Influence of material parameters on the interfacial crack growth in thermal barrier coating system
Source abstract
Abstract
Abstract Surface crack failure and interfacial crack failure are typical failure modes in thermal barrier coating (TBC) system. The most common failure form is the peeling of top coat (TC) caused by interfacial crack. In this study, the influence of material parameter on the energy release rate of interfacial crack in TBC system was studied by extended finite element method. The influence of the elastic modulus of TC and the elastic modulus of bond coat (BC) was considered, and the effect of the crack position and length was also taken into account. The results show that the value of the energy release rate at TC/thermally grown oxide (TGO) and TGO/BC interfaces increases with the increase of the elastic modulus of TC, and the increase rate increases with the increase of crack length. With the increase of crack length, the value of the energy release rate and the increase rate increase. With the increase of the elastic modulus of BC, the influence of the shorter cracks at TC/TGO interface decreases, while for the longer cracks, the value of the energy release rate decreases with the increase of the elastic modulus of BC, and the decrease rate of the energy release rate decreases with the elastic modulus of BC increasing. For TGO/BC interface crack, the value of the energy release rate gradually decreases with the increase of the elastic modulus of BC, and the longer the crack length is, the more obvious the influence is. Both the elastic moduli of TC and BC have more influence on TC/TGO interfacial cracks than on TGO/BC interfacial cracks.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Thermal barrier coatings for gas-turbine engine applications10.1126/science.1068609 ↗
2. Mechanisms controlling the durability of thermal barrier coatings10.1016/S0079-6425(00)00020-7 ↗
3. Review of suspension and solution precursor plasma sprayed thermal barrier coatings10.1016/j.ceramint.2016.06.063 ↗
4. Calcia-magnesia-alumino-silicate (CMAS)-induced degradation and failure of air plasma sprayed yttria-stabilized zirconia thermal barrier coatings10.1016/j.actamat.2015.12.044 ↗
5. Numerical study on interaction of surface cracking and interfacial delamination in thermal barrier coatings under tension10.1016/j.apsusc.2014.07.142 ↗
6. Residual stress redistribution within high-temperature coatings due to surface cracks10.1016/j.matdes.2006.07.007 ↗
7. The surface cracking behavior in air plasma sprayed thermal barrier coating system incorporating interface roughness effect10.1016/j.apsusc.2011.08.103 ↗
8. The effect of thermally grown oxide on multiple surface cracking in air plasma sprayed thermal barrier coating system10.1016/j.surfcoat.2012.06.074 ↗
9. Multiple surface thermal fracture of graded ceramic coatings10.1080/01495739808956171 ↗
10. Investigation on periodic cracking of elastic film/substrate system by the extended finite element method10.1016/j.apsusc.2011.02.111 ↗
11. Surface thermal cracking of thermal barrier coatings owing to stress relaxation: zirconia vs. mullite10.1016/0257-8972(95)02647-9 ↗
12. Effects of geometrical and material parameters of top and bond coats on the interfacial fracture in thermal barrier coating system10.1016/j.matdes.2012.12.053 ↗
13. Performance of TBCs system due to the different thicknesses of top ceramic layer10.1016/j.ceramint.2014.10.105 ↗
14. Competition mechanism of interfacial cracks in thermal barrier coating system
15. Influences of interface morphology and thermally grown oxide thickness on residual stress distribution in thermal barrier coating system10.1016/j.ceramint.2016.02.049 ↗
16. Effect of material properties on residual stress distribution in thermal barrier coatings10.1016/j.ceramint.2017.11.127 ↗
17. Determination of interface fracture toughness in thermal barrier coating system by blister tests10.1115/1.1555658 ↗
18. Influence of the stress state on void nucleation and subsequent growth around inclusion in ductile material10.1007/s10704-015-0016-3 ↗
19. Three-dimensional thermal weight function method for the interface crack problems in bimaterial structures under a transient thermal loading10.1080/01495739.2016.1152108 ↗
20. Delamination cracking in thermal barrier coating system
21. Thermal fatigue failure induced by delamination in thermal barrier coating10.1016/S0142-1123(01)00096-2 ↗
22. Effect of surface pre-crack morphology on the fracture of thermal barrier coatings under thermal shock10.1016/j.actamat.2004.05.035 ↗
23. Numerical analysis of CMAS penetration induced interfacial delamination of transversely isotropic ceramic coat in thermal barrier coating system10.1016/j.surfcoat.2015.08.054 ↗
24. Interfacial delamination of double-ceramic-layer thermal barrier coating system10.1016/j.ceramint.2014.05.095 ↗
25. Effect of pre-existing surface crack morphology on the interfacial thermal fracture of thermal barrier coatings: a numerical study10.1016/S0921-5093(02)00730-X ↗
26. Effect of periodic surface cracks on the interfacial fracture of thermal barrier coating system10.1016/j.apsusc.2012.06.036 ↗
27. Multiple surface cracking and its effect on interface cracks in functionally graded thermal barrier coatings under thermal shock10.1115/1.1533809 ↗
28. The effect of periodic segmentation cracks on the interfacial debonding: study on interfacial stresses10.1016/j.surfcoat.2005.11.115 ↗
29. Interfacial toughness evaluation of thermal barrier coatings by bending test10.1016/j.taml.2017.09.007 ↗
30. Bending-driven failure mechanism and modelling of double-ceramic-layer thermal barrier coating system
31. Acoustic emission evaluation of the fracture behavior of APS-TBCs subjecting to bondcoating oxidation10.1002/sia.2586 ↗
32. Mechanisms governing the failure modes of dense vertically cracked thermal barrier coatings10.1016/j.engfracmech.2017.11.037 ↗
33. Crack propagation modeling on the interfaces of thermal barrier coating system with different thickness of the oxide layer and different interface morphologies10.1016/j.matdes.2011.05.039 ↗
34. Development of a micromechanical life prediction model for plasma sprayed thermal barrier coatings10.1016/S0921-5093(00)01853-0 ↗
35. Predicting failure within TBC system: finite element simulation of stress within TBC system as affected by sintering of APS TBC, geometry of substrate and creep of TGO
36. Interface stress evolution considering the combined creep–plastic behavior in thermal barrier coatings10.1016/j.matdes.2015.09.146 ↗
37. Finite element simulation on thermal fatigue of a turbine blade with thermal barrier coatings10.1016/j.jmst.2013.11.005 ↗
38. 2011
39. Improvement of the extended finite element method for ductile crack growth10.1016/j.msea.2012.05.014 ↗
40. XFEM for direct evaluation of mixed mode SIFs in homogeneous and bi-materials10.1002/nme.906 ↗