Investigation of machinability in milling of Inconel 718 with solid Sialon ceramic tool using supercritical carbon dioxide (scCO2)-based cooling conditions
Source abstract
Abstract
Abstract Milling of hard-to-machining materials is still a challenge since the high cutting temperature caused by the cooling lubrication problems and the property of materials. This paper proposes the use of supercritical carbon dioxide (scCO2), supercritical carbon dioxide based minimum quantity lubrication cutting fluid (scCO2-MQL), and supercritical carbon dioxide based minimum quantity lubrication with oil droplets cutting fluid (scCO2-OoW) as the eco-friendly cooling-lubrication methods for milling of Inconel 718 superalloy. The cutting forces, cutting temperatures, surface roughness, surface topographies, subsurface characteristics and tool wear were performed to quantify the effect of various cooling methods. The results indicated that the application of scCO2-based cooling conditions was an effective cooling and lubrication technology for the ceramic tool since it could reduce the cutting force and temperature and improve the surface finish with lower peaks and valleys dispersion compared with other cooling conditions. Compared with the scCO2-MQL, only scCO2 and dry milling conditions, the topographies of machined surface under the scCO2-OoW condition have been significantly improved. Furthermore, the scCO2-OoW cooling technique has facilitated the removal of debris adhering to the ceramic tool and improved lubrication of the cutting zone.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Injection Molding Process and Properties · Advanced Machining and Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. Influences of tool structure, tool material and tool wear on machined surface integrity during turning and milling of titanium and nickel alloys: a review10.1007/s00170-018-2314-1 ↗
2. Dry machining of Inconel 718, workpiece surface integrity10.1016/j.jmatprotec.2011.04.011 ↗
3. End milling of Inconel 718 using solid Si3N4 ceramic cutting tools10.1016/j.procir.2019.03.280 ↗
4. Cutting performance, failure mechanisms and tribological properties of GNPs reinforced Al2O3/Ti(C,N) ceramic tool in high speed turning of Inconel 71810.1016/j.ceramint.2020.04.206 ↗
5. Evaluation of an environment-friendly turning process of Inconel 601 in dry conditions10.1016/j.jclepro.2020.121919 ↗
6. Influences of milling and grinding on machined surface roughness and fatigue behavior of GH4169 superalloy workpieces10.1016/j.cja.2017.07.013 ↗
7. Laser-induced oxidation-assisted micromilling of deep narrow microgroove on Inconel 71810.1007/s00170-021-06854-5 ↗
8. Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide10.1016/j.cja.2020.08.011 ↗
9. Study on laser-induced oxidation modification coupled with micro milling of WC-Co cemented carbide10.1016/j.ceramint.2019.12.218 ↗
10. Investigation of tool wear in the turning of Inconel 718 superalloy in terms of process performance and productivity enhancement10.1016/j.triboint.2017.10.005 ↗
11. Analysis of tool wear patterns in finishing turning of Inconel 71810.1016/j.wear.2012.11.004 ↗
12. State-of-the-art of surface integrity induced by tool wear effects in machining process of titanium and nickel alloys: a review10.1016/j.measurement.2018.09.045 ↗
13. Performance of graded nano-composite ceramic tools in ultra-high-speed milling of Inconel 71810.1007/s00170-012-4693-z ↗
14. Cutting temperature measurement using an improved two-color infrared thermometer in turning Inconel 718 with whisker-reinforced ceramic tools10.1016/j.ceramint.2018.07.142 ↗
15. Influence of process parameters on the cutting performance of SiAlON ceramic tools during high-speed dry face milling of hardened Inconel 71810.1007/s00170-019-04210-2 ↗
16. Analysis of the influence of nitrogen phase and surface heat transfer coefficient on cryogenic machining performance10.1016/j.jmatprotec.2016.02.003 ↗
17. PVD AlTiN coating effects on tool-chip heat partition coefficient and cutting temperature rise in orthogonal cutting Inconel 71810.1016/j.ijheatmasstransfer.2020.120449 ↗
18. Tool wear and chip morphology in high-speed milling of hardened Inconel 718 under dry and cryogenic CO2 conditions10.1016/j.wear.2019.01.095 ↗
19. CO2 cryogenic milling of Inconel 718: cutting forces and tool wear10.1016/j.jmrt.2020.05.118 ↗
20. Surface integrity in cryogenic machining of nickel based alloy—inconel 71810.1016/j.jmatprotec.2010.12.013 ↗
21. Environment friendly machining of inconel 625 under nano-fluid minimum quantity lubrication (NMQL)10.1007/s12541-018-0196-7 ↗
22. Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions10.1016/j.jclepro.2012.03.014 ↗
23. Performances of different eco-friendly nanofluid lubricants in the milling of Inconel X-750 superalloy10.1016/j.triboint.2019.04.042 ↗
24. Comparative analysis of dry, flood, MQL and cryogenic CO2 techniques during the machining of 15-5-PH SS alloy10.1016/j.triboint.2020.106196 ↗
25. Feasibility of metalworking fluids delivered in supercritical carbon dioxide10.1016/S1526-6125(06)70101-3 ↗
26. Performance of supercritical carbon dioxide sprays as coolants and lubricants in representative metalworking operations10.1016/j.jmatprotec.2012.07.020 ↗
27. Vegetable oil-based nanofluid minimum quantity lubrication turning: academic review and perspectives10.1016/j.jmapro.2020.09.044 ↗
28. Roles of new bio-based nanolubricants towards eco-friendly and improved machinability of Inconel 718 alloys10.1016/j.triboint.2019.106106 ↗
29. Effects of Minimum Quantity Lubrication (MQL) in machining processes using conventional and nanofluid based cutting fluids: a comprehensive review10.1016/j.jclepro.2016.03.146 ↗
30. Tool wear in Ti-6Al-4V alloy turning under oils on water cooling comparing with cryogenic air mixed with minimal quantity lubrication10.1007/s00170-015-7062-x ↗
31. Effect of different oil-on-water cooling conditions on tool wear in turning of compacted graphite cast iron10.1016/j.jclepro.2017.02.014 ↗
32. Sustainability-based performance evaluation of hybrid nanofluid assisted machining10.1016/j.jclepro.2020.120541 ↗
33. A review on recent development of minimum quantity lubrication for sustainable machining10.1016/j.jclepro.2020.122165 ↗
34. Influence of the condition of the surface layer of a hob cutter sharpened using the MQL-CCA hybrid method of coolant provision on its operational wear10.1007/s00170-018-2379-x ↗
35. Influence of application of hybrid MQL-CCA method of applying coolant during hob cutter sharpening on cutting blade surface condition10.1016/j.jclepro.2017.10.059 ↗
36. Evaluation of tool wear, surface roughness/topography and chip morphology when machining of Ni-based alloy 625 under MQL, cryogenic cooling and CryoMQL10.1016/j.jmrt.2019.12.069 ↗
37. Experimental comparison of the performance of nanofluids, cryogenic and hybrid cooling in turning of Inconel 62510.1016/j.triboint.2019.05.014 ↗
38. Rough turning Inconel 750 with supercritical CO2-based minimum quantity lubrication10.1016/j.jmatprotec.2013.10.003 ↗
39. Performance of supercritical carbon dioxide (scCO2) mixed with oil-on-water (OoW) cooling in high-speed milling of 316L stainless steel10.1016/j.procir.2018.08.301 ↗
40. Machining of nickel-base, Inconel 718, alloy with ceramic tools under finishing conditions with various coolant supply pressures10.1016/j.jmatprotec.2005.02.144 ↗
41. High-pressure cooling in turning of inconel 625 with ceramic cutting tools10.1016/j.procir.2018.08.221 ↗
42. New observations on wear mechanism of self-reinforced SiAlON ceramic tool in milling of Inconel 71810.1016/j.acme.2016.12.011 ↗
43. Effect of cutting speed on cutting forces and wear mechanisms in high-speed face milling of Inconel 718 with Sialon ceramic tools10.1007/s00170-013-5206-4 ↗
44. Surface integrity of INCONEL 718 turned under cryogenic conditions at high cutting speeds10.1007/s00170-019-03946-1 ↗
45. Turning of Inconel 718 with whisker-reinforced ceramic tools applying vegetable-based cutting fluid mixed with solid lubricants by MQL10.1016/j.jmatprotec.2018.11.032 ↗
46. Wear behaviour of whisker-reinforced ceramic tools in the turning of Inconel 718 assisted by an atomized spray of solid lubricants10.1016/j.triboint.2020.106235 ↗
47. High-pressure cooling in turning of inconel 625 with ceramic cutting tools10.1016/j.procir.2018.08.221 ↗
48. Machinability performance of nickel alloy X-750 with SiAlON ceramic cutting tool under dry, MQL and hBN mixed nanofluid-MQL10.1016/j.triboint.2020.106673 ↗
49. Experimental investigation of work hardening, residual stress and microstructure during machining Inconel 71810.1007/s12206-017-0926-2 ↗
50. Improved machinability of TiB2–TiC ceramic composites via laser-induced oxidation assisted micro-milling10.1016/j.ceramint.2020.12.280 ↗
51. Vignesh · 2020 · 243
52. Hybrid processes in manufacturing10.1016/j.cirp.2014.05.003 ↗
53. Tool wear and machined surface characteristics in side milling Ti6Al4V under dry and supercritical CO2 with MQL conditions10.1016/j.triboint.2020.106511 ↗
54. Finite element simulation of high-speed cutting forces10.1016/j.jmatprotec.2006.02.019 ↗
55. Chapter 2 - performance of Sialon/Si3N4 graded ceramic tools at high speed machining
56. Tool wear and surface integrity of inconel 718 in dry and cryogenic coolant at high cutting speed10.1016/j.wear.2017.01.031 ↗
57. An investigation of surface damage in the high speed turning of Inconel 718 with use of whisker reinforced ceramic tools10.1016/j.jmatprotec.2011.09.022 ↗
58. Investigation of machinability in turning of difficult-to-cut materials using a new cryogenic cooling approach10.1016/j.triboint.2017.11.033 ↗
59. High speed ball nose end milling of inconel 71810.1016/S0007-8506(07)62892-3 ↗