Alternant phase distribution and wear mechanical properties of an Al 2 O 3 -40 wt%TiO 2 composite coating
Source abstract
Abstract
Abstract Al 2 O 3 -40 wt%TiO 2 (AT40) coating is a low-cost and widely applied ceramic coating. In this article, the phase distribution, micro-hardness and wear mechanism, as well as the spraying conditions optimization, are discussed. Interface defects. Phase distribution and phase composition were analysed using SEM and XRD. The results show that the pre-existing surface morphology mainly determines the phase distribution. Al 2 TiO 5 and γ-Al 2 O 3 are the main phases in the coating. In this experiment, the highest micro-hardness (1126.2 HV 0.2 ) was measured using a Vickers tester. Additionally, the wear rate of the highest micro-hardness coating is 0.0387 mg/N m, which is the lowest weight loss rate measured among all the samples. The wear mechanism for this sample is primarily scratches. In conclusion, the compact lamellar phase distribution decreases the number of interface defects, increases the hardness and determines the wear mechanism. Also, the phase distribution is affected by the spraying conditions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Metal and Thin Film Mechanics · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Microstructure development of Al2O3–13wt%TiO2 plasma sprayed coatings derived from nanocrystalline powders10.1016/S1359-6454(01)00414-1 ↗
2. Influence of spraying parameters on the microstructure and properties of plasma-sprayed Al2O3/40%TiO2 coating10.1016/j.phpro.2013.11.028 ↗
3. Preparing of nanostructured Al2O3–TiO2–ZrO2 composite powders and plasma spraying nanostructured composite coating10.1016/j.vacuum.2013.03.010 ↗
4. High-temperature self-lubricated properties of Al2O3/Mo laminated composites10.1016/j.wear.2012.01.010 ↗
5. Structure and surface properties of Al2O3–TiO2 ceramic coated AZ31 magnesium alloy10.1016/j.ceramint.2016.05.162 ↗
6. Effect of the initial particle size distribution on the properties of suspension plasma sprayed Al2O3–TiO2 coatings10.1016/j.surfcoat.2014.12.010 ↗
7. Effect of TiO2 addition on the microstructure and nanomechanical properties of Al2O3 suspension plasma sprayed coatings10.1016/j.apsusc.2014.07.168 ↗
8. High temperature tribological behavior of nanostructured and conventional plasma sprayed alumina-titania coatings10.1016/j.vacuum.2012.01.008 ↗
9. Indentation properties of plasma sprayed Al2O3–13% TiO2 nanocoatings10.1016/j.actamat.2009.03.020 ↗
10. Influence of composite powders' microstructure on the microstructure and properties of Al2O3–TiO2 coatings fabricated by plasma spraying10.1016/j.matdes.2014.09.078 ↗
11. Microstructural characterization of plasma sprayed conventional and nanostructured coatings with nitrogen as primary plasma gas10.1016/j.surfcoat.2013.07.069 ↗
12. Microstructure, mechanical properties and thermal shock resistance of plasma sprayed nanostructured zirconia coatings10.1016/j.ceramint.2011.04.024 ↗
13. On the relevance of microstructure in the fracture toughness of nanostructured alumina–13% titania coatings10.1016/j.surfcoat.2012.03.021 ↗
14. Fabrication and properties of plasma-sprayed Al2O3/TiO2 composite coatings: a role of nano-sized TiO2 addition10.1016/j.surfcoat.2009.10.052 ↗
15. Comparison of flame sprayed Al2O3-TiO2 coatings their microstructure, mechanical properties and tribology behavior10.1016/j.surfcoat.2006.02.011 ↗
16. Microstructure and tribological properties of nanostructured and conventional plasma sprayed alumina–titania coatings10.1016/j.surfcoat.2014.09.014 ↗
17. Design of experiments in thermal spraying: a review10.1016/j.surfcoat.2008.04.031 ↗
18. Optimization of plasma spray parameters on the mechanical properties of agglomerated Al2O3–13%TiO2 coated mild steel10.1016/j.matdes.2012.03.019 ↗
19. Mechanical properties of plasma sprayed nanostructured TiO2 coatings on mild steel10.1016/j.ceramint.2013.12.036 ↗
20. Influence of critical plasma spraying parameter (CPSP) on plasma sprayed Alumina–Titania composite coatings10.1016/j.ceramint.2009.07.012 ↗
21. Effect of APS process parameters on wear behaviour of alumina–titania coatings10.1016/j.matlet.2004.02.026 ↗
22. Effects of critical plasma spray parameter and spray distance on wear resistance of Al2O3–8wt%TiO2 coatings plasma-sprayed with nanopowders10.1016/j.surfcoat.2008.01.002 ↗
23. Influence of plasma spray parameters on formation and morphology of ZrO2–8wt%Y2O3 deposits10.1111/j.1151-2916.2001.tb00728.x ↗
24. Properties of the thermally sprayed Al2O3–TiO2 coating deposited on titanium substrate10.1016/j.ijrmhm.2015.03.009 ↗
25. Plasma thermal spray of ceramic oxide coating on carbon steel with enhanced wear and corrosion resistance for oil and gas applications10.1016/j.ceramint.2014.06.017 ↗
26. Optimization of biodiesel production from camelina oil using orthogonal experiment10.1016/j.apenergy.2011.04.041 ↗
27. Tribological properties of plasma sprayed alumina titania-coatings role and control of the microstructure10.1016/S0257-8972(99)00532-0 ↗
28. Effects of TiO2 on the mechanical properties of the Al2O3–TiO2 plasma sprayed coating10.1016/j.jeurceramsoc.2006.04.099 ↗
29. Wear behaviour of thermally sprayed ceramic oxide coatings10.1016/j.wear.2006.03.023 ↗
30. An improved Vickers indentation fracture toughness model to assess the quality of thermally sprayed coatings10.1016/j.engfracmech.2014.07.015 ↗
31. Mechanical and thermophysical properties of thick PYSZ thermal barrier10.1016/S0257-8972(98)00628-8 ↗
32. Further studies on the effect of stand-off distance on characteristics of plasma sprayed hydroxyapatite coating10.1016/S0257-8972(02)00166-4 ↗
33. Abrasive wear characteristics of plasma sprayed nanostructured alumina titania coatings10.1016/S0043-1648(99)00323-3 ↗