Interfacial characteristics and wear performances of iron matrix composites reinforced with zirconia-toughened alumina ceramic particles
Source abstract
Abstract
Abstract Zirconia-toughened alumina ceramic particle (ZTAP)-reinforced high Cr cast Fe matrix composites (ZTAP/Fe composites) are promising advanced wear-resistant materials. However, due to wear and tear, the ceramic particles may shed from the Fe matrix because of their low interfacial bonding properties. In the present work, we investigated interfacial characteristics and abrasive wear behaviours of ZTAP/Fe composites. Results showed that sintering played a significant role in the formation of sintering necks and consequently affected both compressive strengths and porosities of ZTA ceramic preforms. Optimum compressive strength (44.3 MPa) and porosity (25.2%) were obtained when sintering was performed at 1350 °C for 1 h. Subsequently, ZTAP/Fe composites without evident defects were fabricated by infiltration casting. Scanning electron microscopy, electron probe microanalysis and transmission electron microscopy were also used to analyse the microstructures and phase constituents of the interfacial layers of composites. Effects of applied wear loads on the wear behaviour evolutions and wear mechanisms of composites were examined. Wear resistances of ZTAP/Fe composites were found to be 1.64–2.21 times as compared to the Cr15 specimen.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Effect of nanoscale V2C precipitates on the three-body abrasive wear behavior of high-Mn austenitic steel
2. Understanding effects of Cr content on the slurry erosion behavior of high-Cr cast irons through local property mapping and computational analysis10.1016/j.wear.2016.12.031 ↗
3. On the evaluation of certain strength characteristics and fracture features of iron-based sintered MMCs with nanooxide additives10.1016/j.msea.2019.04.044 ↗
4. Three-Body abrasive wear behavior of CC/high-Cr WCI composite and its interfacial characteristics10.1016/j.wear.2009.09.001 ↗
5. Characterization of interfacial layer of ZTA ceramic particles reinforced iron matrix composites10.1016/j.jallcom.2018.01.199 ↗
6. Microstructure and mechanical properties of Fe matrix composites reinforced by nickel-chromium double-layer coated ZTAP ceramics10.1016/j.ceramint.2020.03.284 ↗
7. Review on research progress of steel and iron wear-resistant material
8. Effect of titanium binder addition on the interface structure and three-body abrasive wear behavior of ZTA ceramic particles-reinforced high chromium cast iron10.1016/j.ceramint.2020.02.169 ↗
9. Interfacial bonding and abrasive wear behavior of iron matrix composite reinforced by ceramic particles10.3390/ma12223646 ↗
10. Adhesion in aluminum oxide-metal systems
11. Adhesion at metal-ZrO2 interfaces10.1016/j.surfrep.2006.03.002 ↗
12. Comparison of properties and impact abrasive wear performance of ZrO2-Al2O3/Fe composite prepared by pressure casting and infiltration casting process10.1016/j.triboint.2019.105979 ↗
13. Interface transition layer interaction mechanism for ZTAP/HCCI composites10.1515/secm-2016-0332 ↗
14. Significance of sensitization process in electroless deposition of Ni on nanosized Al2O3 powders10.1016/j.ceramint.2015.11.137 ↗
15. Different superplastic deformation behavior of nanocrystalline Ni and ZrO2/Ni nanocomposite10.1016/j.matlet.2007.06.048 ↗
16. Sub-micron Co-Al2O3 composite powders prepared by room-temperature ultrasonic-assisted electroless plating
17. Effect of the dispersibility of ZrO2 nanoparticles in Ni-ZrO2 electroplated nanocomposite coatings on the mechanical properties of nanocomposite coatings10.1016/j.apsusc.2005.05.076 ↗
18. Solid state bonding of Al2O3 with Cu, Ni and Fe: characteristics and properties10.1023/A:1004397019927 ↗
19. Three-body abrasive wear resistance of iron matrix composites reinforced with ceramic particles10.1177/1350650113496700 ↗
20. Preparation and mechanism of active Mo-Mn metallization on ZTA particles surface and interfacial bonding of reinforced iron matrix composite
21. Preparation of nickel coating on ZTA particles by electroless plating10.1016/j.ceramint.2018.03.055 ↗
22. Wettability and interaction mechanism for Ni-modified ZTA particles reinforced iron matrix composites10.1016/j.jallcom.2019.01.342 ↗
23. Microstructure and mechanical properties of Cu-ZTA cermet prepared by vacuum hot pressing sintering10.1088/2053-1591/ab6c19 ↗
24. Effects of chromium on the interface and bond strength of metal-ceramic joints10.1016/S0254-0584(02)00072-X ↗
25. The role of Cr on oxide formation in Ni-Cr alloys: a theoretical study10.1016/j.commatsci.2017.09.056 ↗
26. Experiments and calculations on refining mechanism of NbC on primary M7C3 carbide in hypereutectic Fe-Cr-C alloy10.1016/j.jallcom.2017.04.167 ↗
27. Formation of eutectic carbides in Fe-Cr-Mo-C alloy during non-equilibrium crystallization10.1016/j.matdes.2016.01.028 ↗
28. Ab initio-based diffusion theory and tracer diffusion in Ni-Cr and Ni-Fe alloys10.1016/j.jnucmat.2010.08.003 ↗
29. Elastic properties of binary NiAl, NiCr and AlCr and ternary Ni2AlCr alloys from molecular dynamic and Abinitio simulation10.1016/j.commatsci.2004.12.011 ↗
30. Influence of heat treatments on the microstructure as well as mechanical and tribological properties of NiCrAlY-Mo-Ag coatings10.1016/j.jallcom.2016.06.075 ↗
31. Microstructural evolution of carbides and its effect on tribological properties of SAPS or HVOF sprayed NiCr-Cr3C2 coatings10.1016/j.jallcom.2019.06.291 ↗
32. Tribological properties of NiCr-ZrO2(Y2O3)-SrSO4 composites at elevated temperatures10.1016/j.ceramint.2016.05.071 ↗
33. Processing, microstructure and mechanical properties of Al2O3-Cr nanocomposites10.1016/j.jeurceramsoc.2006.05.093 ↗
34. Influences of substrate pretreatments and Ti/Cr interlayers on the adhesion and hardness of CrAlSiN and TiAlSiN films deposited on Al2O3 and ZrO2-8Y2O3 thermal barrier coatings10.1016/j.rinp.2019.02.048 ↗
35. Mechanical and tribological properties of NiCr-Al2O3 composites at elevated temperatures10.1016/j.triboint.2014.11.023 ↗
36. Microstructure and oxidation behavior of NiCr-chromium carbides coating prepared by powder-fed laser cladding on titanium aluminide substrate10.1016/j.ceramint.2019.09.139 ↗
37. Development and use of an abrasion test for cast irons and steels
38. The wear of metals by hard abrasives10.1016/0043-1648(67)90093-2 ↗
39. Effective easing of the side effects of copper intrauterine devices using ultra-fine-grained Cu-0.4Mg alloy10.1016/j.actbio.2021.04.037 ↗
40. Ab initio-based diffusion theory and tracer diffusion in Ni-Cr and Ni-Fe alloys10.1016/j.jnucmat.2010.08.003 ↗
41. Effects of Sr addition on microstructure, mechanical and corrosion properties of biodegradable Mg-Zn-Ca alloy10.1016/j.jallcom.2020.155611 ↗
42. Confidence intervals for the power of Student's t-test10.1016/j.spl.2005.03.003 ↗
43. Effect of interface layers formed during dry sliding of zirconia toughened alumina (ZTA) and monolithic alumina against steel10.1016/0043-1648(95)06754-X ↗
44. Development of flank wear prediction model of zirconia toughened alumina (ZTA) cutting tool using response surface methodology10.1016/j.ijrmhm.2010.12.001 ↗
45. Effect of grain size and amount of zirconia on the physical and mechanical properties and the wear resistance of zirconia-toughened alumina10.1016/j.ceramint.2019.12.180 ↗
46. Advanced ceramic components: materials, fabrication, and applications10.1016/j.jiec.2020.02.002 ↗