Comparative study on tribological and corrosion protection properties of plasma sprayed Cr2O3-YSZ-SiC ceramic coatings
Source abstract
Abstract
Abstract In this research, the tribological and corrosion protection properties of atmospheric plasma sprayed Cr 2 O 3 -20YSZ (CZ) and Cr 2 O 3 -20YSZ-10SiC (CZS) composite coatings on 304L stainless steel substrates were evaluated and compared to pure Cr 2 O 3 (C) coating. Microstructural evaluations were carried out using an optical microscopy, X-ray diffraction (XRD) analysis, and a Field Emission Scanning Electron Microscopy (FE-SEM) equipped with Energy Dispersive X-ray Spectroscopy (EDS). The ball-on-disk wear test was performed using an alumina counterpart at room temperature. The protective efficiency of the coatings with/without sealing treatment was evaluated by electrochemical potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in a 3.5 wt% NaCl solution. Evaluation of wear tracks showed that enhancement of the wear resistance of the composite coatings was ascribed to the zirconia phase transformation toughening and the presence of more ductile tribofilms participated in pore filling during the wear. The corrosion measurements revealed that the protection properties of the coatings were strongly dependent on the porosity content so that the as-sprayed coatings due to their porous nature could not protect the substrate. However, filling the porosity using an epoxy sealant prevented the penetration of the corrosive environment into the substrate and therefore increased the protective efficiency of the coatings. Moreover, the density of the unfilled defects such as micro-cracks determines the protection properties of the sealed coatings, so that the CZ coating due to its highest toughness had the lowest micro-crack density and thus the highest protective efficiency.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (80)
Show source-provided references
1. Role of thermal spray coatings on wear, erosion and corrosion behavior: a review
2. Processing of alumina–zirconia composites by surface modification route with enhanced hardness and wear resistance10.1016/j.ceramint.2014.09.006 ↗
3. Plasma thermal spray of ceramic oxide coating on carbon steel with enhanced wear and corrosion resistance for oil and gas applications10.1016/j.ceramint.2014.06.017 ↗
4. Comparative study of the corrosion resistance of thermally sprayed ceramic coatings and their bulk ceramic counterparts10.1016/j.jeurceramsoc.2013.08.033 ↗
5. Comparative study on the corrosion and wear behavior of plasma-sprayed vs. high velocity oxygen fuel-sprayed Al8Si20BN ceramic coatings10.1016/j.ceramint.2018.03.275 ↗
6. Microstructure, phase composition and mechanical properties of plasma sprayed Al2O3, Cr2O3 and Cr2O3-Al2O3 composite coatings10.1016/j.surfcoat.2017.03.022 ↗
7. Mechanical properties of plasma sprayed nanostructured TiO2 coatings on mild steel10.1016/j.ceramint.2013.12.036 ↗
8. Corrosion behavior of plasma sprayed ceramic and metallic coatings on carbon steel in simulated seawater10.1016/j.matdes.2013.06.002 ↗
9. Microstructure and properties of Cr2O3 coating deposited by plasma spraying and dry-ice blasting10.1016/j.surfcoat.2013.03.016 ↗
10. Correlation between microstructure, chemical components and tribological properties of plasma-sprayed Cr2O3-based coatings10.1016/j.ceramint.2018.03.004 ↗
11. The Effect of deposition parameters on the structure and mechanical properties of chromium oxide coatings deposited by reactive magnetron sputtering10.3390/coatings8030111 ↗
12. Effect of addition of multimodal YSZ and SiC powders on the mechanical properties of nanostructured Cr2O3 plasma-sprayed coatings10.1007/s11666-019-00834-8 ↗
13. Thermal and mechanical properties of nano-YSZ–Alumina functionally graded coatings deposited by nano-agglomerated powder plasma spraying10.1016/j.ceramint.2014.05.068 ↗
14. Wear of plasma sprayed conventional and nanostructured Al2O3 and Cr2O3 based coatings10.1007/s12666-011-0070-0 ↗
15. Wear resistance of chromium oxide nanostructured coatings10.1016/j.ceramint.2008.02.022 ↗
16. Deconvolving ferroelastic and phase transformation toughening in Pb(Zr1-xTix)O3 and Pb1-yLay(Zr1-xTix)O310.1111/jace.12007 ↗
17. High-temperature fracture toughness of mullite with monoclinic zirconia10.1111/jace.14637 ↗
18. An Overview on the improvement of mechanical properties of ceramics nanocomposites10.1155/2015/106494 ↗
19. Mechanical properties and the microstructure of the plasma-sprayed ZrO2Y2O3/ZrO2Y2O3CoNiCrAlY/CoNiCrAlY coating
20. Properties of Al2O3–40 wt.% ZrO2 composite coatings from ultra-fine feedstocks by atmospheric plasma spraying10.1016/j.wear.2008.03.019 ↗
21. Microstructure and wear behaviour of powder and suspension hybrid Al2O3–YSZ coatings10.1016/j.ceramint.2018.02.048 ↗
22. Fabrication and abrasive wear behavior of ZrO2-SiC-Al2O3 ceramic10.1016/j.ceramint.2017.08.032 ↗
23. High temperature erosion behavior of spark plasma sintered ZrB2-SiC composites10.1016/j.ceramint.2017.04.039 ↗
24. Effect of sealing treatment on the corrosion resistance of thermal-sprayed ceramic coatings10.1016/j.surfcoat.2004.08.009 ↗
25. The effects of sealing on the mechanical properties of the plasma-sprayed alumina-titania coating10.1016/S0257-8972(00)01132-4 ↗
26. The effect of modified epoxy sealing on the electrochemical corrosion behaviour of reactive plasma-sprayed TiN coatings10.1016/j.corsci.2013.05.031 ↗
27. Effects of inorganic sealant and brief heat treatments on corrosion behavior of plasma sprayed Cr2O3-Al2O3 composite ceramic coatings10.1016/j.surfcoat.2015.06.045 ↗
28. Correlation between microstructural characteristics and abrasion wear resistance of sealed thermal-sprayed coatings10.1016/j.surfcoat.2005.07.092 ↗
29. Effect of test duration on impact/sliding wear damage of 304L stainless steel at room temperature: metallurgical and micromechanical investigations10.1016/S0043-1648(01)00521-X ↗
30. Influence of the quality and uniformity of ceramic coatings on corrosion resistance10.1016/j.ceramint.2014.12.087 ↗
31. Swank · 2000
32. Enhanced mechanical properties of yttrium doped ZnO nanoparticles as determined by instrumented indentation technique10.1016/j.ceramint.2018.03.038 ↗
33. Fracture toughness measurements of LPS-SiC: a comparison of the indentation technique and the SEVNB method10.1590/S1516-14392005000200004 ↗
34. Determination of fracture toughness using the area of micro-crack tracks left in brittle materials by Vickers indentation test10.1007/s40145-013-0047-z ↗
35. Fracture toughness of ceramics by the Vickers indentation crack length method: a critical review10.1002/9780470291313.ch5 ↗
36. Toughness evaluation of hard coatings and thin films10.1016/j.tsf.2011.09.036 ↗
37. Evaluation of indentation fracture toughness for brittle materials based on the cohesive zone finite element method10.1016/j.engfracmech.2014.11.013 ↗
38. Analysis methods and size effects in the indentation fracture toughness assessment of very thin oxide coatings on glass10.1016/j.crme.2011.05.009 ↗
39. Structural properties and corrosion resistance of tantalum nitride coatings produced by reactive DC magnetron sputtering10.1039/C6RA17869C ↗
40. The effect of interlayer on corrosion resistance of ceramic coating/Mg alloy substrate in simulated physiological environment10.1016/j.surfcoat.2012.05.088 ↗
41. Influence of micro-arc oxidation coatings on corrosion performances of az80 cast alloy10.20964/2018.08.38 ↗
42. 2015
43. Production of nano structured silicon carbide by high energy ball milling10.4314/ijest.v3i4.68544 ↗
44. Nanocrystalline ZrB2 powders prepared by mechanical alloying10.1016/j.jascer.2013.08.002 ↗
45. Mechanical activation-assisted combustion synthesis of in situ aluminum matrix hybrid (TiC/Al2O3) nanocomposite10.1016/j.ceramint.2016.07.219 ↗
46. Influences of atmospheric plasma spraying parameters on the porosity level of alumina coating on AZ31B magnesium alloy using response surface methodology10.1016/j.pnsc.2012.09.004 ↗
47. Thermal spray coating of porous nanostructured ceramic feedstock
48. Plasma sprayed ceramic coatings without and with epoxy resin sealing treatment and their wear resistance10.1016/j.wear.2007.01.005 ↗
49. Effect of nano-Si3N4 additives and plasma treatment on the dry sliding wear behavior of plasma sprayed Al2O3-8YSZ ceramic coatings10.1007/s11666-017-0540-y ↗
50. Friction reduction and wear resistance enhancement of SiC and Si3N4 ceramics under dry conditions10.1080/10402004.2015.1087081 ↗
51. Influence of surface roughness on the friction property of textured surface
52. Wear behaviour of nanostructured alumina–titania coatings deposited by atmospheric plasma spray10.1016/j.wear.2009.01.022 ↗
53. Fracture behaviour of ceramic–metallic glass gradient transition coating10.1016/j.ceramint.2018.12.015 ↗
54. Wear studies on plasma-sprayed Al2O3 and 8mole% of Yttrium-stabilized ZrO2 composite coating on biomedical Ti-6Al-4V alloy for orthopedic joint application
55. Correlation between mechanical properties with specific wear rate and the coefficient of friction of graphite/epoxy composites10.3390/ma8074162 ↗
56. Microhardness and wear resistance of Al2O3-TiB2-TiC ceramic coatings on carbon steel fabricated by laser cladding10.1016/j.ceramint.2018.09.140 ↗
57. Effect of microstructure and mechanical properties on wear behavior of plasma-sprayed Cr2O3-YSZ-SiC coatings10.1016/j.ceramint.2018.11.226 ↗
58. Microstructure and improved mechanical properties of Al2O3/Ba-β-Al2O3/ZrO2 composites with YSZ addition10.1016/j.jeurceramsoc.2018.07.036 ↗
59. Hutchings · 2017
60. Critical length scale controls adhesive wear mechanisms10.1038/ncomms11816 ↗
61. An Investigation of the markings on wear and fatigue fracture surfaces10.1016/0043-1648(82)90158-2 ↗
62. Failure analysis of a femoral hip stem made of stainless steel after short time of exposure10.2478/ama-2014-0026 ↗
63. Coatings Tribology: Properties, Mechanisms, Techniques and Applications in Surface Engineering
64. Tribological behavior of silicon carbide ceramics- a review
65. Wear and wear transition mechanisms of ceramics10.1016/0043-1648(95)06800-7 ↗
66. Tressler · 1984
67. Three-body abrasive wear of ceramic materials10.1016/0043-1648(94)90082-5 ↗
68. Plastic Deformation of aluminum oxide by indentation and abrasion10.1111/j.1151-2916.1971.tb12277.x ↗
69. Grain boundary sliding mechanism in plastic deformation of nano-grained YAG transparent ceramics: generalized self-consistent model and nanoindentation experimental validation10.1016/j.jeurceramsoc.2017.02.010 ↗
70. Orthodontic applications of biomaterials: a clinical guide
71. Jahanmir · 1993
72. Ultrafine ceramic grains embedded in metallic glass matrix: achieving superior wear resistance via increase in both hardness and toughness10.1021/acsami.8b02338 ↗
73. Effect of microstructure and mechanical properties on wear resistance of silicon nitride ceramics
74. McCafferty · 2010
75. Thermophysical behavior of thermal sprayed yttria stabilized zirconia based composite coatings10.1016/j.ceramint.2017.05.170 ↗
76. Effect of particle in-flight behavior on the microstructure and fracture toughness of YSZ TBCs prepared by plasma spraying10.3390/coatings8090309 ↗
77. Electrochemical investigation of chromium oxide-coated Ti-6Al-4V and Co-Cr-Mo alloy substrates10.1002/jbm.b.31861 ↗
78. Impedance parameters of nitrided 304L stainless steel in an acidified sulphate solution10.1016/S0022-0728(01)00634-9 ↗
79. EIS and XPS study of surface modification of 316LVM stainless steel after passivation10.1016/S0010-938X(98)00122-X ↗
80. Accurate electrochemical measurement of magnesium corrosion rates; a combined impedance, mass-loss and hydrogen collection study10.1016/j.electacta.2013.12.124 ↗