A comparative study of mechanical and environmental properties of concrete using jujube nucleus as a coarse aggregate
Source abstract
Abstract
The ever-increasing generation of aggregates in the construction industry has caused a serious burden on the environmental protection of mountains and ecosystems. The shortage of natural coarse aggregate provides an impetus for the utilization of agricultural waste. Aiming to provide a cleaner option for the production of agricultural waste concrete originating from agricultural by-products jujube nucleus, the viability of using jujube nucleus as a substitute for coarse aggregate in the preparation of agricultural waste concrete is experimentally investigated in this study. The workability, weight loss, mechanical and environmental properties of jujube nucleus concrete (JNC) were evaluated with the variation of five different jujube nucleus (JN) replacement ratios (i.e., 0 %, 25 %, 50 %, 75 %, and 100 %), and five different temperatures (i.e. 20 °C, 200 °C, 400 °C, 600 °C, and 800 °C). The results show that as the JN replacement ratio increases, the slump values of JNC decreased gradually whilst the weight loss of JNC is more obvious than that of ordinary concrete with the increase in the elevated temperature, which is probably due to the growing amount of ettringite having chemical-bound water caused by sucrose molecules. In addition, the increase in the JN replacement ratio would decrease the compressive strength of JNC as compared to ordinary concrete, with a minimum and maximum reduction of about 26 % (25 %) and 97 % (100 %) respectively. As the elevated temperature increases, the compressive strength of JNC with 25 % JN replacement ratio also decreases, with a minimum and maximum reduction of approximately 28 % (100 °C) and 37 % (400 °C) respectively. A series of calculation formulas are established to predict the compressive performance of JNC by considering the JN replacement ratio and the elevated temperature. The cost and EI assessment indicate that the utilization of jujube nucleus in concrete material could reduce the consumption of non-renewable resources and ozone depletion to a certain extent. On a whole, the JNC with the 25 % JN replacement ratio may be the appropriate solution for the usage of jujube nucleus in agricultural waste concrete production. This paper provides a theoretical basis for the application of jujube nucleus in concrete materials, paving a way to exploit the JNC products as an alternative solution for a sustainable built environment.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Concrete and Cement Materials Research · Microbial Applications in Construction Materials · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (68)
Show source-provided references
1. The greening of the concrete industry10.1016/j.cemconcomp.2008.12.010 ↗
2. Agricultural wastes as aggregate in concrete mixtures-a review10.1016/j.conbuildmat.2013.11.074 ↗
3. Shape effect on compressive mechanical properties of compound concrete containing demolished concrete lumps10.1016/j.conbuildmat.2018.07.086 ↗
4. Recycling of industrial and agricultural wastes as alternative coarse aggregates: a step towards cleaner production of concrete
5. Waste glass as a supplementary cementitious material in concrete – critical review of treatment methods10.1016/j.cemconcomp.2009.02.001 ↗
6. Effects of sugarcane bagasse ash and nano eggshell powder on high-strength concrete properties
7. Effect of using a combination of rice husk and olive waste ashes on high-strength concrete properties
8. Engineering properties of sustainable green concrete incorporating eco-friendly aggregate of crumb rubber: a review10.1016/j.jclepro.2021.129251 ↗
9. Experimental and simulation study on the impact resistance of concrete to replace high amounts of fine aggregate with plastic waste
10. Performance studies on concrete with recycled coarse aggregates10.12989/acc.2016.4.4.263 ↗
11. Wang W., Wei W.Y., Gao S., et al. Agricultural and aquacultural waste as concrete components: A review. 2021, 8:762568.10.3389/fmats.2021.762568 ↗
12. Design of chained pneumatic punching automatic dried jujube pit removing machine
13. The content variation of phytochemicals in different parts of Chinese jujube from different Cultivars
14. Xie Y., Chu H.H., Li G.Y., et al. Preparation and uranium adsorption property of activated carbon from jujube nucleus. 2021, 36(1):1–8. (In Chinese).
15. Adsorptive scavenging of cationic dyes from aquatic phase by h3po4 activated indian jujube (Ziziphus mauritiana) seeds based activated carbon: isotherm, kinetics, and thermodynamic study
16. Mechanical properties of jujube pit/linear low density polyethylene composites
17. Performance of coconut shell as coarse aggregate in concrete10.1016/j.conbuildmat.2017.02.066 ↗
18. A study on the utilization of coconut shell as coarse aggregate in concrete
19. Mechanical and bond properties of coconut shell concrete10.1016/j.conbuildmat.2010.06.053 ↗
20. Utilization of oil palm kernel shell as lightweight aggregate in concrete – a review10.1016/j.conbuildmat.2012.08.026 ↗
21. Use of oil palm shell as replacement of coarse aggregate for investigating properties of concrete
22. Exploratory study of rubber seed shell as partial coarse aggregate replacement in concrete10.19026/rjaset.7.380 ↗
23. Eco-friendly utilization of corncob ash as partial replacement of sand in concrete10.1016/j.conbuildmat.2018.11.063 ↗
24. Experimental study on shrinkage performance of corncob recycled aggregate composite ecological concrete
25. Today’s concretes exposed to fire—test results and sectional analysis
26. The effect of high temperatures on the mechanical properties of concrete made with different types of aggregates10.1016/j.firesaf.2011.07.002 ↗
27. Ibrahim R.K., Muhammedemin H.M. The residual strength for different shaped high strength concrete specimens at high temperature. 2016, 2(1):21–27.10.23918/eajse.2414213 ↗
28. Detection of thermophysical properties for high strength concrete after exposure to high temperature10.1007/s11595-017-1568-z ↗
29. Evaluation of residual strength and durability aspect of concrete cube exposed to elevated temperature
30. Bond characteristics between early aged fly ash concrete and reinforcing steel bar after fire10.1016/j.conbuildmat.2017.04.184 ↗
31. Basic parameters test and 3D modeling of bond between high-strength concrete and ribbed steel bar after elevated temperatures10.1002/suco.201600005 ↗
32. Effects of re-curing on microstructure of concrete after high temperature exposure10.1016/j.conbuildmat.2017.11.005 ↗
33. A new perspective on nature of fire-induced spalling in concrete10.1016/j.conbuildmat.2018.06.204 ↗
34. Effects of heating followed by water quenching on strength and microstructure of ultra-high performance concrete10.1016/j.conbuildmat.2019.02.123 ↗
35. Effect of high-temperature on the mechanical and durability behaviour of concrete
36. Microstructural changes in concrete: postfire scenario10.1061/(ASCE)MT.1943-5533.0003449 ↗
37. Assessing some durability properties of sustainable lightweight oil palm shell concrete incorporating slag and manufactured sand10.1016/j.jclepro.2015.06.122 ↗
38. A study on some durability properties of coconut shell aggregate concrete10.1617/s11527-013-0230-2 ↗
39. JGJ 52–2006, Standard for technical requirements and test method of sand and crushed stone (or gravel) for ordinary concrete. Ministry of Construction of the People’s Republic of China, 2007.
40. Research progress in chemical constituents of zizyphus jujuba
41. Interaction between cement and chemical admixture from the point of cement hydration, absorption behaviour of admixture, and paste rheology10.1016/S0008-8846(99)00004-6 ↗
42. Effect of pine needle fiber reinforcement on the mechanical properties of concrete10.1016/j.conbuildmat.2021.122333 ↗
43. GB/T 17431.2–2010, Lightweight aggregates and its test methods—part 2: Test methods for lightweight aggregates. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, 2011.
44. Effect of coarse aggregate with different water absorption on strength and drying shrinkage of concrete
45. GB/T 50081–2019, Standard for test methods of concrete physical and mechanical properties. Ministry of Housing and Urban-Rural Development of the People's Republic of China, 2019.
46. Effect of exposure time and rates of heating and cooling on residual strength of heated concrete10.1680/macr.1986.38.136.151 ↗
47. Life cycle assessment of concrete made with high volume of recycled concrete aggregates and fly ash10.1016/j.resconrec.2018.07.004 ↗
48. Evaluating engineering properties and environmental impact of pervious concrete with fly ash and slag10.1016/j.jclepro.2019.117714 ↗
49. Handbook on life cycle assessment
50. A comparative study of environmental performance between prefabricated and traditional residential buildings in China10.1016/j.jclepro.2015.04.120 ↗
51. GB/T 50080–2016, Stand for test method of performance on ordinary fresh concrete. Ministry of Housing and Urban-Rural Development of the People's Republic of China, 2017.
52. The retarding action of sugars on cement hydration10.1016/0008-8846(83)90084-4 ↗
53. Influence of sucrose on cement hydration process
54. Mechanism of regulation set of sucrose in Portland cement
55. New insights into the effects of sugar on the hydration and microstructure of cement pastes10.1016/S0008-8846(01)00689-5 ↗
56. Hysteresis from multiscale porosity: modeling water sorption and shrinkage in cement paste10.1103/PhysRevApplied.3.064009 ↗
57. Shrinkage design model of concrete incorporating wet packing density10.1016/j.conbuildmat.2021.122448 ↗
58. Research progress on property, constitutive relation and failure mechanism of lightweight aggregate concrete
59. Influence mechanism of sucrose on hydration process of portland cement
60. GB/T 50010–2010, Code for design of concrete structures. Ministry of Housing and Urban-Rural Development of the People's Republic of China, 2010.
61. Unified calculation method of mechanical properties of concrete in tension
62. Unified calculation method of compressive mechanical properties of concrete
63. Unified calculation method of uniaxial mechanical properties of lightweight aggregate concrete
64. Sustainable applications for utilizing molybdenum tailings in concrete10.1016/j.jclepro.2020.122020 ↗
65. A comparative study on mechanical and environmental performance of concrete-filled steel tubes using molybdenum tailing aggregate10.1016/j.jcsr.2021.107100 ↗
66. Utilization of coal gangue as coarse aggregates in structural concrete10.1016/j.conbuildmat.2020.121212 ↗
67. Basalt fiber reinforced concrete: a compressive review on durability aspects10.3390/ma16010429 ↗
68. The behavior of hybrid fiber-reinforced concrete elements: a new stress-strain model using an evolutionary approach10.3390/app12042245 ↗