journal article·2017-08

Fatigue Crack Growth Behavior of a New Type of 10% Cr Martensitic Steel Welded Joints with Ni-Based Weld Metal

Qunbing Zhang, Jianxun Zhang

Publisher page

Abstract

In the present work, the fatigue crack growth (FCG) behavior of a new type of 10% Cr martensitic steel welded joints with Ni-based weld metal was comparatively studied for different regions including base metal (BM), heat-affected zone (HAZ) and weld metal (WM). FCG results indicated that the tempered lath martensite BM has a higher fatigue crack growth resistance than the tempered granular martensite HAZ that without a typical lath structure. In comparison, the austenitic WM has the highest fatigue crack growth threshold. Meanwhile, due to the microstructural and chemical compositional differences between BM and WM, a clear interface existed in the welded joints. At the region of the interface, the microstructures were physically connected and an element transition layer was formed. Although the starter notch was positioned at the region of interface, the fatigue crack gradually deviated from the interface and ultimately propagated along the inter-critically heat-affected zone. The difference in microstructure is considered as the primary factor that resulted in the different fatigue crack growth behaviors of the welded joints. In addition, the continuous microstructure connection and composition transition at the interface contributed to the good fatigue resistance at this region.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. S. Prasad, V.B. Rajkumar, and K.C. Hari Kumar, Numerical Simulation of Precipitate Evolution in Ferritic Martensitic Power Plant Steels, Calphad, 2012, 36, p 1–710.1016/j.calphad.2011.10.006 ↗
2. J.A. Francis, W. Mazur, and H.K.D.H. Bhadeshia, Review Type IV Cracking in Ferritic Power Plant Steels, Mater. Sci. Technol., 2006, 22, p 1387–139510.1179/174328406X148778 ↗
3. R. Agamennone, W. Blum, C. Gupta, and J.K. Chakravartty, Evolution of Microstructure and Deformation Resistance in Creep of Tempered Martensitic 9–12%Cr–2%W–5%Co Steels, Acta Mater., 2006, 54, p 3003–301410.1016/j.actamat.2006.02.038 ↗
4. N. Dudova, A. Plotnikova, D. Molodov, A. Belyakov, and R. Kaibyshev, Structural Changes of Tempered Martensitic 9%Cr–2%W–3%Co Steel During Creep at 650 °C, Mater. Sci. Eng. A, 2012, 534, p 632–63910.1016/j.msea.2011.12.020 ↗
5. F. Yin, L. Tian, B. Xue, X. Jiang, and L. Zhou, Effect of Titanium on Second Phase Precipitation Behavior in 9–12Cr Ferritic/Martensitic Heat Resistant Steels, Rare Met., 2011, 30, p 497–50010.1007/s12598-011-0332-3 ↗
6. M.C. Brandes, L. Kovarik, M.K. Miller, G.S. Daehn, and M.J. Mills, Creep Behavior and Deformation Mechanisms in a Nanocluster Strengthened Ferritic Steel, Acta Mater., 2012, 60, p 1827–183910.1016/j.actamat.2011.11.057 ↗
7. L. Helis, Y. Toda, T. Hara, H. Miyazaki, and F. Abe, Effect of Cobalt on the Microstructure of Tempered Martensitic 9Cr Steel for Ultra-Supercritical Power Plants, Mater. Sci. Eng. A, 2009, 510–511, p 88–9410.1016/j.msea.2008.04.131 ↗
8. Q. Zhang, J. Zhang, P. Zhao, Y. Huang, Y. Yang, and Y. Zhao, Microstructure of 10% Cr Martensitic Heat-Resistant Steel Welded Joints and Type IV Cracking Behavior During Creep Rupture at 650 °C, Mater. Sci. Eng. A, 2015, 638, p 30–3710.1016/j.msea.2015.04.062 ↗
9. D.W. Rathod, S. Pandey, P.K. Singh, and R. Prasad, Experimental Analysis of Dissimilar Metal Weld Joint: Ferritic to Austenitic Stainless Steel, Mater. Sci. Eng. A, 2015, 639, p 259–26810.1016/j.msea.2015.05.011 ↗
10. F. Khodabakhshi, M. Kazeminezhad, and A.H. Kokabi, Metallurgical Characteristics and Failure Mode Transition for Dissimilar Resistance Spot Welds Between Ultra-Fine Grained and Coarse-Grained Low Carbon Steel Sheets, Mater. Sci. Eng. A, 2015, 637, p 12–2210.1016/j.msea.2015.04.019 ↗
11. M. Sarkari Khorrami, M.A. Mostafaei, H. Pouraliakbar, and A.H. Kokabi, Study on Microstructure and Mechanical Characteristics of Low-Carbon Steel and Ferritic Stainless Steel Joints, Mater. Sci. Eng. A, 2014, 608, p 35–4510.1016/j.msea.2014.04.065 ↗
12. J. Parker, Factors Affecting Type IV Creep Damage in Grade 91 Steel Welds, Mater. Sci. Eng. A, 2013, 578, p 430–43710.1016/j.msea.2013.04.045 ↗
13. T.C. Totemeier, J.A. Simpson, and H. Tian, Effect of Weld Intercooling Temperature on the Structure and Impact Strength Of Ferritic–Martensitic Steels, Mater. Sci. Eng. A, 2006, 426, p 323–33110.1016/j.msea.2006.04.023 ↗
14. T. Sakthivel, M. Vasudevan, K. Laha, P. Parameswaran, K.S. Chandravathi, S. Panneer Selvi, V. Maduraimuthu, and M.D. Mathew, Creep Rupture Behavior of 9Cr–1.8 W–0.5Mo–VNb (ASME grade 92) Ferritic Steel Weld Joint, Mater. Sci. Eng. A, 2014, 591, p 111–12010.1016/j.msea.2013.10.071 ↗
15. L. Falat, M. Svoboda, A. Výrostková, I. Petryshynets, and M. Sopko, Microstructure and Creep Characteristics of Dissimilar T91/TP316H Martensitic/Austenitic Welded Joint with Ni-Based Weld Metal, Mater. Charact., 2012, 72, p 15–2310.1016/j.matchar.2012.06.014 ↗
16. M. Pouranvari, On the Weldability of Grey Cast Iron Using Nickel Based Filler Metal, Mater. Des., 2010, 31, p 3253–325810.1016/j.matdes.2010.02.034 ↗
17. M. Velu and S. Bhat, Experimental Investigations of Fracture and Fatigue Crack Growth of Copper–Steel Joints Arc Welded Using Nickel-Base Filler, Mater. Des., 2015, 67, p 244–26010.1016/j.matdes.2014.11.026 ↗
18. H. Lee, S. Lee, J. Kim, and J. Lee, Creep–fatigue Damage for a Structure with Dissimilar Metal Welds of Modified 9Cr–1Mo Steel and 316L Stainless Steel, Int. J. Fatigue, 2007, 29, p 1868–187910.1016/j.ijfatigue.2007.02.009 ↗
19. S.B. Narasimhachary and A. Saxena, Crack Growth Behavior of 9Cr − 1Mo (P91) Steel Under Creep–Fatigue Conditions, Int. J. Fatigue, 2013, 56, p 106–11310.1016/j.ijfatigue.2013.07.006 ↗
20. V. Chaswal, G. Sasikala, S.K. Ray, S.L. Mannan, and B. Raj, Fatigue Crack Growth Mechanism in Aged 9Cr–1Mo Steel: Threshold And Paris Regimes, Mater. Sci. Eng. A, 2005, 395, p 251–26410.1016/j.msea.2004.12.026 ↗
21. B.M. Schönbauer, S.E. Stanzl-Tschegg, A. Perlega, R.N. Salzman, N.F. Rieger, S. Zhou, A. Turnbull, and D. Gandy, Fatigue Life Estimation of Pitted 12% Cr Steam Turbine Blade Steel in Different Environments and at Different Stress Ratios, Int. J. Fatigue, 2014, 65, p 33–4310.1016/j.ijfatigue.2013.10.003 ↗
22. T. Wakai, O. Inoue, M. Ando, and S. Kobayashi, Thermal Fatigue Crack Growth Tests and Analyses of Thick Wall Cylinder Made of Mod. 9Cr–1Mo Steel, Nucl. Eng. Des., 2015, 295, p 797–80310.1016/j.nucengdes.2015.07.034 ↗
23. M. Nani Babu, G. Sasikala, B. Shashank Dutt, S. Venugopal, S.K. Albert, A.K. Bhaduri, and T. Jayakumar, Investigation on Influence of Dynamic Strain Ageing on Fatigue Crack Growth Behaviour of Modified 9Cr–1Mo Steel, Int. J. Fatigue, 2012, 43, p 242–24510.1016/j.ijfatigue.2012.02.022 ↗
24. Y. Kumar, S. Venugopal, G. Sasikala, S.K. Albert, and A.K. Bhaduri, Study of Creep Crack Growth in a Modified 9Cr–1Mo Steel Weld Metal and Heat Affected Zone, Mater. Sci. Eng. A, 2016, 655, p 300–30910.1016/j.msea.2015.12.053 ↗
25. X. Deng, F. Lu, H. Cui, X. Tang, and Z. Li, Microstructure Correlation and Fatigue Crack Growth Behavior in Dissimilar 9Cr/CrMoV Welded Joint, Mater. Sci. Eng. A, 2016, 651, p 1018–103010.1016/j.msea.2015.11.081 ↗
26. Q. Wu, F. Lu, H. Cui, X. Liu, P. Wang, and X. Tang, Role of Butter Layer in Low-Cycle Fatigue Behavior of Modified 9Cr and CrMoV Dissimilar Rotor Welded Joint, Mater. Des., 2014, 59, p 165–17510.1016/j.matdes.2014.02.022 ↗
27. M.-L. Zhu, F.-Z. Xuan, and S.-T. Tu, Interpreting Load Ratio Dependence of Near-Threshold Fatigue Crack Growth by a New Crack Closure Model, Int. J. Press. Vessels Pip., 2013, 110, p 9–1310.1016/j.ijpvp.2013.04.015 ↗
28. A. Trudel, M. Sabourin, M. Lévesque, and M. Brochu, Fatigue Crack Growth in the Heat Affected Zone of a Hydraulic Turbine Runner Weld, Int. J. Fatigue, 2014, 66, p 39–4610.1016/j.ijfatigue.2014.03.006 ↗