journal article·2022-06Open access

An investigative study for the prediction of compressive strength of cement-clay interlocking (CCI) hollow brick masonry walls

Panuwat Joyklad, Nazam Ali, Ekkachai Yooprasertchai, Syed Taseer Abbas Jaffar, Hassan M. Magbool, Qudeer Hussain, Krisada Chaiyasarn

Abstract

Masonry structures are used in many parts of the world because of their varying benefits of being low-cost, heat insulations, local availability, and skilled labor. Therefore, to investigate the compressive stress-strain behavior and detailed analysis and assessment of masonry structures made of CCI bricks is imperative. Axial compressive results of 10 hollow cement-clay interlocking (CCI) bricks made masonry walls are presented. 10 masonry walls were tested under concentric compressive load in 2 groups. Bricks of each group had different compressive strength. Five walls in each group comprised of 1 control wall (ungrouted), 1 wall grouted with Ordinary Portland Cement (OPC), 1 wall grouted with non-shrink (NS) cement, 1 wall grouted with OPC and strengthened by steel bars, and 1 wall grouted with NS and strengthened with steel bars. Among 5 walls in each group, control wall created the lower bound in terms of the peak load sustained. While the upper bound was created by the wall grouted with NS cement and further strengthened by steel bars. It was found that the addition of grout (irrespective of its type) significantly improved the peak compressive load. However, increase in peak load over that of the control wall was associated to the grout type. Walls grouted with NS cement attained higher peak loads as compared to those grouted with OPC. It was observed that the addition of cement grout does not guarantee a ductile post-peak behavior. Addition of steel bars not only increased the peak loads, but it also improved the post peak behavior. Accuracy of existing compressive load analytical models was assessed, and it was found that none of the analytical models considered were able to predict close approximations. A linearly regressed model is proposed to predict compressive strength of CCI brick masonry walls with good accuracy.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Masonry and Concrete Structural Analysis · Hygrothermal properties of building materials · Building materials and conservation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Stress-strain characteristics of clay brick masonry under uniaxial compression10.1061/(ASCE)0899-1561(2007)19:9(728) ↗
2. A review: durability of fired clay brick masonry wall due to salt attack
3. Experimental seismic performance assessment of asymmetric masonry buildings10.1016/j.engstruct.2017.10.059 ↗
4. Homogenization strategy for brick masonry walls under in-plane loading10.1016/j.conbuildmat.2017.12.133 ↗
5. Thermal, hydric and mechanical behaviours of adobes stabilized with cement10.1016/j.conbuildmat.2017.10.001 ↗
6. Compression and sonic tests to assess effectiveness of grout injection on three-leaf stone masonry walls10.1080/15583058.2013.826300 ↗
7. Behaviour and strength assessment of masonry prisms
8. Compressive behavior of unconfined and confined clay brick masonry10.1061/(ASCE)0733-9445(2004)130:4(650) ↗
9. Brick-mortar bond and masonry compressive strength10.1061/(ASCE)0899-1561(2005)17:2(229) ↗
10. Mechanics of masonry in compression10.1061/(ASCE)0733-9445(1985)111:4(857) ↗
11. Bond strength and compressive stress-strain characteristics of brick masonry10.1016/j.jobe.2016.11.006 ↗
12. Experimental investigation of compressive failure in masonry brick assemblages made with soft brick
13. Strength and stress–strain characteristics of traditional adobe block and masonry10.1617/s11527-012-9987-y ↗
14. T. Kaaki, Behavior and Strength of Masonry Prisms Loaded in Compression (MSc Thesis), 2013.
15. S. Joseph, B. Mcgarry, B. Sajjakulnukit, O. Sopchokchai, A Study of Brick Production in Thailand* (Issues on Women, Energy, and the Environment), 1990.
16. Mechanical properties of local cement-clay interlocking bricks in central part of Thailand
17. Axial compressive response of grouted cement–clay interlocking hollow brick walls10.1007/s42107-019-00140-2 ↗
18. ASTM International ASTM C1314 – 21 Standard Test Method for Compressive Strength of Masonry Prisms, 2021.
19. ASTM International ASTM C109/C109M – 20 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens), 2020.
20. ASTM International ASTM E8/E8M – 16a Standard Test Methods for Tension Testing of Metallic Materials, 2016.
21. Soft computing-based models for the prediction of masonry compressive strength10.1016/j.engstruct.2021.113276 ↗
22. W. Mann, Statistical evaluation of tests on masonry by potential functions, in: Proceedings of the Sixth International Brick Masonry Conference, Rome, Italy, 1982, pp. 86–98.
23. Dayaratnam Pasala Brick and Reinforced Brick Structures, Oxford and IBH, Delhi, India, 1987.
24. Allowing for uncertainties in the modelling of masonry compressive strength10.1016/S0950-0618(02)00108-3 ↗
25. Uniaxial compressive strength and stiffness of field-extracted and laboratory-constructed masonry prisms10.1061/(ASCE)MT.1943-5533.0000731 ↗
26. O. Bröcker, Die Auswertung von Tragfähigkeitsversuchen an Gemauerten Wänden, in: Proceedings of the Betonstein-Zeitung, 1963, pp. 19–21.
27. Characteristic compressive strength of brickwork walls from collected test results
28. Compressive properties of structural clay tile prisms10.1061/(ASCE)0733-9445(1997)123:7(920) ↗
29. Strength and elasticity of brick masonry prisms and wallettes under compression10.1617/s11527-006-9141-9 ↗
30. Experimental study on axial compressive strength and elastic modulus of the clay and fly ash brick masonry
31. Compressive strength of masonry made of clay bricks and cement mortar: estimation based on neural networks and fuzzy logic10.1016/j.engstruct.2012.09.029 ↗
32. An experimental investigation of mechanical properties in clay brick masonry by partial replacement of fine aggregate with clay brick waste
33. S.R. Sarhat, E.G. Sherwood, The prediction of compressive strength of grouted hollow concrete block masonry based on the contributions of its individual components, in: Proceedings of the 12th Canadian Masonry Symposium. 2012.