Investigation of the solvent debinding in the injection molding of ZrO2 ceramics using LDEP, HDPE and wax binders
Source abstract
Abstract
Abstract In this paper, zirconia green parts with the binder system containing low density polyethylene (LDPE) were prepared by injection molding. The green parts after solvent and thermal debinding were sintered at 1500 °C for 2 h. The influences of LDPE on solvent debinding were emphatically studied. A new method was proposed to determine the extracting degree of the wax binders in comparison with the common method. The results showed that the solvent removable binders could not be extracted completely during the solvent debinding though the replacement of HDPE with LDPE promoted this process. The extracting degree of the wax binders was about 74–80% and increased with the increase of LDPE contents. In addition, it was also found that microcracks easily occurred in the green parts after the solvent debinding when using LDPE replacing HDPE, which may result in the decrease of the bending strength of the sintered samples.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Injection Molding Process and Properties · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Study of ZrO2 ceramic injection molding technology
2. Binder removal via a two-stage debinding process for ceramic injection molding parts10.1016/j.ceramint.2013.10.032 ↗
3. Two-stage sintering of nano-sized yttria stabilized zirconia process by powder injection moulding10.1016/j.jmatprotec.2007.04.097 ↗
4. Rheological properties of alumina feedstocks for the low-pressure injection moulding process10.1016/j.jeurceramsoc.2008.11.001 ↗
5. Influence of dispersant, storage time and temperature on the rheological properties of zirconia-paraffin feedstock for LPIM10.1016/j.jeurceramsoc.2009.12.003 ↗
6. Yttria stabilized zirconia formed by micro ceramic injection molding: rheological properties and debinding effects on the sintered part10.1016/j.ceramint.2012.09.033 ↗
7. Mutsuddy · 1995 · 178
8. Kneading behaviour and homogeneity of zirconia feedstocks for micro-injection molding10.1016/j.jeurceramsoc.2003.11.027 ↗
9. Injection moulding of tungsten carbide-nickel powders prepared by electroless deposition10.4028/www.scientific.net/KEM.545.148 ↗
10. The influence of powder loading and binder additive on the properties of alumina injection-moulding blends10.1007/BF01171549 ↗
11. Rheological modeling of strontium ferritefeedstock for magnetic powder injection molding10.1016/j.powtec.2014.04.073 ↗
12. Effects of different backbone binders on the characteristics of zirconia parts using wax-based binder system via ceramic injection molding10.1007/s40145-016-0205-1 ↗
13. Yield behavior of zirconia-wax suspensions10.1016/S0921-5093(98)00699-6 ↗
14. Binder system for micropowder injection molding10.1016/S0167-577X(00)00276-7 ↗
15. Specific interactions of low molecular weight analogues of carnauba wax and polyethylene glycol binders of ceramic injection moulding feedstocks10.1016/j.ceramint.2014.11.082 ↗
16. Effect of microcrystalline wax on the solvent debinding of the Sr-ferrite ceramics prepared by powder injection molding10.1016/j.jeurceramsoc.2016.12.026 ↗
17. Guide to injection moulding of ceramics and hardmetals: special consideration of fine powder10.1179/pom.1998.41.1.41 ↗
18. Mixing and characterization of feedstock for powder injection molding10.1016/S0167-577X(00)00151-8 ↗
19. Ceramic injection moulding: influence of specimen dimensions and temperature on solvent debinding kinetics10.1016/j.jmatprotec.2004.06.008 ↗
20. Review on debinding technique in metal injection molding
21. Thermal removal of multicomponent binder from ceramic injection mouldings10.1016/S0955-2219(02)00015-8 ↗
22. The rheological characterization of PIM feedstocks at low shear rates
23. Influence of paraffin wax characteristics on the formulation of wax-based binders and their debinding from green molded parts using two comparative techniques10.1016/j.jmatprotec.2009.07.018 ↗
24. Partially water-soluble binder formulation for injection molding submicrometer zirconia10.1023/A:1008681920391 ↗
25. An investigation of co-crystallization in LDPE/HDPE blends using DSC and TREF 110.1016/S0040-6031(97)00465-6 ↗
26. Effect of preparation methods and condition of precursors on the phase composition of yttria-stabilized zirconia powders
27. Sintering behavior and mechanical properties of injection-molded zirconia powder10.1016/j.ceramint.2003.09.009 ↗