Effect of preparation route on the properties of slip-casted Al2O3/YAG composites
Source abstract
Abstract
Alumina composites containing 5, 10 and 20 vol.% YAG were produced by a slip-casting process. Two different routes for adding the YAG phase were chosen. Either by mixing of alumina with previously produced YAG powder or by coating of an adequate amount of yttria to form YAG precipitates during the calcining step. The mechanical properties of the sintered samples were measured and compared. Independent from the preparation route Al2O3/10 vol.% YAG composites showed best mechanical properties. Significant differences in the densification behavior appeared between the two different manufacturing technologies. The presence of intermediately formed phases like YAM and YAP during the powder preparation step of coated composites is probably the reason why mixed composites showed higher mechanical properties than coated composites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Silicone and Siloxane Chemistry · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. Application of eutectic composites to gas turbine system and fundamental fracture properties up to 1700°C10.1016/j.jeurceramsoc.2005.01.003 ↗
2. Engineering property limitations of structural ceramic composites above 1600°C10.1002/9780470313848.ch9 ↗
3. Creep behaviour of alumina/YAG nanocomposites obtained by colloidal processing route10.1016/j.jeurceramsoc.2006.04.177 ↗
4. Processing microstructure mechanical properties of 25vol.% YAG–Al2O3 nanocomposites10.1016/S0965-9773(99)00396-7 ↗
5. High temperature properties of unidirectionally solidified Al2O3/YAG composites10.2320/jinstmet1952.59.1_71 ↗
6. Excellent high-temperature properties of YAG Matrix composites reinforced with sapphire phases
7. Sapphire matrix composites reinforced with single crystal YAG phases10.1007/BF00366367 ↗
8. High-temperature deformation in unidirectionally solidified eutectic Al2O3–YAG single crystal10.4028/www.scientific.net/KEM.171-174.855 ↗
9. Deformation and fracture behavior of Al2O3/YAG composite from room temperature to 2023K10.1016/S0266-3538(01)00159-2 ↗
10. Processing mechanical properties of Al2O3/Y3Al5O12 (YAG) eutectic composites10.1002/9780470313053.ch36 ↗
11. Ultra-high temperature compressive creep behavior of an in-situ Al2O3 single crystal/YAG eutectic composite10.1016/S0955-2219(03)00640-X ↗
12. High temperature plastic behavior of Al2O3–Y3Al5O12 directionally solidified eutictics10.1016/j.actamat.2006.03.002 ↗
13. Tjong · Mater. Sci. Eng. Rep. · 2004 · 45 · 110.1016/j.mser.2004.07.001 ↗
14. Comparative studies of SrZrXMnXFe12−2XO12 nanocomposites synthesis by co-precipitation and sol–gel combustion methods10.1016/j.scriptamat.2006.09.005 ↗
15. Low temperature processing of dense nanocrystalline yttrium-doped cerium oxide ceramics10.1016/S1359-6454(01)00448-7 ↗
16. Comparison among different sintering routes for preparing alumina–YAG nanocomposites10.1016/j.jeurceramsoc.2004.12.020 ↗
17. Synthesis of an alumina–YAG nanopowder via sol–gel method10.1016/j.jallcom.2007.02.044 ↗
18. Effect of milling and calcination temperature of the compressibility and sinterability of nanocrystalline Al2O3–Y3Al5O12 composite powder10.1111/j.1551-2916.2008.02727.x ↗
19. Sol–gel synthesis of YAG/Al2O3 long fibres from water solvent systems10.1016/S0955-2219(99)00254-X ↗
20. Ceramic matrix composites in the alumina/5–30vol.% YAG system10.1016/j.jeurceramsoc.2011.04.003 ↗
21. F. Sommer, F. Kern, R. Gadow, Hot-pressing of yttria–chromia alumina composites, Proc. CIEC, 12, Mons Belgium, S2 (2010).
22. Injection molding of alumina–chromia–yttria composites
23. High-temperature creep of some crystal oxides10.1002/9780470313848.ch10 ↗
24. Optical properties of high-performance polycrystalline Nd:YAG ceramics for solid-state lasers10.1111/j.1151-2916.1995.tb08433.x ↗
25. YAG ceramic processed by slip casting via aqueous slurries10.1016/j.ceramint.2006.10.018 ↗
26. Aqueous slip casting of transparent yttrium aluminum garnet (YAG) ceramics10.1016/j.ceramint.2007.03.010 ↗
27. Effect of dispersant on the rheological properties and slip casting of concentrated alumina slurry10.1111/j.1151-2916.1989.tb06293.x ↗
28. Colloidal processing of ceramics10.1111/j.1151-2916.2000.tb01560.x ↗
29. Aqueous sol–gel synthesis route for the preparation of YAG: evaluation of sol–gel process by mathematical regression model10.1007/s10971-006-9002-6 ↗
30. Alumina-based nanocomposites obtained by doping with inorganic salt solutions: application to immiscible and reactive systems10.1016/j.jeurceramsoc.2008.05.047 ↗
31. Abnormal grain growth in alumina: synergistic effects of yttria and silica10.1111/j.1151-2916.2003.tb03354.x ↗