journal article·2020-08Open access

Glulam columns made of European beech timber: compressive strength and stiffness parallel to the grain, buckling resistance and adaptation of the effective-length method according to Eurocode 5

Thomas Ehrhart, René Steiger, Pedro Palma, Ernst Gehri, Andrea Frangi

Materials and Structures· Volume 53· Issue 4

Abstract

Abstract This article presents experimental and numerical investigations on the buckling behaviour of glulam columns made of European beech (Fagus sylvatica L.) timber and a design proposal. First, the compressive strength parallel to the grain ($$\textit{f}_{\mathrm{c,0}}$$) and the modulus of elasticity parallel to the grain ($$\textit{E}_{\mathrm{c,0}}$$) were experimentally determined in tests on stocky columns (slenderness ratio $$\lambda = 12.5$$) of strength classes GL 40h, GL 48h, and GL 55h. Subsequent experimental buckling tests on slender columns with buckling lengths of 2.40 m ($$\lambda = 41.5$$) and 3.60 m ($$\lambda = 62.3$$) allowed investigating the buckling behaviour and quantifying the influence of the buckling length on the buckling resistance. Applicability of the effective-length method, which is the design method for columns in Eurocode 5 (EN 1995-1-1: Design of timber structures - Part 1-1: General - Common rules and rules for buildings. European Committee for Standardization, Brussels, 2010), was evaluated and a proposal for input parameters valid for columns made of European beech glulam is made. Numerical simulations revealed buckling resistances very close to the experimental results, confirming the proposed critical relative slenderness ratio $$\lambda _{\mathrm{rel,0}} = 0.25$$ and the fitted straightness factor $$\beta _{\mathrm{c}} = 0.25$$. In addition, the numerical simulations allowed for an extension of the scope of the investigations.
Source: crossref · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Wood Treatment and Properties · Tree Root and Stability Studies · Natural Fiber Reinforced Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. EN 1995-1-1 (2010) Design of timber structures–part 1-1: general–common rules and rules for buildings. CEN European Committee for Standardization, Brussels
2. EN 1993-1-1 (2010) Design of steel structures—part 1-1: general rules and rules for buildings. CEN European Committee for Standardization, Brussels
3. Blaß HJ (1987) Tragfähigkeit von Druckstäben aus Brettschichtholz unter Berücksichtigung streuender Einflussgrössen. Dissertation, University Fridericiana Karlsruhe, Karlsruhe, Germany
4. Blaß HJ (1987) Design of timber columns, paper 20-2-2. CIB—Meeting Twenty, Dublin, Ireland
5. Theiler M (2014) Stabilität von axial auf Druck beanspruchten Bauteilen aus Vollholz und Brettschichtholz. Dissertation, ETH Zürich, Zurich, Switzerland
6. Estévez Cimadevilla J, Otero Chans D, Martín Gutiérrez E, Vázquez Rodríguez J (2013) Experimental analysis of glued-laminated timber bars with box section used in the construction of a spatial grid. Maderas. Ciencia y tecnología 15(2):153–170
7. Fleming PH, Ramage MH (2020) Full-scale construction and testing of stress-laminated columns made with low-grade wood. Constr Build Mater 230:11695210.1016/j.conbuildmat.2019.116952 ↗
8. Ehrhart T, Steiger R, Palma P, Frangi A (2018) Mechanical properties of European beech (Fagus sylvatica L.) glued laminated timber. Paper 51-12-4. International network on timber engineering research INTER—meeting fifty-one. Tallinn, Estonia, pp 343–360
9. Westermayr M, Stapel P, Van de Kuilen JWG (2018) Tensile and compression strength of small cross-section beech glulam members. Paper 51-12-2. International network on timber engineering research INTER—meeting fifty-one. Tallinn, Estonia, pp 307–322
10. Ehrhart T, Fink G, Steiger R, Frangi A (2015) Strength grading of European beech lamellas for the production of GLT and CLT. Paper 49-5-1. International network on timber engineering research INTER—meeting forty-nine. Graz, Austria, pp 29–43
11. Lehmann M, Clerc G, Lehringer C, Strahm T, Volkmer T (2018) Investigation of the bond quality and the finger joint strength of beech glulam. In: World conference on timber engineering 2018. Seoul, Republic of Korea
12. EN 408 (2012) Timber structures—structural timber and glued laminated timber—determination of some physical and mechanical properties. CEN European Committee for Standardization, Brussels
13. von Tetmajer L (1888) Zur Frage der Knickfestigkeit der Bauhölzer. Schweizerische Bauzeitung 17(11/12):110–113
14. Theiler M, Frangi A, Steiger R (2012) Design of timber columns based on 2nd order structural analysis. Paper 45-2-1. CIB—meeting forty five. Växjö, Sweden, pp 81–96
15. Frangi A, Theiler M, Steiger R (2015) Design of timber members subjected to axial compression or combined axial compression and bending based on 2nd order theory. Paper 48-2-2. CIB—meeting forty eight. Šibenik, Croatia, pp 45–60
16. Glos P (1978) Zur Bestimmung des Festigkeitsverhaltens von Brettschichtholz bei Druckbeanspruchung aus Werkstoff- und Einwirkungsgrössen. Dissertation, TU Munich, Munich, Germany
17. Glos P, Denzler JK, Linsenmann P (2004) Strength and stiffness behaviour of beech laminations for high strength glulam. Paper 37-6-3. CIB—meeting thirty-seven. Edinburgh, Scotland
18. O’Halloran MR (1973) Curvilinear stress–strain relationship for wood in compression. Dissertation, Colorado State University, Fort Collins, US
19. Hartnack R (2004) Langzeitverhalten von druckbeanspruchten Bauteilen aus Holz. Dissertation, Bauhaus-Universität Weimar, Weimar, Germany
20. Ehrhart T (2019) European beech glued laminated timber. Dissertation, ETH Zürich, Zurich, Switzerland
21. Roš M, Brunner J (1931) Die Knickfestigkeit der Bauhölzer. Kongress des internationalen Verbandes für Materialprüfung, Zurich, Switzerland
22. Buchanan A (1984) Strength model and design methods for bending and axial load interaction in timber members. Dissertation, University of British Columbia, Vancouver, Canada
23. Hörsting OP (2008) Zum Tragverhalten druck- und biegebeanspruchter Holzbauteile. Dissertation, TU Braunschweig, Braunschweig, Germany
24. JCSS Probabilistic Model Code (2006) Part 3—resistance models. ISBN 978-3-909386-79-6
25. Ehlbeck J, Blaß HJ (1987) Zuverlässigkeit von Holzdruckstäben. Bauforschung, Report T 1984, Fraunhofer IRB Verlag
26. Ehlbeck J, Blaß HJ (1987) Imperfektionsannahmen für Holzdruckstäbe. Holz als Roh- und Werkstoff 45:231–23510.1007/BF02616414 ↗