journal article·2024-07Open access

Comprehensive consideration of user-control variables for drilling resistance measurement system and estimation of uniaxial compressive strength of sandstone and clay brick

Qiong Zhang, Zhongjian Zhang, Feiyue Wang, Zhongqi Yue

Abstract

The Drilling Resistance Measurement System (DRMS) test is a minimally destructive technique suitable for the field assessment of the mechanical properties (such as uniaxial compressive strength) of masonry relic surfaces within a certain depth range, but the test results of drilling resistance are prone to be affected by user-control variables. Currently, there is no unified test specification or standard for the manual of user-control variables. To ensure that the drilling resistance test results are comparable under different user-control variables, in this study, sandstone and clay brick were used as the research objects to investigate and analyse the effects of different user-control variables on the drilling resistance test results. The results show that the drilling resistance had a linear positive correlation with the penetration rate, drill bit diameter, and drill bit wear but a linear negative correlation with the revolution speed; the drilling resistance of sandstone had a linear negative correlation with the water content, while the opposite was observed for clay bricks. The drilling resistance mean values at different drilling depth ranges were compared, and a method for calculating the drilling resistance mean value was proposed. Moreover, the uniaxial compressive strengths of the sandstone and clay brick were evaluated by drilling resistance. Wider spreading of the DRMS can be achieved by recording user-control variables in detail if the correlation expressed in this paper is further tested. • Correlations between user-control variables and drilling resistance were established. • Water content has different effects on the drilling resistance of sandstone and clay brick. • UCS shows a better correlation with drilling resistance than Leeb hardness for clay brick. • Detailed recording of user-control variables contributes to the comparability of data.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Tunneling and Rock Mechanics · Drilling and Well Engineering · Building materials and conservation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Mimoso · A N. DRMS Tech. Lab. Int. Conf. "Non Destr. Investig. Micron Diagn. Conserv. Cult. Environ. Herit. · 2005 · 8 · 1
2. Drilling resistance: overview and outlook
3. Dagrain, F., Descamps, T., Poot, B., 2010. Less-destructive testing of masonry materials: a comparison between scratching and drilling approaches. 8th international masonry conference, Dresden, Germany.
4. Prediction of Compressive Strength for Heterogeneous Mortars from Drilling Resistance Data10.1080/15583058.2018.1547800 ↗
5. On the estimation of marbles weathering by thermal action using drilling resistance
6. Stone consolidation by biomineralisation. Contribution for a new conceptual and practical approach to consolidate soft decayed limestones10.1016/j.culher.2019.04.022 ↗
7. Consolidation of carbonate stones: influence of treatment procedures on the strengthening action of consolidants10.1016/j.culher.2011.07.003 ↗
8. Improving uniaxial compressive strength estimation of carbonate sedimentary rocks by combining minimally invasive and non-destructive techniques
9. In situ mechanical characterization of the mortar in masonry buildings with DRMS
10. Prediction of compression strength of ancient mortars through in situ drilling resistance technique
11. Micro-destructive cutting techniques for the characterization of natural limestone10.1016/j.ijrmms.2015.02.012 ↗
12. Evaluation of the Compressive Strength of Ancient Clay Bricks Using Microdrilling10.1061/(ASCE)0899-1561(2007)19:9(791) ↗
13. Optimization of drilling resistance measurement (DRM) user-controlled variables10.1617/s11527-017-1113-8 ↗
14. The conservation of monuments: A new method to evaluate consolidating treatments. Int. J
15. Validation of a Model of Rotary Drilling of Rocks with the Drilling Force Measurement System. Int. J
16. Measurement and analysis of thrust force and delamination in drilling glass fiber reinforced polypropylene composites using different drills10.1016/j.measurement.2019.106973 ↗
17. Modeling of small-diameter rotary drilling tests on marbles10.1016/j.ijrmms.2006.03.008 ↗
18. A New Method for Data Correction in Drill Resistance Tests for the Effect of Drill Bit Wear. Int. J
19. An alternative method for correction of data for the effect of drill bit wearing in drilling tests dealing with heterogeneous material
20. Wear mechanisms and tool life management of WC–Co drills during dry high speed drilling of woven carbon fibre composites10.1016/j.wear.2009.01.031 ↗
21. Wear mechanisms of micro-drills during dry high speed drilling of PCB10.1016/j.jmatprotec.2012.05.004 ↗
22. The role of aggregate and binder content in the physical and mechanical properties of mortars from historical rubble stone masonry walls of the National Palace of Sintra
23. A new portable system for determining the state of conservation of monumental stones10.1617/s11527-005-9013-8 ↗
24. Effect of water saturation and loading rate on the mechanical properties of Red and Buff Sandstones10.1016/j.ijrmms.2016.07.005 ↗
25. Influence of moisture content on the mechanical properties of an ancient high-porosity building sandstone: San Cristóbal's stone (Andalusia, Spain)
26. A new interpretation methodology for microdrilling data from soft mortars10.1016/j.culher.2016.06.010 ↗
27. Evaluation of the Compressive Strength of Ancient Clay Bricks Using Microdrilling10.1061/(ASCE)0899-1561(2007)19:9(791) ↗
28. Characterisation of Mortars Using Drilling Resistance Measurement System (DRMS): Tests on Field Panels Samples10.1007/978-94-007-4635-0_32 ↗
29. Cox · 1974
30. A Phenomenological Model for the Action of Drag Bits10.1016/0148-9062(92)91041-3 ↗
31. Fracture mechanisms induced in a brittle material by a hard cutting indenter10.1016/S0020-7683(01)00117-2 ↗
32. Pfefferkorn, S., 2000. Correction functions for eliminating drill bit abrasion and blocked drill dust transport. In: Tiano P, editor. Proceedings DRILLMORE, Firenze, Italy, pp. 67-74.
33. Surface damage on cemented carbide rock-drill buttons10.1016/S0043-1648(01)00553-1 ↗
34. Nogueira, R., Pinto, A.P.F., Gomes, A., 2014. The drilling resistance test in the characterization of lime mortar renders in multilayer system. 9th International Masonry Conference, Guimarães.
35. High-resolution micro-CT with 3D image analysis for porosity characterization of historic bricks10.1186/s40494-022-00723-4 ↗
36. The effects of water on the strength of black sandstone in a brittle regime10.1016/j.enggeo.2018.03.025 ↗
37. Effect of water on sandstone's fracture toughness and frictional parameters: Brittle strength constraints
38. A thermodynamic-based model for modeling thermo-elastoplastic behaviors of saturated clayey soils considering bound water dehydration10.1016/j.jrmge.2022.09.008 ↗
39. Analysis of Coupled Axial-Torsional Drill-String Vibration Based on Fuzzy Bit-Rock Interaction Model Considering Bit Balling Condition10.1109/TII.2022.3233664 ↗
40. Assessing the reliability of non-destructive and moderately invasive techniques for the evaluation of uniaxial compressive strength of stone masonry units10.1016/j.conbuildmat.2016.07.130 ↗
41. Non-destructive strength estimation of vintage clay bricks based on rebound hardness in architectural heritage buildings
42. Impact of salt and frost weathering on the physical and durability properties of travertines and carbonate tufas used as building material10.1007/s12665-018-7339-0 ↗