journal article·2021-06

Experimental and Numerical Investigations of Wear Resistance Characteristics of XCr13 during Advanced High-Strength Steel Stamping

Changsheng Wang, Jun Chen

Publisher page

Abstract

Owing to the high strength and hardness of advanced high-strength steels (AHSS), the die materials for AHSS sheet stamping must have superior mechanical properties. A novel carburization technology on high-chromium, low-carbon, low-cost stainless steel XCr13 was used to achieve a hardness of approximately 60 HRC, with a carburized layer of approximately 0.5 mm; these specifications meet the requirements of AHSS sheet stamping. To evaluate the wear characteristics of the treated XCr13, regular pin-on-disk wear tests were performed under dry sliding conditions at room temperature. JIS SKD11, a popular cold work die material, was also tested and compared with XCr13. A numerical simulation model for AHSS sheet flanging with a W-shaped specimen was set up in ABAQUS, and the user subroutine UMESHMOTION was used to evaluate the wear resistance of the two die materials, including the wear surface profile, wear depth, and wear severity index value. For JIS SKD11, the agreement between the simulation and experiment results was good, which verifies the reliability and accuracy of the proposed wear simulation model and method. It was found that the wear resistance of carburized XCr13 was at the same level as that of JIS SKD11 because of the carburized zone. Further, carburized XCr13 can work well as a die material for AHSS stamping.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Metal Forming Simulation Techniques · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. O. Cora and M. Koç, Experimental Investigations on Wear Resistance Characteristics of Alternative Die Materials for Stamping of Advanced High Strength Steels (AHSS), Int. J. Machine Tools Manuf., 2009, 49, p 897–905.10.1016/j.ijmachtools.2009.07.003 ↗
2. O. Sandberg, M. Fallstrom and T. Johansson, Characterization of Tool Wear in Stamping of EHS and UHS Steel Sheets, In: Proceedings of the International Conference on Recent Advances in Manufacture and Use of Tools and Dies and Stamping of Steel Sheets, Olofstroem Sweden, 2004, p 151-169
3. L.Z. Han and J.S. Pan, Behavior of Austenite Grain Growth in X12CrMoWVNb10-1-1 Ferrite Heat-resistant Steel, Acta Metall., 2009, 45, p 1146–1150.
4. L.Z. Han and J.S. Pan, Martensitic Transformation in X12CrMoWVNbN10-1-1 Ferrite Heat-Resistant Steel, J Shanghai Jiao Tong University, 2010, 44, p 11–15.
5. P.C. Chakraborti and M.K. Mitra, Microstructure and Tensile Properties of High Strength Duplex Ferrite–martensite (DFM) Steels, Mater. Sci. Eng., 2007, 466, p 123–133.10.1016/j.msea.2007.02.042 ↗
6. Y.C. Lin, S.W. Wang and T.M. Chen, A Study on The Wear Behavior of Hardened Medium Carbon Steel, J. Mater. Process. Technol., 2002, 120, p 126–132.10.1016/S0924-0136(01)01195-5 ↗
7. Ö.N. Cora and K. Namiki, Wear Performance Assessment of Alternative Stamping Die Materials Utilizing a Novel Test System, Wear, 2009, 267, p 1123–1129.10.1016/j.wear.2008.12.111 ↗
8. J. Krawczyk, E. Rożniata and J. Pacyna, The Influence of Hypereutectoid Cementite Morphology upon Fracture Toughness of Chromium–nickel–molibdenium Cast Steel of Ledeburite Class, J. Mater. Process. Technol., 2005, 162, p 336–341.10.1016/j.jmatprotec.2005.02.097 ↗
9. M. Pellizzari and D. Cescato, Hot Friction and Wear Behavior of High Speed Steel and High Chromium Iron for Rolls, Wear, 2009, 267, p 467–475.10.1016/j.wear.2009.01.049 ↗
10. Z.L. Lu, Q.C. Rao and Z.H. Jin, An Investigation of The Corrosion–abrasion Wear Behavior of 6% Chromium Martensitic Cast Steel, J. Mater. Process. Technol., 1999, 95, p 180–184.10.1016/S0924-0136(99)00289-7 ↗
11. H.T. Lee, W.P. Rehbach, F.C. Hsu and T.Y. Tai, The Study of EDM Hole-drilling Method for Measuring Residual Stress in SKD11 Tool Steel, J. Mater. Process. Technol., 2004, 149, p 88–93.10.1016/j.jmatprotec.2003.10.056 ↗
12. J.L. Li, L.L. Jing and M. Chen, An FEM Study on Residual Stresses Induced by High-speed End-milling of Hardened Steel SKD11, J. Mater. Process. Technol., 2009, 209, p 4515–4520.10.1016/j.jmatprotec.2008.10.042 ↗
13. T. Sasaki, T. Yakou, M. Umemoto and Y. Todaka, Two-body Abrasive Wear Property of Cementite, Wear, 2006, 260, p 1090–1095.10.1016/j.wear.2005.07.010 ↗
14. E.S. Zanoria, Application of the Ring-on-ring Test for Abrasive Wear Modeling of Rolling Undercarriage Components in Track-type Machines, Wear, 2004, 257, p 205–214.10.1016/j.wear.2003.12.003 ↗
15. W. Chen, Y.M. Gao, Y. Wang and H.Q. Li, Tribological Behavior of Si3N4-hBN Ceramic Materials without Lubrication under Different Test Modes, Tribol. Trans., 2010, 53, p 787–798.10.1080/10402004.2010.486522 ↗
16. M.X. Wei, S.Q. Wang and L. Wang, Wear and Friction Characteristics of a Selected Stainless Steel, Tribol. Trans., 2011, 54, p 840–848.10.1080/10402004.2011.606960 ↗
17. L.J. Yang, An Integrated Transient and Steady-State Adhesive Wear Model, Tribol. Trans., 2003, 46, p 369–375.10.1080/10402000308982639 ↗
18. S.P. Chen and J.F. Dang, A Variable Spread Fuzzy Linear Regression Model with Higher Explanatory Power and Forecasting Accuracy, Inf. Sci., 2008, 178, p 3973–3988.10.1016/j.ins.2008.06.005 ↗
19. S. Basavarajappa and G. Chandramohan, Dry Sliding Wear Behavior of Metal Matrix Composites: A Statistical Approach, J. Mater. Eng. Perform., 2006, 15, p 656–660.10.1361/105994906X150731 ↗
20. E. Oberg, F. Jones and H. Ryffel, Machinery's Handbook, Industrial Press Inc., 28th Edition, New York, US, 2008
21. S.M. Xia and Z.M. Zhang, Research on Improvement for Heat Treatment Process of Connecting Rod and Pin Made of 3Cr13 Steel, Hot Working Technology, 2000, 29, p 39–40.
22. L. Kurt, Handbook of Metal Forming, New York, McGraw-Hill, 1985, 26th Ed.
23. S. Kalpakjian and S.R. Schmid, Manufacturing Processes for Engineering Materials, Addison-Wesley, 1991, 2nd Ed.
24. K. Ersoy-Nurnberg, G. Nurnberg and H. Hoffmann, Simulation of Wear on Sheet Metal Forming Tools – an Energy Approach, Wear, 2008, 265, p 1801–1807.10.1016/j.wear.2008.04.039 ↗
25. R. Hambli, D. Soulat and A. Chamekh, Finite Element Prediction of Blanking Tool Cost Caused by Wear, Int J. Adv. Manuf. Technol., 2009, 44, p 648–656.10.1007/s00170-008-1859-9 ↗
26. R. Hambli, F. Guerin and B. Dumon, Numerical Evaluation of the Tool Wear Influence on Metal-Punching Processes, Int J. Adv. Manuf. Technol., 2003, 21, p 483–493.10.1007/s001700300057 ↗
27. J. Wen, Y. Yang and M. Jeng, Optimization of Die Casting Conditions for Wear Properties of Alloy AZ91D Components Using the Taguchi Method and Design of Experiments Analysis, Int J. Adv. Manuf. Technol., 2009, 41, p 430–439.10.1007/s00170-008-1499-0 ↗
28. P. Palanisamy, I. Rajendran and S. Shanmugasundaram, Prediction of Tool Wear Using Regression and ANN Models in End-milling Operation, Int J. Adv. Manuf. Technol., 2008, 37, p 29–41.10.1007/s00170-007-0948-5 ↗
29. J. Archard, Contact and Rubbing of Flat Surfaces, J Appl. Phys., 1953, 24, p 981–988.10.1063/1.1721448 ↗
30. J. Archard, The Wear of Materials under Unlubricated Conditions, Proc. Royal Soc., 1958, 23, p 71–73.
31. C.S. Wang, J. Chen and Z.C. Xia, Die Wear Prediction by Defining Three-stage Coefficient K for AHSS Sheet Metal Forming Process, The International Journal of Advanced Manufacturing Technology, 2013, 69, p 797–803.10.1007/s00170-013-5069-8 ↗
32. B.C. Wen, Standard Handbook of Machine design, China machine press, 5th ed., Beijing, 2010
33. Hibbtt, Karlsson & Sorensen.Inc., ABAQUS Analysis User’s Manual 6.14, 2016, Version 6.14
34. Z.C. Xia and F. Ren, Die wear severity Diagram and simulation, SAE International, 2007, p 2007-1-169410.4271/2007-01-1694 ↗