Green composite plaster with modified morphology for enhanced thermal comfort in buildings
Source abstract
Abstract
Partially replacement of constituent materials in cementitious products using waste materials leads to reduce the CO2 emissions while saving the natural resources and minimize the environmental hazards caused by waste disposal. Development of such an alternative for conventional plaster with better thermal performance, strength and durability characteristics will result in energy savings in the construction and operational phases of buildings. A composite plaster was developed by dry mixing of fine aggregate, bottom ash (BA), Portland cement and poly-carboxylic ether-based admixture. Their phase composition and microstructure morphologies were evaluated using XRD and SEM for a range of compositions and comparisons were made by varying water to cement ratios on the development of the best composition. The results indicate that the morphology and grain dimensions of the developed composite plaster can save 60 % of fine aggregate with effective replacement of bottom ash while maintaining the water to cement ratio of 1.15. A reduction of thermal conductivity by 76 % was noted concerning to the conventional plaster. The application of this waste based composite plaster in model units indicated good adhesion properties with better surface texture and good water resistance characteristics. No thermal or shrinkage cracks appeared in the operational phase of the models under outdoor exposure of two years to the tropical environment. A numerical model was also developed to predict the indoor wall temperature variation of a compartment finished with the said composite plaster and a comparison was made with the measured temperature cycle during outdoor exposure. A parametric study was conducted to compare the heat balance of the developed models with available systems and different climate variations.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Hygrothermal properties of building materials · Building Energy and Comfort Optimization · Building materials and conservation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. The cost benefit analysis and potential emission reduction evaluation of applying wall insulation for buildings in Malaysia10.1016/j.rser.2012.04.045 ↗
2. Evans · 2020
3. Review on Current Research Status on Bottom Ash: An Indian Prospective10.1007/s40030-014-0100-0 ↗
4. Fly ash
5. Properties of sustainable concrete containing fly ash, slag and recycled concrete aggregate10.1016/j.conbuildmat.2009.02.011 ↗
6. Use of bottom ash from coal fired thermal power plants in production of cellular lightweight concrete10.1109/MERCon.2018.8421957 ↗
7. Production of thermal insulation blocks from bottom ash of fluidized bed combustion system10.1177/0734242X17707575 ↗
8. Effect of bottom ash as replacement of fine aggregates in concrete
9. Compressive strength, flexural strength and thermal conductivity of autoclaved concrete block made using bottom ash as cement replacement materials10.1016/j.matdes.2011.08.046 ↗
10. Effect of insulation on the bond behaviour of CFRP-Plated concrete elements
11. Utilization of coal bottom ash to improve thermal insulation of construction material10.1007/s10163-015-0419-2 ↗
12. Thermal and microstructure properties of cement mortar containing ceramic waste powder as alternative cementitious materials10.1016/j.conbuildmat.2019.07.029 ↗
13. Traditional, state-of-the-art and renewable thermal building insulation materials: an overview10.1016/j.conbuildmat.2019.04.102 ↗
14. Thermal and environmental impact analysis of rice husk ash-based mortar as insulating wall plaster10.1016/j.conbuildmat.2021.122744 ↗
15. Development of sustainable mortar using waste rice husk ash from rice mill plant: physical and thermal properties10.1016/j.jobe.2021.102614 ↗
16. Structural feasibility of Expanded Polystyrene (EPS) based lightweight concrete sandwich wall panels10.1016/j.conbuildmat.2017.02.027 ↗
17. Application of expanded polystyrene (EPS) in buildings and constructions: a review10.1002/app.47529 ↗
18. Optimization of microstructure of basalt-based fibers intended for improved thermal and acoustic insulations
19. Energy savings potential of chilled-ceiling combined with desiccant cooling in hot and humid climates10.1016/S0378-7788(01)00132-3 ↗
20. A comprehensive review on the properties of coal bottom ash in concrete as sound absorption material10.1051/matecconf/201710301005 ↗
21. Pozzolanic properties of pulverized coal combustion bottom ash10.1016/S0008-8846(99)00098-8 ↗
22. Microstructure and thermal conductivity of cement-based foam: a review10.1016/j.jobe.2018.09.008 ↗
23. Investigations of physicochemical properties of bottom-ash materials for use them as secondary raw materials
24. Reuse of fly ash and bottom ash in mortars with improved thermal conductivity performance for buildings10.1016/j.heliyon.2018.e00934 ↗
25. Performance on coal bottom ash in hot mix asphalt
26. Thermal conductivity: VII, Analysis of variation of conductivity with termperature for Al2O3, BeO, and MgO
27. ASTM International · 2019
28. ASTM International · 2018
29. ASTM International · 2020
30. ASTM International · 2007
31. Standard test method for flow of hydraulic cement mortar
32. 2013
33. Effects of wall orientation and thermal insulation on time lag and decrement factor
34. Investigation of building walls exposed to periodic heat transfer conditions for green and energy efficient building construction10.1016/j.protcy.2016.03.055 ↗
35. Investigation on an effective bond arrangement of insulated CFRP-strengthened flexural members for improved thermo-mechanical performance
36. Weather Today, (n.d.). https://www.timeanddate.com/weather. (Accessed 30 August 2020).
37. Optimum location and distribution of insulation layers on building walls with various orientations10.1016/j.buildenv.2006.07.025 ↗