journal article·2026Open access

Influence of vat polymerization methods on surface and bonding behavior of additive manufactured dental resins

İrem B. Yeşil Kurt, Nursena Öztemel, Almira A. Diken Türksayar

Journal of Oral Science· Volume 68· Issue 1

Abstract

PURPOSE: To investigate the surface roughness (Ra), shear bond strength (SBS), and Vickers hardness number (VHN) of additive manufactured interim resins manufactured through different vat polymerization techniques. METHODS: Samples were divided into four groups; additive manufacturing technology (Stereolithography:S-FL; Digital light processing:D-AS; Liquid crystal display:L-PH) and subtractive manufacturing technology (Polymethylmethacrylate: MP) (n = 10). After polishing, the Ra values were measured and resin material was then applied. Following thermocycling, SBS tests and VHN tests were carried out. The obtained data were evaluated using one-way analysis of variance (ANOVA) (a = 0.05). RESULTS: Significant differences were observed between the groups for SBS (P = 0.02) and VHN (P < 0.001), whereas the Ra values were not statistically significant (P = 0.148). D-AS and L-PH had higher and similar SBS (P = 1.000) while MP had statistically lower SBS. D-AS demonstrated higher VHN than all groups (P < 0.001) with the exception of S-FL (P = 0.831). MP had lower VHN than all groups (P < 0.01) other than L-PH (P = 0.143). CONCLUSION: All fabrication methods had clinically acceptable SBS values, L-PH and D-AS had higher results. D-AS demonstrated superiority in terms of VHN, all groups exhibited comparable Ra values.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Dental materials and restorations · Anatomy and Medical Technology · Orthodontics and Dentofacial Orthopedics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Prosthodontics, Biruni University, Faculty of Dentistry

Funding

Research Fund of the Biruni University Research and Development Coordination Office Directorate

References (34)

Show source-provided references
1. 1. Kim D, Shim JS, Lee D, Shin SH, Nam NE, Park KH et al. (2020) Effects of post-curing time on the mechanical and color properties of three-dimensional printed crown and bridge materials. Polymers 12, 2762. doi: 10.3390/polym1211276210.3390/polym12112762 ↗
2. 2. Diken Turksayar AA, Donmez MB, Olcay EO, Demirel M, Demir E (2022) Effect of printing orientation on the fracture strength of additively manufactured 3-unit interim fixed dental prostheses after aging. J Dent 124, 104155. doi: 10.1016/j.jdent.2022.10415510.1016/j.jdent.2022.104155 ↗
3. 3. Alammar A, Kois JC, Revilla‐León M, Att W (2022) Additive manufacturing technologies: current status and future perspectives. J Prosthodont 31, 4-12. doi: 10.1111/jopr.1347710.1111/jopr.13477 ↗
4. 4. Piedra-Cascón W, Krishnamurthy VR, Att W, Revilla-León M (2021) 3D printing parameters, supporting structures, slicing, and post-processing procedures of vat-polymerization additive manufacturing technologies: a narrative review. J Dent 109, 103630. doi: 10.1016/j.jdent.2021.10363010.1016/j.jdent.2021.103630 ↗
5. 5. Quan H, Zhang T, Xu H, Luo S, Nie J, Zhu X (2020) Photo-curing 3D printing technique and its challenges. Bioact Mater 5, 110-115. doi: 10.1016/j.bioactmat.2019.12.00310.1016/j.bioactmat.2019.12.003 ↗
6. 6. Schweiger J, Edelhoff D, Güth JF (2021) 3D printing in digital prosthetic dentistry: an overview of recent developments in additive manufacturing. J Clin Med 10, 2010. doi: 10.3390/jcm1009201010.3390/jcm10092010 ↗
7. 7. Lee HE, Alauddin MS, Mohd Ghazali MI, Said Z, Mohamad Zol S (2023) Effect of different vat polymerization techniques on mechanical and biological properties of 3D-printed denture base. Polymers 15, 1463.8. doi: 10.3390/polym1506146310.3390/polym15061463 ↗
8. 8. Ellakany P, Fouda SM, Mahrous AA, AlGhamdi MA, Aly NM (2022) Influence of CAD/CAM milling and 3D-printing fabrication methods on the mechanical properties of 3-unit interim fixed dental prosthesis after thermo-mechanical aging process. Polymers 14, 4103. doi: 10.3390/polym1419410310.3390/polym14194103 ↗
9. 9. Zhang J, Hu Q, Wang S, Tao J, Gou M (2019) Digital light processing based three-dimensional printing for medical applications. Int J Bioprinting 6, 242. doi: 10.18063/ijb.v6i1.24210.18063/ijb.v6i1.242 ↗
10. 10. Mai HN, Lee KB, Lee DH (2017) Fit of interim crowns fabricated using photopolymer-jetting 3D printing. J Prosthet Dent 118, 208-215. doi: 10.1016/j.prosdent.2016.10.03010.1016/j.prosdent.2016.10.030 ↗
11. 11. Abdullah AO, Pollington S, Liu Y (2018) Comparison between direct chairside and digitally fabricated temporary crowns. Dent Mater J 37, 957-963. doi: 10.4012/dmj.2017-31510.4012/dmj.2017-315 ↗
12. 12. Alageel O, Alhijji S, Alsadon O, Alsarani M, Gomawi AA, Alhotan A (2023) Trueness, flexural strength, and surface properties of various three-dimensional (3D) printed interim restorative materials after accelerated aging. Polymers 15, 3040. doi: 10.3390/polym1514304010.3390/polym15143040 ↗
13. 13. de Souza FA, Blois MC, Collares K, Dos Santos MBF (2024) 3D-printed and conventional provisional single crown fabrication on anterior implants: a randomized clinical trial. Dent Mater 40, 340-347. doi: 10.1016/j.dental.2023.12.00410.1016/j.dental.2023.12.004 ↗
14. 14. Pituru SM, Greabu M, Totan A, Imre M, Pantea M, Spinu T et al. (2020) A review on the biocompatibility of PMMA-based dental materials for interim prosthetic restorations with a glimpse into their modern manufacturing techniques. Materials 13, 2894. doi: 10.3390/ma1313289410.3390/ma13132894 ↗
15. 15. Sampaio CS, Niemann KD, Schweitzer DD, Hirata R, Atria PJ (2021) Microcomputed tomography evaluation of cement film thickness of veneers and crowns made with conventional and 3D printed provisional materials. J Esthet Restor Dent 33, 487-495. doi: 10.1111/jerd.1265110.1111/jerd.12651 ↗
16. 16. Lankes V, Reymus M, Liebermann A, Stawarczyk B (2023) Bond strength between temporary 3D printable resin and conventional resin composite: influence of cleaning methods and air-abrasion parameters. Clin Oral Investig 27, 31-43. doi: 10.1007/s00784-022-04800-710.1007/s00784-022-04800-7 ↗
17. 17. Dewan H, Sayed ME, Jundus A, Gharawi M, Baeshen S, Alali M et al. (2023) Shear strength of repaired 3D-printed and milled provisional materials using different resin materials with and without chemical and mechanical surface treatment. Polymers 15, 4284. doi: 10.3390/polym1521428410.3390/polym15214284 ↗
18. 18. Lad PP, Kamath M, Tarale K, Kusugal PB (2014) Practical clinical considerations of luting cements: a review. J Int Oral Health 6, 116-120.
19. 19. Albahri R, Yoon HI, Lee JD, Yoon S, Lee SJ (2021) Shear bond strength of provisional repair materials bonded to 3D printed resin. J Dent Sci 16, 261-267. doi: 10.1016/j.jds.2020.05.00310.1016/j.jds.2020.05.003 ↗
20. 20. Holmer L, Othman A, Lührs AK, von See C (2019) Comparison of the shear bond strength of 3D printed temporary bridges materials, on different types of resin cements and surface treatment. J Clin Exp Dent 11, e367-e372. doi: 10.4317/jced.5561710.4317/jced.55617 ↗
21. 21. Su N, Yue L, Liao Y, Liu W, Zhang H, Li X et al. (2015) The effect of various sandblasting conditions on surface changes of dental zirconia and shear bond strength between zirconia core and indirect composite resin. J Adv Prosthodont 7, 214-223. doi: 10.4047/jap.2015.7.3.21410.4047/jap.2015.7.3.214 ↗
22. 22. Zhou L, Qian Y, Zhu Y, Liu H, Gan K, Guo J (2014) The effect of different surface treatments on the bond strength of PEEK composite materials. Dent Mater 30, e209-e215 doi: 10.1016/j.dental.2014.03.01110.1016/j.dental.2014.03.011 ↗
23. 23. Alp G, Johnston WM, Yilmaz B (2019) Optical properties and surface roughness of prepolymerized poly (methyl methacrylate) denture base materials. J Prosthet Dent 121, 347-352. doi: 10.1016/j.prosdent.2018.03.00110.1016/j.prosdent.2018.03.001 ↗
24. 24. de Castro EF, Nima G, Rueggeberg FA, Araújo-Neto VG, Faraoni JJ, Palma-Dibb et al. (2023) Effect of build orientation in gloss, roughness and color of 3D-printed resins for provisional indirect restorations. Dent Mater 39, e1-e11. doi: 10.1016/j.dental.2023.05.00210.1016/j.dental.2023.05.002 ↗
25. 25. Wadhwani V, Sivaswamy V, Rajaraman V (2022) Surface roughness and marginal adaptation of stereolithography versus digital light processing threedimensional printed resins: An: in-vitro: study. J Indian Prosthodont Soc 22, 377-381. doi: 10.4103/jips.jips_8_2210.4103/jips.jips_8_22 ↗
26. 26. International Organization for Standardization (2020) Dentistry--Polymer-based crown and bridge materials. ISO 10477:2020, Geneve.
27. 27. Ersöz B, Aydın N, Ezmek B, Karaoglanoğlu S, Çal IK (2024) Effect of surface treatments applied to 3D printed permanent resins on shear bond strength. J Clin Exp Dent 16, e1059-e1066. doi: 10.4317/jced.6188410.4317/jced.61884 ↗
28. 28. Khanlar LN, Revilla-León M, Barmak AB, Ikeda M, Alsandi Q, Tagami J et al. (2023) Surface roughness and shear bond strength to composite resin of additively manufactured interim restorative material with different printing orientations. J Prosthet Dent 129, 788-795. doi: 10.1016/j.prosdent.2021.08.01010.1016/j.prosdent.2021.08.010 ↗
29. 29. Reymus M, Lümkemann N, Stawarczyk B (2019) 3D-printed material for temporaryrestorations: impact of print layer thickness and post-curing method on degree of conversion. Int J Comput Dent 22, 231-237. doi: 10.1007/s00784-019-02952-710.1007/s00784-019-02952-7 ↗
30. 30. Al-Qahtani AS, Tulbah HI, Binhasan M, Abbasi MS, Ahmed N, Shabib S et al. (2021) Surface properties of polymer resins fabricated with subtractive and additive manufacturing techniques. Polymers 13, 4077. doi: 10.3390/polym1323407710.3390/polym13234077 ↗
31. 31. Alshamrani AA, Raju R, Ellakwa A (2022). Effect of printing layer thickness and postprinting conditions on the flexural strength and hardness of a 3D-printed resin. Biomed Res Int 2022, 8353137. doi:10.1155/2022/835313710.1155/2022/8353137 ↗
32. 32. Katheng A, Prawatvatchara W, Chaiamornsup P, Sornsuwan T, Lekatana H, Palasuk J (2025) Comparison of mechanical properties of different 3D printing technologies. Sci Rep 15, 18998. doi: 10.1038/s41598-025-03632-110.1038/s41598-025-03632-1 ↗
33. 33. Tsolakis IA, Papaioannou W, Papadopoulou E, Dalampira M, Tsolakis AI (2022) Comparison in terms of accuracy between DLP and LCD printing technology for dental model printing. Dent J 10, 181. doi: 10.3390/dj1010018110.3390/dj10100181 ↗
34. 34. Sağlam G, Cengiz S, Köroğlu A, Şahin O, Velioğlu N (2023). Comparison of the micro-shear bond strength of resin cements to CAD/CAM glass ceramics with various surface treatments. Materials (Basel) 16, 2635. doi: 10.3390/ma1607263510.3390/ma16072635 ↗