journal article·2006-01Open access

The effect of fired scrap addition on the sintering behaviour of hard porcelain

Alexander Karamanov, Emilia Karamanova, Anna Maria Ferrari, Fabiola Ferrante, Mario Pelino

Ceramics International· Volume 32· Issue 7

Abstract

Abstract The effect of the addition of porcelain fired scraps on the sintering, phase composition and properties of a hard porcelain was studied. Two ceramics were compared: a commercial triaxial porcelain labelled C-0 and one, where 15% of the mass of C-0 was substituted by scraps yielding a composition labelled C-15. The sintering was evaluated by the linear shrinkage, the water absorption and the variation of closed and total porosity, while the phase transformations were investigated by DTA-TG, dilatometry and XRD. Samples, sintered at 1350 and 1400 °C, were used for the evaluation of the Young modulus and the bending strength. The addition of the fired scrap had a positive effect on the quartz dissolution and on the formation of the liquid phase during the sintering. The sintering and the mechanical properties were improved by heat treatment in the 1300–1350 °C range. Above this temperature, a significant over-firing with a decrease of the mechanical properties was observed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Recycling and utilization of industrial and municipal waste in materials production · Glass properties and applications · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Kingery · 1976
2. Reed · 1995
3. Hlavac · 1983
4. Gerasimov · 1977
5. Porcelain—raw materials, processing, phase evolution, and mechanical behavior10.1111/j.1151-2916.1998.tb02290.x ↗
6. Porcelainized stoneware tile
7. Microstructural evolution in triaxial porcelain10.1111/j.1151-2916.2000.tb01692.x ↗
8. Fired porcelain microstructures revisited10.1111/j.1151-2916.1999.tb02282.x ↗
9. Enhancing the mechanical properties of porcelain stonewere tiles: a microsrtuctural approach10.1016/S0955-2219(00)00266-1 ↗
10. Bending strength of porcelains10.1016/S0272-8842(01)00068-2 ↗
11. Porcelain tile composition effect on phase formation and end products
12. Effect of firing conditions, filler grain size and quartz content on bending strength and physical properties of sanitaryware porcelain10.1016/j.jeurceramsoc.2003.07.003 ↗
13. Influence of zeolites on the sintering and technological properties of porcelain stoneware tiles10.1016/S0955-2219(03)00086-4 ↗
14. Preparation of porcelain tiles from Egyptian raw materials10.1016/S0272-8842(01)00095-5 ↗
15. Use of soda-lime scrap-glass as a fluxing agent in a porcelain stoneware tile mix10.1016/S0955-2219(03)00121-3 ↗
16. Traditional and glass powder porcelain: technical and microstructure analysis10.1016/j.jeurceramsoc.2003.08.003 ↗
17. Effect of soda-lime glass on sintering and technological properties of porcelain stoneware tiles10.1016/S0272-8842(02)00067-6 ↗
18. Incorporation of granite cutting sludge in industrial porcelain tile formulations10.1016/j.jeurceramsoc.2003.10.039 ↗
19. Effect of substitution of fly ash for quartz in triaxial kaolin–quartz–feldspar system10.1016/j.jeurceramsoc.2003.10.008 ↗
20. Utilisation of municipal incinerator grate slag for manufacturing of porcelainized stoneware tiles manufacturing10.1016/S0955-2219(01)00460-5 ↗
21. Feedstock formulations for direct consolidation of porcelains with polysaccharides10.1111/j.1151-2916.2001.tb00732.x ↗
22. Rheological study of waste porcelain feedstocks for injection moulding10.1016/S0955-2219(01)00210-2 ↗
23. Quantitative X-ray diffraction Rietveld analysis of low temperature coal ashes10.4028/www.scientific.net/MSF.79-82.745 ↗
24. Quantitative determination of chrysotile asbestos in bulk materials by combined Rietveld and RIR methods10.1017/S0885715600014962 ↗
25. Larson · 1998
26. Deer · 1992
27. Appen · 1974
28. Microsrtructure, internal stresses and fracture mechanics properties of quartzose silicate materials for whitewares
29. Recent advanced in dilatometry
30. Using the optical dilatometer