Comparison of microwave and conventional heating methods for oxidative stabilization of polyacrylonitrile fibers at different holding time and heating rate
Source abstract
Abstract
Abstract A microwave heating method was used for oxidative stabilization of polyacrylonitrile (PAN) fibers. The effect of holding time and heating rate on the oxidative stabilization process of PAN fibers at a specific temperature of 180 °C was investigated. The bulk density, chemical structure (FTIR), crystalline structure (WAXD), and microstructure (SEM) were investigated. The results show the dehydrogenation reaction in microwave oxidative stabilization was faster than conventional heating. Microwave heating effectively shortened the thermal stabilization time by 5 min and the rate is increased by 30–50% compared with the conventional thermal stabilization process. The degree of oxidative stabilization was increased by 0.035 at the heating rate of 20 °C/min, and increased by 0.047 at 15 min of incubation. As the holding time increases, the groove on the fiber surface becomes narrower and more compact. Compared with the conventional thermal stabilization process, the breaks in stabilized fibers obtained by microwave heating was fewer and the fractures are more flat. A holding time of 15 min and a heating rate of 20 °C/min was the optimum process.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fiber-reinforced polymer composites · Natural Fiber Reinforced Composites · Electromagnetic wave absorption materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Carbon fibers: precursor systems, processing, structure, and properties10.1002/anie.201306129 ↗
2. Wettability of carbon fibres at micro- and mesoscales10.1016/j.carbon.2017.05.055 ↗
3. Polyacrylonitrile-based nanofibers-a state-of-the-art review10.1016/j.progpolymsci.2011.07.001 ↗
4. Effect of carbonization time on the structure and electromagnetic parameters of porous-hollow carbon fibres10.1016/j.ceramint.2009.03.002 ↗
5. Co-deposition of carbon dots and reduced graphene oxide nanosheets on carbon-fiber microelectrode surface for selective detection of dopamine10.1016/j.apsusc.2017.03.257 ↗
6. High strength and high modulus carbon fibers10.1016/j.carbon.2015.05.016 ↗
7. Electron microscopy investigation of interface between carbon fiber and ultrahigh molecular weight polyethylene10.1016/j.jallcom.2012.12.045 ↗
8. Mechanical properties and densification of short carbon fiber-reinforced TiB2/C composites produced by hot pressing10.1016/j.jallcom.2013.09.004 ↗
9. Development of TORAYCA prepared P2302 carbon fiber reinforced plastic for aircraft primary structural materials10.1163/156855196X00301 ↗
10. Multifunctional structural supercapacitor composites based on carbon aerogel modified high performance carbon fiber fabric10.1021/am400947j ↗
11. Effect of carbonization temperature on the structure and microwave absorbing properties of hollow carbon fibers10.1016/j.ceramint.2011.02.017 ↗
12. Preparation, structure and supercapacitance of bonded carbon nanofiber electrode materials10.1016/j.carbon.2011.02.005 ↗
13. New aspects in the oxidative stabilization of PAN-based carbon fibers10.1016/S0008-6223(96)00094-2 ↗
14. A review of heat treatment on polyacrylonitrile fiber10.1016/j.polymdegradstab.2007.03.023 ↗
15. Comparison of microwave and conventional heating methods in carbonization of polyacrylonitrile-based stabilized fibers at different temperature measured by an in-situ process temperature control ring10.1016/j.polymdegradstab.2017.04.002 ↗
16. Synthesis of in situ network-like vapor-grown carbon fiber improved LiFePO4 cathode materials by microwave pyrolysis chemical vapor deposition10.1016/j.jallcom.2011.06.054 ↗
17. Effects of atmosphere on the microstructure and magnetic properties of strontium ferrites with microwave-assisted sintering10.1007/s10948-015-3117-3 ↗
18. X-Ray pole figure analysis and magnetic properties of microwave sintered Sr-M-type hexagonal ferrites10.1007/s10948-013-2110-y ↗
19. Electromagnetic and absorption properties of nano-sized and micro-sized Fe4N particles10.1016/j.jallcom.2015.10.005 ↗
20. H. Converters, I. Induction, K.H.T. Nhiên, Advances in induction and microwave heating of mineral and organic materials, Tailieu Vn, 2011.
21. A rapid method for the preparation of silica-coated ZrO2 nanoparticles by microwave irradiation10.1016/j.ceramint.2011.01.003 ↗
22. Microwave heating processes involving carbon materials10.1016/j.fuproc.2009.08.021 ↗
23. Microwave-assisted synthesis of Ce-doped ZnO/CNT composite with enhanced photo-catalytic activity10.1016/j.ceramint.2016.09.114 ↗
24. Effect of copolymerization and heat treatment on the structure and x-ray diffraction of polyacrylonitrile10.1002/pol.1983.180211103 ↗
25. Structure of PAN fibers and its relationship with resulting carbon fiber properties10.1016/0015-0568(81)90067-1 ↗
26. Characterization of oxidized PAN fibers10.1016/0008-6223(74)90007-4 ↗
27. Study on the oxidative stabilization of polyacrylonitrile fibers by microwave heating10.1016/j.polymdegradstab.2018.02.017 ↗
28. Yu · 2007
29. Influence of precursor properties on the thermal stabilization of polyacrylonitrile fibers10.1007/s00289-006-0629-9 ↗