Microstructure and properties of in-situ composite coatings prepared by plasma spraying MoO3–Al composite powders
Source abstract
Abstract
Abstract MoO3–Al composite powders were used for preparing in situ composite coatings. Effects of the composition of MoO3–Al composite powder on the microstructure and properties of the as-prepared coatings were investigated. The results show that the main phases of the as-prepared coatings were γ-Al2O3 and Mo. An optimal composition (63 wt%) of MoO3 in MoO3–Al composite powder was demonstrated. The porosity of the as-prepared composite coatings decreased first and then increased with the increase of MoO3. This is attributed to the fact that the melting state of the powder during plasma spraying is closely involved in the content of MoO3. The coating prepared by composite powder with 63 wt% MoO3 had the most Al2O3 and the highest microhardness. The wear resistance of 63 wt% MoO3 composite coating was the best among four coatings with different content of MoO3, which is attributed to its high hardness and good toughness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal and Thin Film Mechanics · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Plasma sprayed Mo-Mo oxide nanocomposites: synthesis and characterization10.1016/S0257-8972(01)01234-8 ↗
2. An evaluation of surface properties and frictional forces generated from Al–Mo–Ni coating on piston ring10.1016/j.apsusc.2004.02.053 ↗
3. Characterization and residual stress analysis of wear resistant Mo thermal spray-coated steel gear wheels10.1016/j.surfcoat.2005.01.103 ↗
4. Effect of the microstructure of thermally sprayed coatings on friction and wear response under lubricated and dry sliding conditions10.1016/j.wear.2006.03.042 ↗
5. Wear behaviour of wear-resistant adaptive nano-multilayered Ti-Al-Mo-N coatings10.1016/j.apsusc.2016.06.102 ↗
6. Microstructure and mechanical properties of Mo coating deposited by supersonic plasma spraying10.1016/j.ijrmhm.2019.105095 ↗
7. Fabrication of nanostructured Mo coatings on Al and Ti substrates by ball impact cladding10.1016/j.surfcoat.2010.09.014 ↗
8. Increasing the stamping tools lifespan by using Mo and B4C PVD coatings10.1016/j.surfcoat.2017.06.043 ↗
9. Tribological properties of molybdenum coatings sprayed by electro-thermal explosion directional spraying10.1016/j.surfcoat.2006.09.028 ↗
10. Investigations on the abrasive wear behaviour of molybdenum coating on SS304 and A36 using HVOF technique
11. Dry sliding wear behaviour of plasma sprayed Al2O3-30%Mo and Mo coating10.1016/j.mspro.2014.07.264 ↗
12. Thermal behaviour of plasma-sprayed Mo coating on cast-iron substrate10.1016/S0257-8972(03)00537-1 ↗
13. Correlation of microstructure and wear resistance of molybdenum blend coatings fabricated by atmospheric plasma spraying10.1016/j.msea.2003.09.062 ↗
14. The effect of Mo content in plasma-sprayed Mo-NiCrBSi coating on the tribological behavior10.1016/j.surfcoat.2010.07.017 ↗
15. Tribological behaviour of plasma sprayed diamond reinforced molybdenum coatings10.1016/j.ijrmhm.2018.10.015 ↗
16. Microstructure and wear resistance of plasma-sprayed molybdenum coating reinforced by MoSi2 particles10.1007/s11666-016-0440-6 ↗
17. Friction and wear properties of WC-Co and Mo-Mo2C based functionally graded materials10.1016/S0043-1648(01)00839-0 ↗
18. Spray-drying of ceramics for plasma-spray coating10.1016/S0955-2219(00)00112-6 ↗
19. Quantitative interpretation of X-ray diffraction patterns of mixtures. III. Simultaneous determination of a set of reference intensities10.1107/S0021889875009454 ↗
20. Method of regularized multipeak reference intensity ratio for quantitative X-ray phase Analysis of polycrystalline materials10.1134/S0020168511150180 ↗
21. Effects of oxide precursors on fabrication of Mo5Si3-Al2O3 composites via thermite-based combustion synthesis10.1016/j.intermet.2016.12.012 ↗
22. Microstructure and properties of in-situ TiB2 matrix composite coatings prepared by plasma spraying10.1016/j.apsusc.2017.04.107 ↗
23. In situ (Al,Cr)2O3-Cr composite coating fabricated by reactive plasma spraying10.1016/j.ceramint.2017.02.042 ↗
24. Microstructure evolution and mechanical properties of in-situ bimodal TiC-Fe coatings prepared by reactive plasma spraying10.1016/j.ceramint.2018.12.051 ↗
25. Reactivity of Al2(MoO4)3 with V2O5 in the solid10.1016/S0167-2738(97)00304-4 ↗
26. Reaction path of the synthesis of α-Al2O3-TiC-TiB2 in an Al-TiO2-B4C system10.1016/j.ijrmhm.2011.04.001 ↗
27. Reactive plasma spraying synthesis and characterization of TiB2-TiC-Al2O3/Al composite coatings on a magnesium alloy10.1016/j.jallcom.2014.01.178 ↗
28. Microstructure and properties of composite coatings prepared by plasma spraying ZrO2-B2O3-Al composite powders10.1016/j.jallcom.2017.12.335 ↗
29. Formation of metastable phases in flame and plasma prepared alumina10.1007/BF02397914 ↗
30. Wear mechanisms in thermally-sprayed Mo based coatings10.1080/10402009408983340 ↗
31. Time-dependent friction response of plasma-sprayed molybdenum10.1016/S0043-1648(98)00395-0 ↗
32. Synthesis of Al2(MoO4)3 by two distinct processes, hydrothermal reaction and solid-state reaction10.1016/j.proeng.2016.06.507 ↗
33. Phase transition and negative thermal expansion in A2(MoO4)3 system(A=Fe3+, Cr3+ and Al3+)10.1016/S0925-8388(01)02003-5 ↗
34. The effect of microstructure on thermal expansion coefficients in powder-processed Al2Mo3O1210.1007/s10853-012-7076-9 ↗
35. Correlation of splat morphologies with porosity and residual stress in plasma-sprayed YSZ coatings10.1016/j.surfcoat.2016.12.061 ↗
36. Study on influence of porosity, pore size, spatial and topological distribution of pores on microhardness of as plasma sprayed ceramic coatings10.1016/j.msea.2006.09.042 ↗
37. Porosity and effective mechanical properties of plasma-sprayed Ni-based alloy coatings10.1016/j.apsusc.2008.10.120 ↗
38. Measurement of residual stress in plasma-sprayed metallic, ceramic and composite coatings10.1016/S0921-5093(98)00860-0 ↗
39. Estimation of residual stress and its effects on the mechanical properties of detonation gun sprayed WC–Co coatings10.1016/j.msea.2009.10.009 ↗
40. The effect on residual stresses of porosity in plasma sprayed MgO–ZrO2 coatings for an internal combustion diesel engine10.1016/j.msea.2003.12.019 ↗
41. Harper · 2001
42. Investigations on the effect of molybdenum (Mo) and molybdenum silicon carbide (Mo-10%SiC) composite coatings on mild steel substrate using HVOF technique
43. Plasma sprayed diamond reinforced molybdenum coatings10.1016/j.jallcom.2018.07.088 ↗
44. Effects of standoff distance on porosity, phase distribution and mechanical properties of plasma sprayed Nd–Fe–B coatings10.1016/j.surfcoat.2012.11.040 ↗
45. Influence of random pore defects on failure mode and mechanical properties of SiC ceramics under uniaxial compression using discrete element method10.1016/j.ceramint.2018.08.349 ↗
46. Influence of ceramic thickness on residual stress and bonding strength for plasma sprayed duplex thermal barrier coating on aluminum alloy10.1016/j.surfcoat.2012.04.070 ↗