Effect of agglomeration and calcination temperature on the mechanical properties of yttria stabilized zirconia (YSZ)
Source abstract
Abstract
Abstract Effect of azeotropic distillation after co-precipitation process of powder synthesis on powders morphology and mechanical properties of yttria stabilized zirconia was studied. The formation of hard or soft agglomerates during drying or calcination of co-precipitated powder can easily be prevented through azeotropic distillation. The powder prepared by direct co-precipitation and azeotropic treatment after co-precipitation process was calcined at different temperatures and was characterized through X-ray diffraction, transmission electron microscope and BET surface area measurement. The calcined powders were compacted uniaxially and sintered in two step sintering process. Sintered, polished and thermally etched samples were observed under scanning electron microscope. Vickers hardness and indentation fracture toughness were estimated. It is observed that reasonably higher density with better hardness and fracture toughness can be achieved for azeotroped samples in same sintering condition. Azeotropic treatment increases the surface area almost three times which helps to achieve better sintering. Pin on disc wear tests against alumina disc at 20 N and 50 N loads up to 3000 m distance were carried out. The wear depth and coefficient of friction for both the material were compared.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Synthesis and characterisation of macroporous Yttria Stabilised Zirconia (YSZ) using polystyrene spheres as templates10.1016/j.micromeso.2008.07.018 ↗
2. Plasma spray synthesis of ultra-fine YSZ powder10.1016/j.jpowsour.2007.04.024 ↗
3. Thin yttrium-stabilized zirconia electrolyte solid oxide fuel cells by centrifugal casting10.1111/j.1151-2916.2002.tb00588.x ↗
4. Fabrication and properties of anode-supported tubular solid oxide fuel cells10.1016/j.jpowsour.2004.05.028 ↗
5. Fabrication and characteristics of anode supported flat-tube solid oxide fuel cell10.1016/S0378-7753(03)00431-2 ↗
6. Powder dispersion and tape casting of YSZ–NiO composite10.1023/B:JMSC.0000026934.88520.67 ↗
7. Characterisation of ZrO2–Y2O thermal barrier coatings by Raman spectroscopy10.1016/0040-6090(81)90014-6 ↗
8. Characterization of ZrO2–7wt% Y2O3 thermal barrier coatings with different porosities and FEM analysis of stress redistribution during thermal cycling of TBCs10.1016/S0257-8972(97)00486-6 ↗
9. Microstructural aspects of the sintering of thermal barrier coatings10.1016/j.msea.2003.11.018 ↗
10. Alumina and zirconia ceramics in joint replacements
11. The zirconia: a new dental ceramic material. An overview
12. Y-TZP ceramics for artificial joint replacements10.1016/S0142-9612(98)00064-7 ↗
13. Mechanical properties and short-term in-vivo evaluation of yttrium-oxide-partially-stabilized zirconia10.1002/jbm.820230105 ↗
14. Kang · 2005
15. Rahaman · 2003
16. Agglomerate and particle size effects on sintering yttria-stabilized zirconia10.1111/j.1151-2916.1981.tb09552.x ↗
17. Influence of agglomerate structures in ultra-fine substituted zirconia powders on compaction and sintering behaviour
18. Sintering and microstructure of ultrafine yttriazirconia compacts10.1007/BF00580150 ↗
19. Preparation and characterization of nanoscale Y-TZP powder by heterogeneous azeotropic distillation10.1007/BF00351566 ↗
20. Novel azeotropic distillation process for synthesizing nanoscale powders of yttria doped ceria electrolyte10.1016/S0167-577X(00)00265-2 ↗
21. Nanocrystalline zirconia powder processing through innovative wet-chemical methods10.1016/0965-9773(95)00074-7 ↗
22. Dispersion of ZrO2 particles in aqueous suspensions by ammonium polyacrylate10.1007/BF01148770 ↗
23. A critical evaluation of indentation techniques for measuring fracture toughness: I, direct crack measurements10.1111/j.1151-2916.1981.tb10320.x ↗
24. Y-TZP ceramics with optimized toughness: new results10.1016/j.jallcom.2004.02.014 ↗
25. Processing of nanocrystalline 8mol% yttria-stabilized zirconia by conventional, microwave-assisted and two-step sintering10.1016/j.msea.2008.03.023 ↗
26. Processing and sintering of ultrafine MgO–ZrO2 and (MgO, Y2O3)–ZrO2 powders10.1111/j.1151-2916.1990.tb09786.x ↗