journal article·2016-01

Experimental and finite element analysis research on I-beam under web crippling

Yu Chen, Xixiang Chen, Chaoyang Wang

Materials and Structures· Volume 49· Issue 1-2
Publisher page

Abstract

To research web crippling property of I-beam under concentrated load, 48 I-beam with different boundary conditions, loading conditions, bearing lengths and section heights were tested. The experimental scheme, failure modes, concentrated load–general vertical deformation and equivalent strain distribution curves were presented in the paper. The effects of boundary condition, loading condition, bearing length and section height on web crippling ultimate capacity and ductility of I-beam were also studied. Results of these tests show that as bearing length increases, web crippling ultimate capacity of I-beam increase significantly. When bearing length was 50 and 100 mm, web crippling ultimate capacity of I-beam with web slenderness = 17.5 reached its peak; when the bearing length was 150 mm, web crippling ultimate capacity of I-beam with web slenderness = 22.5 reached its peak. The middle web entered plasticity and formed plastic hinge zone in the ultimate limit state. The web crippling ultimate capacity of I-beam with bearing length = 50 mm in interior one flange condition, interior two flanges condition, end one flange and end two flanges condition decreased progressively. Finite element analysis could simulate experimental failure mode and web crippling ultimate capacity. The simple calculation method of web crippling ultimate capacity put forward in the paper can accurately predict experimental value.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Load-Bearing Analysis · Structural Engineering and Vibration Analysis · Structural Behavior of Reinforced Concrete

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Lyse I, Godfrey HJ (1933) Web crippling of steel beams. Fritz Laboratory Reports, p 1148
2. Zhou F, Young B (2008) Aluminum tubular sections subjected to web crippling—Part I: tests and finite element analysis. Thin-Walled Struct 46:339–35110.1016/j.tws.2007.10.003 ↗
3. Zhou F, Young B (2008) Aluminum tubular sections subjected to web crippling—Part II: proposed design equations. Thin-Walled Struct 46:352–36110.1016/j.tws.2007.10.002 ↗
4. Stephens SF, Laboube RA (2003) Web crippling and combined bending and web crippling of cold-formed steel beam headers. Thin-Walled Struct 41:1073–108710.1016/S0263-8231(03)00124-1 ↗
5. Ren WX, Fang SE, Young B (2006) Analysis and design of cold-formed steel channels subjected to combined bending and web crippling. Thin-Walled Struct 44:314–32010.1016/j.tws.2006.03.009 ↗
6. Carden LP, Pekcan G, Itani AM (2007) Web yielding, crippling, and lateral buckling under post loading. J Struct Eng 133:665–67310.1061/(ASCE)0733-9445(2007)133:5(665) ↗
7. Cevik A (2007) A new formulation for web crippling strength of cold-formed steel sheeting using genetic programming. J Constr Steel Res 63:867–88310.1016/j.jcsr.2006.08.012 ↗
8. Okazaki T, Siljenberg BJ, Shield CK et al (2009) Web crippling strength of a steel sandwich panel with V-shaped webs. J Constr Steel Res 65:1721–173010.1016/j.jcsr.2009.03.008 ↗
9. Macdonald M, Heiyantuduw MAD, Kotelko M et al (2011) Web crippling behaviour of thin-walled lipped channel beams. Thin-Walled Struct 49:38–4810.1016/j.tws.2010.09.010 ↗
10. Uzzaman A, Lim JB, Nash D et al (2012) Cold-formed steel sections with web openings subjected to web crippling under two-flange loading conditions—Part I: tests and finite element analysis. Thin-Walled Struct 56:38–4810.1016/j.tws.2012.03.010 ↗
11. Uzzaman A, Lim JB, Nash D et al (2012) Cold-formed steel sections with web openings subjected to web crippling under two-flange loading conditions—Part II: parametric study and proposed design equations. Thin-Walled Struct 56:79–8710.1016/j.tws.2012.03.009 ↗
12. Uzzaman A, Lim JB, Nash D et al (2013) Effect of offset web holes on web crippling strength of cold-formed steel channel sections under end-two-flange loading condition. Thin-Walled Struct 65:34–4810.1016/j.tws.2012.12.003 ↗
13. Bock M, Arrayago I, Real E et al (2013) Study of web crippling in ferritic stainless steel cold formed sections. Thin-Walled Struct 69:29–4410.1016/j.tws.2013.03.015 ↗
14. Natario P, Silvestre N, Camotim D (2014) Web crippling failure using quasi-static FE models. Thin-Walled Struct 84:34–4910.1016/j.tws.2014.05.003 ↗
15. Wu C, Bai Y (2014) Web crippling behaviour of pultruded glass fibre reinforced polymer sections. Compos Struct 108:789–80010.1016/j.compstruct.2013.10.020 ↗
16. Chinese Code (2002) Metallic materials-tensile testing at ambient temperature. GB/T 228-2002. Beijing (in Chinese)
17. Eurocode 3 (EC3, 2005) Design of steel structures—Part 1–3: general rules–supplementary rules for cold-formed members and sheeting, EN 1993-1-8. CEN, Brussels
18. Kurobane Y, Makino Y, Ochi K (1984) Ultimate resistance of unstiffened tubular joints. J Struct Eng ASCE 110(2):385–40010.1061/(ASCE)0733-9445(1984)110:2(385) ↗
19. Wang W, Chen YY, Meng XD, Leon RT (2010) Behavior of thick-walled CHS X-joints under cyclic out-of-plane bending. J Constr Steel Res 66(6):826–83410.1016/j.jcsr.2010.01.014 ↗
20. Chen Y, Feng R, Wang J (2015) Behaviour of bird-beak square hollow section X-joints under in-plane bending. Thin-Walled Struct 86:94–10710.1016/j.tws.2014.10.008 ↗
21. GB50017-2003 Code for design of steel structure (2003). Beijing (in Chinese)
22. ABAQUS (2006) Standard user’s manual. Version 6.11, vols 1–3. Hibbitt, Karlsson and Sorensen, Inc., Pawtucket