High velocity oxygen fuel sprayed Cr3C2-NiCr coatings against Na2SO4 hot corrosion at different temperatures
Source abstract
Abstract
Abstract Cr3C2-NiCr/NiCrAlY coating was prepared by high velocity oxygen fuel (HVOF) spraying. The microstructure and the Na2SO4 hot corrosion behavior at different temperatures of the coating were investigated. The Na2SO4 hot corrosion mechanism of Cr3C2-NiCr coating was also discussed. The results showed that HVOF Cr3C2-NiCr coating was relatively dense and mainly composed of Cr3C2, NiCr and a small amount of Cr7C3 three phases. The dense Cr2O3 layer was formed on the surface of Cr3C2-NiCr coating after Na2SO4 corrosion at 750 °C to further prevent corrosion. The coating had produced the obvious longitudinal crack with the increase of hot corrosion temperature up to 900 °C. The corrosion mechanism of Cr3C2-NiCr coating against the Na2SO4 salt at high-temperature was as follows: firstly, the protective oxidizing film was formed at 750 °C, then the protective oxide film dissolved at the interface between the coating and Na2SO4 salt with the hot corrosion temperature increasing up to 900 °C, and subsequently the dissolved anions and cations could migrate to the interface between molten salt and air and the loose and unprotected oxides were regenerated, thereby exacerbating the failure of the coating.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Nuclear Materials and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Microstructural characteristics and protection performances of plasma sprayed Al2O3-Al composite coatings on AZ91D magnesium alloy
2. Thermally sprayed titanium suboxide coatings for piston ring/cylinder liners under mixed lubrication and dry-running conditions10.1016/j.wear.2006.11.012 ↗
3. The tribological and electrochemical behavior of HVOF sprayed Cr3C2-NiCr ceramic coating on carbon steel10.1016/j.ceramint.2014.12.102 ↗
4. Role of heat treatments in the improvement of the sliding wear properties of Cr3C2–NiCr coatings10.1016/S0257-8972(02)00148-2 ↗
5. Degradation of Cr3C2-NiCr coating prepared by the HVOF technique10.2478/kom-2013-0009 ↗
6. Tribological and corrosion behavior of HVOF sprayed WC-Co, NiCrBSi and Cr3C2-NiCr coatings and analysis using design of experiments
7. Development of high carbide dissolution/low carbon loss Cr3C2-NiCr coatings by shrouded plasma spraying10.1016/j.surfcoat.2014.07.062 ↗
8. Improving the high temperature abrasion resistance of thermally sprayed Cr3C2-NiCr coatings by WC addition10.1016/j.surfcoat.2018.01.035 ↗
9. Sliding wear behavior of thermally sprayed 75/25 Cr3C2/NiCr wear resistant coatings10.1016/0043-1648(96)06983-9 ↗
10. High temperature erosion–oxidation of Cr3C2–NiCr thermal spray coatings under simulated turbine conditions10.1016/j.corsci.2013.01.030 ↗
11. Cr3C2-NiCr and WC-Ni thermal spray coatings as alternatives to hardchromium for erosion-corrosion resistance10.1016/j.surfcoat.2007.06.048 ↗
12. Effects of thickness coating on the electrochemical behavior of thermal spray Cr3C2-NiCr coatings10.1016/S0257-8972(01)01679-6 ↗
13. Performance of high-velocity oxyfuel-sprayed coatings on an Fe-based superalloy in Na2SO4-60%V2O5 environment at 900 °C part II: hot corrosion behavior of the coatings10.1361/105994906X83411 ↗
14. High-temperature corrosion behaviour of air plasma sprayed Cr3C2-25NiCr and NiCrMoNb powder coating on alloy 80A at 900 °C10.1016/j.surfcoat.2018.01.011 ↗
15. Review of thermal spray coating applications in the steel industry: Part 1-hardware in steel making to the continuous annealing process10.1007/s11666-010-9518-8 ↗
16. A Comparative study to evaluate the Corrosion performance of Zr incorporated Cr3C2-(NiCr) coating at 900 °C10.1016/j.ceramint.2018.01.047 ↗
17. Processing effects on porosity-property correlations in plasma sprayed yttria-stabilized zirconia coatings10.1016/S0921-5093(03)00342-3 ↗
18. Berndt · 2014 · 267
19. Effect of spraying powders size on the microstructure, bonding strength, and microhardness of MoSi2 coating prepared by air plasma spraying10.1007/s11666-014-0120-3 ↗
20. Effect of heat treatment on friction and abrasive wear behavior of WC-12Co and Cr3C2-25NiCr coatings10.1016/j.triboint.2017.10.017 ↗
21. Hot corrosion studies of HVOF sprayed Cr3C2-NiCr and Ni–20Cr coatings on nickel-based superalloy at 900°C10.1016/j.surfcoat.2005.12.030 ↗
22. Microstructure and mechanical properties of HVOF sprayed nanorystalline Cr3C2-25 (Ni20Cr) coating10.1361/105996306X124374 ↗
23. The role of microstructure in the high temperature oxidation mechanism of Cr3C2–NiCr composite coatings10.1016/j.corsci.2009.02.027 ↗
24. High temperature oxidation studies of detonation-gun-spray Cr3C2–NiCr coating on Fe-and Ni-based superalloys in air under cyclic condition at 900°C10.1016/j.jallcom.2008.04.087 ↗
25. Hot corrosion of materials: a fluxing mechanism10.1016/S0010-938X(01)00057-9 ↗
26. Na2SO4-induced accelerated oxidation (hot corrosion) of nickel10.1007/BF02642794 ↗
27. Hot corrosion of modified Ti3Al-based alloy coated with thin Na2SO4 film at 910 and 950 °C in air10.1016/S1003-6326(17)60111-0 ↗