.159 ↗