Tension and bond characteristics of foam concrete for repair applications
Source abstract
Abstract
In this study, foam concretes (FC) were developed, and their tension, shear, and bond properties were investigated for potential repair applications. Seven FC mixtures with varying combinations of ground granulated blast furnace slag (GGBS) and fly ash (FA) were prepared, along with one M25-grade conventional concrete mixture. The tension properties of both types of concrete were assessed through split tensile strength, flexural strength, and pull-off test while the shear strength and bond strength (with reinforcing bars) were determined using the slant shear test and pull-out test, respectively. The results indicated that the compressive strength of the FC mixtures at 28 days ranged from 21.98 to 40.08 MPa, satisfying the requirements of IS 456:2000 for M15 to M30-grade concrete. Furthermore, the split tensile strength of FC was in the range of 2.21 MPa to 2.83 MPa while M25-grade concrete showed a strength of 2.24 MPa. Shear strengths for FC and M25-grade concrete ranged between 6.67 MPa and 8.08 MPa, and 5.49 MPa, respectively. Additionally, tensile bond strengths of FC and M25-grade concrete fell within the range of 0.67 MPa to 1.46 MPa and 1.12 MPa, respectively. The bond strength obtained from the pull-out test for FC and M25-grade concrete was observed to vary within the range of 11.87 MPa to 23.26 MPa and 14.14 MPa, respectively. FC exhibited superior bond strength compared to M25-grade concrete with both the concrete substrate and reinforcing bars. It was also noted that the tension and bond strength of FC were linearly correlated with its compressive strength. Microstructure analysis indicated that macropores were isolated and discontinuous in all mixtures. The improvement in mechanical and bond properties was attributed to enhancements in the microstructure, and the ability of GGBS and FA particles to fill pores in the cementitious paste regions. In conclusion, FC showed promise as an alternative concrete repair material, with comparable or superior tensile and bonding properties compared to M25-grade concrete.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Magnesium Oxide Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (80)
Show source-provided references
1. Effects of interface roughness and interface adhesion on new-to-old concrete bonding10.1016/j.conbuildmat.2017.05.049 ↗
2. Experimental testing correlation of the different aged concrete bond strength involving the new tilted cube test (TCT)
3. Effect of surface preparation and bonding agent on the concrete-to-concrete interface strength10.1016/j.conbuildmat.2012.07.028 ↗
4. Factors affecting bond between new and old concrete
5. Are concrete-concrete bond tests comparable?10.1016/j.cemconcomp.2019.02.012 ↗
6. Investigation of the bond between concrete substrate and ECC overlays10.1061/(ASCE)MT.1943-5533.0000805 ↗
7. Freeze-thaw durability of shotcrete-concrete interface bonds in tension10.1016/j.coldregions.2023.103798 ↗
8. Bond strength of whitetoppings and bonded overlays constructed with self-compacting high-performance concrete10.1016/j.conbuildmat.2017.07.136 ↗
9. Standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension ( Pull-off Method)
10. Bond behaviour of normal/recycled concrete and corroded steel bars10.1016/j.conbuildmat.2013.06.091 ↗
11. Indian standard plain and reinforced concrete code of practice, Indian stand
12. Experimental study on bond properties between GFRP bars and self-compacting concrete10.1016/j.conbuildmat.2021.126186 ↗
13. Bond properties of lightweight concrete - A review10.1016/j.conbuildmat.2016.02.125 ↗
14. Concrete-to-concrete bond Strength: a review10.1016/j.conbuildmat.2022.129820 ↗
15. Slant shear bond strength between self compacting concrete and old concrete10.1016/j.conbuildmat.2016.11.023 ↗
16. Factors affecting bond strength of RC column jackets10.1016/j.aej.2016.01.014 ↗
17. Standard test method for flexural strength of concrete ( Using simple beam with third-point loading) 1
18. Treatment with nano-silica and bacteria to restore the reduced bond strength between concrete and repair mortar caused by aggressive removal techniques10.1016/j.cemconcomp.2021.104064 ↗
19. Analysis of in situ bond strength of bonded concrete overlay10.1016/j.conbuildmat.2016.02.062 ↗
20. Bond strength between blended slag and Class F fly ash geopolymer concrete with steel reinforcement10.1016/j.cemconres.2015.02.016 ↗
21. Effect of polypropylene and glass fiber on properties of lightweight concrete exposed to high temperature
22. Mechanical and light transmittance properties of high-performance translucent concrete
23. Effect of air agent on mechanical properties and microstructure of lightweight geopolymer concrete under high temperature
24. Effect of elevated temperatures on mechanical properties of lightweight geopolymer concrete
25. Investigating the mechanical and microstructure properties of fibre-reinforced lightweight concrete under elevated temperatures
26. Use of no-fines concrete as a building material: strength, durability properties and corrosion protection of embedded steel10.1016/j.cemconres.2013.02.006 ↗
27. Self-compacting lightweight aggregate concrete and its properties: a review10.1016/j.conbuildmat.2023.130861 ↗
28. Properties and applications of foamed concrete; a review10.1016/j.conbuildmat.2015.10.112 ↗
29. A classification of studies on properties of foam concrete10.1016/j.cemconcomp.2009.04.006 ↗
30. Effect of w/c ratio on air-void system of foamed concrete and their influence on mechanical properties10.1680/macr.2011.63.8.583 ↗
31. Laboratory test on foamed concrete-rock joints in direct shear10.1016/j.conbuildmat.2018.04.006 ↗
32. Effectiveness of foamed concrete density and locking patterns on bond strength of galvanized strip10.1016/j.conbuildmat.2016.04.047 ↗
33. Pull-out behavior of galvanized steel strip in foam concrete10.1186/2008-6695-5-24 ↗
34. Effects of foam content on chloride ingress and steel corrosion in foamed concrete10.1680/jmacr.20.00223 ↗
35. Lightweight foamed concrete mixture for structural use
36. Experimental research on properties of high-strength foamed concrete10.1061/(ASCE)MT.1943-5533.0000353 ↗
37. Preliminary views on the potential of foamed concrete as a structural material10.1680/macr.2005.57.1.21 ↗
38. IS:8112, Specification for 43 grade Ordinary Portland Cement, Indian Stand. Code. (2013) 17.
39. IS:12089, Specification for granulated slag for the manufacture of Portland slag cement, Bur. Indian Stand. New Delhi. (1987) 1–14.
40. IS:4031 (Part-2), Methods of Physical Tests for, Indian Stand. Code. 4031 (2013) 3–7.
41. IS 3812: Part 1, Pulverized Fuel Ash - Specification: Part 1 For Use as Pozzolana in Cement, Cement Mortar and Concrete, Bur. Indian Stand. New Delhi, India. (2013) 1–12.
42. Sorption characteristics of foam concrete10.1016/j.cemconres.2007.05.010 ↗
43. The effect of high fly ash content on the compressive strength of foamed concrete10.1016/S0008-8846(00)00430-0 ↗
44. On void structure and strength of foamed concrete made without/with additives10.1016/j.conbuildmat.2015.03.093 ↗
45. IS 10262: 2019, Concrete Mix Proportioning — Guidelines, Indian Stand. Code. 02 (2019).
46. Foaming agents for use in producing cellular concrete using preformed foam 1
47. K.C. Brady, G.R.A. Watts, M.R. Jones, Specification for foamed concrete, Prep. Qual. Serv. Civ. Eng. Highw. Agency. (2001). https://trl.co.uk/sites/default/files/AG39.pdf.
48. RC6 Bond test for reinforcement steel. 2. Pull-out test
49. Standard test method for splitting tensile strength of cylindrical concrete specimens
50. ASTM C882, Standard Test Method for Bond Strength of Latex Systems Used With Concrete By, ASTM Int. i (2020). https://doi.org/10.1520/C0882.
51. Standard practice for capping cylindrical concrete specimens
52. Standard test method for apparent shear strength of single-lap-joint adhesively bonded metal specimens by tension loading
53. Standard test method for bond strength of fiber-reinforced polymer matrix composite bars to concrete by pullout testing
54. Standard test method for microscopical determination of parameters of the air-void system in hardened concrete 1
55. IS 456:2000, Indian Standard PLAIN AND REINFORCED CONCRETE-, Bur. Indian Stand. New Delhi. 31 (2021).
56. The role of fly ash microsphere in the microstructure and macroscopic properties of high-strength concrete10.1016/j.cemconcomp.2017.07.021 ↗
57. An experimental study on corrosion resistance of concrete with ground granulate blast-furnace slag10.1016/j.cemconres.2004.11.010 ↗
58. Physical and mechanical properties of foam concretes containing granulated blast furnace slag as fine aggregate10.1016/j.conbuildmat.2019.117774 ↗
59. Nature of C-S-H in hardened cements10.1016/S0008-8846(99)00168-4 ↗
60. Hydration heat, strength and microstructure characteristics of UHPC containing blast furnace slag
61. Air-void characterisation of foam concrete10.1016/j.cemconres.2006.10.009 ↗
62. Effect of fly ash fineness on compressive strength and pore size of blended cement paste10.1016/j.cemconcomp.2004.07.003 ↗
63. Physical and pozzolanic action of mineral additions on the mechanical strength of high-performance concrete10.1016/S0958-9465(01)00057-9 ↗
64. Reactive ultra-fine fly ash as an additive for cement-based materials
65. Mehta · Microstruct., Prop. Mater., Third Ed. · 2006
66. Experimental research on properties of high-strength foamed concrete10.1061/(ASCE)MT.1943-5533.0000353 ↗
67. Experimental testing correlation of the different aged concrete bond strength involving the new tilted cube test (TCT)
68. The effect of the porosity within the interfacial zone between layers on pull-off adhesion10.1016/j.conbuildmat.2017.07.080 ↗
69. Pull-off characterization of FRCM/Concrete interface10.1016/j.compositesb.2019.02.025 ↗
70. Bond strength of steel deformed rebars embedded in artificial lightweight aggregate concrete10.1080/01694243.2012.687552 ↗
71. Influence of lightweight aggregate on the bond properties of concrete with various strength grades10.1016/j.conbuildmat.2015.03.040 ↗
72. Bonding of steel reinforcement in structural expanded clay lightweight aggregate concrete: The influence of failure mechanism and concrete composition10.1016/j.conbuildmat.2014.04.122 ↗
73. Bond strength of rubberized concrete with deformed steel bar10.1016/j.conbuildmat.2020.121730 ↗
74. Comparison of test methodologies to evaluate steel-concrete bond strength of thin reinforcing bar10.1016/j.conbuildmat.2018.06.109 ↗
75. Electrical resistivity and piezoresistivity of cement mortar containing ground granulated blast furnace slag10.1016/j.conbuildmat.2020.120243 ↗
76. Microstructural study of Portland cement partially replaced with fly ash, ground granulated blast furnace slag and silica fume as determined by pozzolanic activity10.1016/j.conbuildmat.2019.117561 ↗
77. On void structure and strength of foamed concrete made without/with additives10.1016/j.conbuildmat.2015.03.093 ↗
78. Effect of ground granulated blast furnace slag (GGBFS) on RCCP durability10.1016/j.conbuildmat.2017.03.019 ↗
79. Promoting utilization rate of ground granulated blast furnace slag (GGBS): Incorporation of nanosilica to improve the properties of blended cement containing high volume GGBS10.1016/j.jclepro.2021.130096 ↗
80. A study on creep and drying shrinkage of high performance concrete10.1016/S0008-8846(01)00539-7 ↗