Influence of calendering on the properties of paper-derived alumina ceramics
Source abstract
Abstract
Abstract The effect of calendering of alumina loaded preceramic papers in a hard nip laboratory calender at various temperatures, line loads and times of nip passes on their green and sintered properties was investigated. The main objective was to achieve a maximum densification, which resulted in a maximum reduction of thickness of 45%, a green density of 80.5% of the theoretical density and a sintered density of 81% of the theoretical density. The ring-on-ring flexural strength of sintered specimen could be increased from 71±11 MPa to 138±33 MPa. The surface roughness of green samples could be diminished to a value for Ra of below 2 µm compared to an Ra of 13.2 µm for an uncalendered paper, whereas the Ra value of the sintered samples was much higher due to the burn-off of the cellulose fibers. Preceramic papers manufactured by the dynamic hand-sheet-forming process exhibit a fiber-orientation which causes anisotropic effects regarding the sintering shrinkage, the surface roughness and Young's modulus.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Material Properties and Processing · Advanced Cellulose Research Studies · Textile materials and evaluations
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Preceramic paper-derived ceramics10.1111/j.1551-2916.2008.02752.x ↗
2. Glättung von Papier und Karton – Heutiger Stand der Technik
3. A. Todorović, T. Hämäläinen, Proceedings of the Shoe Nip Calender Possibilities for Board and Paper, Tappi Spring Technical Conference, 2003.
4. Finishing alternative for offset LWC
5. Moisture-dependent thermal softening of paper, evaluated by its elastic modulus
6. The glass transition of wood from the viewpoint of mechanical pulping10.1007/BF00350984 ↗
7. Paper complexity and the interpretation of conservation research10.2307/3179657 ↗
8. The moisture and rate-dependent mechanical properties of paper: a review10.1023/A:1009833415827 ↗
9. The glass transition and crystallization of ball-milled cellulose10.1007/s10570-010-9425-7 ↗
10. Fundamental aspects of adhesion between cellulose surfaces in contact – a review
11. Viscoelastic modeling of paper in a calender nip
12. Description and analysis of paper deformation in a calendar nip – effects of high roll temperatures and thickness variations10.3183/NPPRJ-2002-17-02-p130-138 ↗
13. Compression behavior of pulp fiber networks10.1002/pen.20004 ↗
14. Softcalendering: effect of temperature, pressure and speed on sheet properties10.3183/NPPRJ-1997-12-01-p013-018 ↗
15. Kerekes · Pulp Pap. Can. · 1974 · 75 · T359
16. Influence of the calendering conditions on the structure and the properties of woodfree paper – a comparison between soft nip and hard nip calendering10.3183/NPPRJ-1998-13-01-p068-075 ↗
17. Microstructure and properties of paper-derived porous Al2O3 substrates
18. Paper-derived stoneware ceramics: improvement of properties by calendaring and evaluation of pyroplastic deformation behavior
19. Lindblad · 2001
20. S. Loewen, M. Foulger, Tensile Stiffness Properties: TSI, TSO and Fibre Orientation: an Introduction, 2002. 〈http://www.pulpandpapercanada.com/news/tensile-stiffness-properties-tso-and-fibre-orientation-an-introduction/1000185068/〉 (accessed 05.28.13).
21. Influence of porosity on Young's modulus and Poisson's ratio in alumina ceramics10.1016/S0955-2219(00)00314-9 ↗
22. R.J. Kerekes, Heat transfer in calendering, in: Proceedings of the Technical Section of the Canadian Pulp and Paper Association, vol. 3 (5) 1979, pp. 66–73.
23. Alumina–alumide alloys (3a) technology: I, model development10.1111/j.1151-2916.2000.tb01437.x ↗
24. Regression analysis of temperature-dependent mechanical and thermal properties of dielectric technical ceramics10.1007/s10853-012-6759-6 ↗
25. Heat capacity measurements of various biomass types and pyrolysis residues10.1016/j.fuel.2013.07.086 ↗
26. Effect of porosity on physical properties of sintered alumina10.1111/j.1151-2916.1956.tb15608.x ↗
27. 3D modelling of random, cellulosic fibrous networks based on X-ray tomography and image analysis10.1016/j.compscitech.2004.12.038 ↗
28. Influence of pore geometry on the effective response of porous media10.1023/A:1004528600213 ↗
29. Derivation of the exponential relation for the effect of ellipsoidal porosity on elastic modulus10.1111/j.1151-2916.1996.tb08955.x ↗
30. Preparation and properties of porous alumina ceramics with oriented cylindrical pores produced by an extrusion method10.1016/j.jeurceramsoc.2004.11.015 ↗