Effects of HPDC processing parameters and gating design on microstructure and properties of FeCoNiCrAl-particle-reinforced Al–Si composites
Source abstract
Abstract
Thin-wall Al–Si components reinforced with 2 wt.% FeCoNiCrAl HEA particles were produced by HPDC. The results show that, at a constant intensification pressure of 50 MPa, increasing the casting temperature from 690 to 730°C leads to coarsening of Fe-rich phases and eutectic Si, whereas 710°C provides a balance between melt fluidity and high cooling rate, promoting the cooperative refinement of secondary solidification grains (SSGs) and externally solidified grains (ESGs) and minimising shrinkage sensitivity. HEA particles form flat and dense metallurgical interfaces with the Al–Si matrix, and Mg 2 Si enrichment is observed at the particle surfaces in the last-to-freeze regions. Increasing the intensification pressure from 20 to 80 MPa further refines α-Al grains and Fe-/Si-rich second phases and significantly enhances solidification feeding. An intensification pressure of 80 MPa reduces the total porosity to ∼0.21 %, markedly lowers the shrinkage-pore fraction, and leaves residual defects dominated by fine, blunt gas pores with an average sphericity of ∼0.58. Under identical HPDC conditions, the single-runner gating system produces overall finer grains and a much lower volume fraction of shrinkage cavities than the double-runner system, albeit at the cost of a higher proportion of gas pores, while the double-runner system is dominated by shrinkage defects. Consequently, the H-type system achieves an as-cast, heat-treatment-free strength–ductility combination of YS≈207 MPa, UTS≈398.1 MPa and EL≈8.2 %. The strength is mainly governed by matrix strengthening and the overall porosity level, whereas the elongation is exponentially sensitive to the “effective defect size.”
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Innovative hybrid high-pressure die-casting process for load-bearing body-in-white structural components10.1007/s40962-024-01280-1 ↗
2. The local squeeze technology for challenging aluminium HPDC automotive components
3. Mechanical Properties of a Structural Component Processed in High-Pressure Die Casting (HPDC) with a Non-Heat-Treated Aluminum Alloy10.3390/met14030369 ↗
4. Effect of super vacuum assisted high pressure die casting on the repeatability of mechanical properties of Al–Si–Mg–Mn die-cast alloys10.1016/j.jmatprotec.2018.10.030 ↗
5. Characterization on the formation of porosity and tensile properties prediction in die casting Mg alloys10.1016/j.jma.2020.12.006 ↗
6. Fabrication of aluminum matrix composite reinforced with Al0.5CoCrCuFeNi high-entropy alloy particles
7. Investigations on composites reinforced with HEA particles10.1088/1757-899X/227/1/012021 ↗
8. Tribological and mechanical properties of Al7075 metal matrix composite reinforced with CoMoMnNiV High Entropy alloy particles
9. Development and characterization of CrCoNi medium entropy alloy particles reinforced aluminum matrix composite10.3390/cryst12101452 ↗
10. Evolution of microstructure and mechanical properties of LM25-HEA composite processed through stir casting with a bottom pouring system10.3390/ma15010230 ↗
11. Influence of cantor alloy particles on microstructure, and wear behavior of aluminum metal matrix composite
12. AA1050 metal matrix composites reinforced by high-entropy alloy particles via stir casting and subsequent rolling10.1016/j.jallcom.2021.162370 ↗
13. Solid solution strengthening mechanism in high pressure die casting Al–Ce–Mg alloys10.1016/j.msea.2021.141109 ↗
14. Influence of injection parameters on the porosity and tensile properties of high-pressure die cast Al-Si alloys: a review10.1007/BF03355601 ↗
15. Influence of porosity characteristics on the variability in mechanical properties of high pressure die casting (HPDC) AlSi7MgMn alloys
16. Experimental and optimization of die casting parameters on Al-Si alloy with snail shell reinforcing agent
17. Influence of gating system parameters of die-cast molds on properties of Al-Si castings10.3390/ma14133755 ↗
18. Gating system optimization of high pressure die casting thin-wall AlSi10MnMg longitudinal load-bearing beam based on numerical simulation10.1007/s41230-018-8052-z ↗
19. The effects of varying Mg and Si levels on the microstructural inhomogeneity and eutectic Mg2Si morphology in die-cast Al-Mg-Si alloys10.1007/s10853-018-03198-6 ↗
20. Development of high strength and toughness non-heated al-mg-si alloys for high-pressure die-casting
21. Microstructure evolution and mechanical properties of new die-cast Al-Si-Mg-Mn alloys
22. Macro-heterogeneities in microstructures, concentrations, defects and tensile properties of die cast Al-Mg-Si alloys
23. Otarawanna · 2009
24. Simulation of alpha-Al grain formation in high vacuum die-casting Al-Si-Mg alloys with multi-component quantitative cellular automaton method10.1007/s41230-022-1176-1 ↗
25. Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method
26. Effect of multidirectional isothermal forging on microstructure and mechanical properties in Ti-6Al-4V alloy10.3390/ma15093156 ↗
27. Effects of high pressure on Fe-Rich phases and mechanical properties of Al-14Si alloys with rheo-squeeze casting10.4028/www.scientific.net/SSP.285.57 ↗
28. Effect of casting temperature on grain size of Al-Si alloys refined by a novel grain refiner10.4028/www.scientific.net/MSF.794-796.77 ↗
29. Effect of Si, Cu and processing parameters on Al-Si-Cu HPDC castings10.1016/j.jmatprotec.2017.06.043 ↗
30. Optimization of squeeze casting parameters for 2017A aluminum alloy using Taguchi method10.3390/met4020141 ↗
31. Effect of process parameters on distortion and residual stress of high-pressure die-cast AZ91D components10.1007/s40962-017-0186-z ↗
32. Microstructure, mechanical property and thermal conductivity of al–si–fe–mg alloy solidified under high pressures10.1007/s40962-022-00912-8 ↗
33. A review on porosity formation in aluminum-based alloys10.3390/ma16052047 ↗
34. Experimental investigation of mechanical and tribological characteristics of Al 2024 matrix composite reinforced by yttrium oxide particles
35. Characterization and analysis of porosities in high pressure die cast aluminum by using metallography, X-ray radiography, and micro-computed tomography10.3390/ma13143068 ↗
36. Optimization of Porosity Formation in AlSi9Cu3 Alloy in High Pressure Die Casting and Improvement in Break Load
37. Effect of Selected Parameters of Pressure Die Casting on Quality of AlSi9Cu3 Castings10.1515/afe-2015-0044 ↗
38. Computer Aided Engineering (CAE) Simulation for the Design Optimization of Gate System on High Pressure Die Casting (HPDC) Process, Robot10.1016/j.rcim.2018.01.003 ↗
39. Influence of Runner Geometry on the Gas Entrapment in Volume of Pressure Die Cast
40. Influence of Runner Geometry on the Gas Entrapment in Volume of Pressure Die Cast
41. Optimization of the Thin-walled Aluminum Die Casting Die Design by Solidification Simulation
42. Enhanced properties of Ti/Al laminated composite reinforced by high-entropy alloy particles10.3390/met13071227 ↗
43. Investigation of tensile properties and in situ analysis of fracture behavior in high-porosity open-cell nickel foam10.3390/ma17215223 ↗
44. Analysis of the cup-cone fracture in a round tensile bar10.1016/0001-6160(84)90213-X ↗