journal article·2016-01

Achieving Superplasticity in AZ31 Magnesium Alloy Processed by Hot Extrusion and Rolling

Xin Wang, Mengling Wu, Wenliang Ma, Yi Lu, Shuai Yuan

Publisher page

Abstract

Experiments were conducted on ultrafine-grained AZ31 magnesium alloy sheet which was prepared through nano-grained powders processed by hot extrusion at 300 °C plus hot-rolling for four passes at 200. The superplastic behavior had been evaluated in a low-temperature range of 423-523 K and strain rates varied from 5 × 10−4 to 5 × 10−3 s−1. The experiment results showed that tensile testing revealed the superplastic elongations with a maximum measured elongation of 227% when tested at 523 K and strain rate of 5 × 10−4 s−1. The superplastic deformation behavior was attributed to the ultrafine-grained microstructures. The measured elongations mainly depended upon the initial strain rate and temperature, and the strain rate sensitivity m was ~0.5 for this condition. The results indicated that powder metallurgy and subsequent hot extrusion plus rolling were promising approaches to produce the ultrafine-grained magnesium alloy sheet with superplasticity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. B. Zhang, H. Liao, and C. Coddet, Effects of Processing Parameters on Properties of Selective Laser Melting Mg–9% Al Powder Mixture, Mater. Des., 2012, 34, p 753–75810.1016/j.matdes.2011.06.061 ↗
2. D. Sun, C. Chang, and P. Kao, Microstructural Study of Strain Localization in Hot Compressed Mg-3Al-1Zn Alloy, Mater. Sci. Eng., A, 2010, 526, p 7050–705610.1016/j.msea.2010.07.046 ↗
3. Q. Miao, L. Hu, X. Wang, and E. Wang, Grain growth Kinetics of a Fine-Grained AZ31 Magnesium Alloy Produced by Hot Rolling, J. Alloy. Compd., 2010, 493, p 87–9010.1016/j.jallcom.2009.12.049 ↗
4. R. Panicker, A. Chokshi, R. Mishra, R. Verma, and P. Krajewski, Microstructural Evolution and Grain Boundary Sliding in a Superplastic Magnesium AZ31 Alloy, Acta Mater., 2009, 57, p 3683–369310.1016/j.actamat.2009.04.011 ↗
5. T.G. Langdon, The Mechanical Properties of Superplastic Materials, Metall. Mater. Trans. A, 1982, 13, p 689–70110.1007/BF02642383 ↗
6. L.C. Zhang, M. Calin, F. Paturaud, and J. Eckert, Deformation-Induced Grain Refinement in Body-Centered Cubic Co-Fe Alloys Upon Room Temperature compression, Mater. Sci. Eng., A, 2010, 527, p 5796–580010.1016/j.msea.2010.06.009 ↗
7. L. Hu, Y. Wu, Y. Yuan, and H. Wang, Microstructure Nanocrystallization of a Mg-3 wt.% Al-1 wt.% Zn Alloy by Mechanically Assisted Hydriding-Dehydriding, Mater. Lett., 2008, 62, p 2984–298710.1016/j.matlet.2008.01.122 ↗
8. B. Tolaminejad and K. Dehghani, Microstructural Characterization and Mechanical Properties of Nanostructured AA1070 Aluminum After Equal Channel Angular Extrusion, Mater. Des., 2012, 34, p 285–29210.1016/j.matdes.2011.08.003 ↗
9. H. Watanabe, T. Mukai, and K. Higashi, Superplasticity in a ZK60 Magnesium Alloy at Low Temperatures, Scr. Mater., 1999, 40, p 477–48410.1016/S1359-6462(98)00469-2 ↗
10. G. Sakai, Z. Horita, and T.G. Langdon, Grain Refinement and Superplasticity in an Aluminum Alloy Processed by High-Pressure Torsion, Mater. Sci. Eng., A, 2005, 393, p 344–35110.1016/j.msea.2004.11.007 ↗
11. S.H. Kang, Y.S. Lee, and J.H. Lee, Effect of Grain Refinement of Magnesium Alloy AZ31 by Severe Plastic Deformation on Material Characteristics, J. Mater. Process. Technol., 2008, 201, p 436–44010.1016/j.jmatprotec.2007.11.305 ↗
12. A. Yamashita, Z. Horita, and T.G. Langdon, Improving the Mechanical Properties of Magnesium and a Magnesium Alloy Through Severe Plastic Deformation, Mater. Sci. Eng., A, 2001, 300, p 142–14710.1016/S0921-5093(00)01660-9 ↗
13. M. Kai, Z. Horita, and T.G. Langdon, Developing Grain Refinement and Superplasticity in a Magnesium Alloy Processed by High-Pressure Torsion, Mater. Sci. Eng., A, 2008, 488, p 117–12410.1016/j.msea.2007.12.046 ↗
14. M. Mabuchi, T. Asahina, H. Iwasaki, and K. Higashi, Experimental Investigation of Superplastic Behaviour in Magnesium Alloys, Mater. Sci. Technol. Ser., 1997, 13, p 825–83110.1179/mst.1997.13.10.825 ↗
15. K. Kubota, M. Mabuchi, and K. Higashi, Review Processing and Mechanical Properties of Fine-Grained Magnesium Alloys, J. Mater. Sci., 1999, 34, p 2255–226210.1023/A:1004561205627 ↗
16. T. Mukai, H. Watanabe, and K. Higashi, Application of Superplasticity in Commercial Magnesium Alloy for Fabrication of Structural Components, Mater. Sci. Technol., 2000, 16(11), p 1314–131910.1179/026708300101507163 ↗
17. Y.H. Wei, Q.D. Wang, Y.P. Zhu, H.T. Zhou, W.J. Ding, Y. Chino, and M. Mabuchi, Superplasticity and Grain Boundary Sliding in Rolled AZ91 Magnesium Alloy at High Strain Rates, Mater. Sci. Eng., A, 2003, 360, p 107–11510.1016/S0921-5093(03)00407-6 ↗
18. Hidetoshi Somekawa and Toshiji Mukai, Effect of Dominant Diffusion Process on Cavitation Behavior in Superplastic Mg–Al–Zn Alloy, Scr. Mater., 2007, 57, p 1008–101110.1016/j.scriptamat.2007.08.005 ↗
19. M. Mabuchi, K. Ameyama, H. Iwasaki, and K. Higashi, Low Temperature Superplasticity of AZ91 Magnesium Alloy with Non-equilibrium Grain Boundaries, Acta Mater., 1999, 47, p 2047–205710.1016/S1359-6454(99)00094-4 ↗
20. T. McNelley, E. Lee, and M. Mills, Superplasticity in a Thermomechanically Processed High-Mg, Al-Mg Alloy, Metall. Mater. Trans. A, 1986, 17, p 1035–104110.1007/BF02661269 ↗
21. R.Z. Valiev, N. Krasilnikov, and N. Tsenev, Plastic Deformation of Alloys with Submicron-Grained Structure, Mater. Sci. Eng., A, 1991, 137, p 35–4010.1016/0921-5093(91)90316-F ↗