Study of changes in microstructure and metal interface Cu/Al during bimetallic construction wire straining
Source abstract
Abstract
This article investigates the effect of a new processing technology on the change in microstructure and mechanical properties of bimetallic aluminum-copper wire. This technology makes it possible to produce a new generation of wire for use in the construction of new overhead lines and reconstruction of old ones. The study was conducted using a transmission electron microscope, EBSD analysis, tensile tests, and determination of microhardness and electrical conductivity. The results of the study show that an ultrafine-grained copper-aluminum composite with a gradient structure is formed during straining by ECAP-drawing. Annealing after straining at 200 °C increases the strength of the interfacial connection between Cu and Al and improves the strength characteristics of the bimetallic aluminum-copper wire. The use of such aluminum-copper wires for overhead transmission lines allows to reduce the wire cross-section and, accordingly, wind loads, as well as to increase the strength properties without an additional increase in the total weight of the wire.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · Mechanical stress and fatigue analysis · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Research of influence equal channel angular pressing on the microstructure of copper
2. Chemical and phase transitions in oxidized manganese ore in the presence of carbon10.3103/S0967091217090078 ↗
3. Development and testing of low-energy intensive technology of receiving sulfate-resistant and road Portland cement10.18321/ectj683 ↗
4. Theoretical studies of the heat transfer process and the hydrodynamics of a condensate film by numerical experiment10.31788/RJC.2022.1536741 ↗
5. Modeling of non-ferrous metallurgy waste disposal with the production of iron silicides and zinc distillation10.3390/ma15072542 ↗
6. Mathematical description of the process of film condensation of vapors from steam-gas mixtures10.31788/RJC.2022.1536695 ↗
7. Experimental analysis of the stress state of a prestressed cylindrical shell with various structural parameters10.3390/ma15144996 ↗
8. Receiving portland cement from technogenic raw materials of South Kazakhstan10.18321/ectj890 ↗
9. Changes in microstructure and properties of austenitic steel AISI 316 during high-pressure torsion
10. Influence of combined process rolling-pressing on microstructure and mechanical properties of copper10.1016/j.proeng.2014.10.180 ↗
11. FEM simulation of copper busbar pressing on the continuous extrusion line "Conform"10.4028/www.scientific.net/SSP.284.547 ↗
12. Theoretical analysis of bimetallic rods extrusion process in double reduction die10.1016/j.jmatprotec.2004.04.052 ↗
13. Development of a thermomechanical treatment mode for stainless-steel rings10.3390/ma15144930 ↗
14. Evolution of the microstructure and mechanical properties of copper under ECAP with intense cooling10.1007/s11041-020-00544-x ↗
15. Structure and mechanical properties of aluminum alloy 2024 after cryogenic cooling during ECAP
16. Bulk nanostructured materials from severe plastic deformation10.1016/S0079-6425(99)00007-9 ↗
17. Microstructural evolution and micro/meso-deformation behavior in pure copper processed by equal-channel angular pressing10.1016/j.msea.2016.03.016 ↗
18. Evolution of microstructure and mechanical properties of steel in the course of pressing–drawing10.1134/S0031918X17110072 ↗
19. Research of combined process rolling-pressing influence on the microstructure and mechanical properties of aluminium10.4028/www.scientific.net/AMR.814.68 ↗
20. Study of the properties of antifriction rings under severe plastic deformation10.3390/ma15072584 ↗
21. High-strength fiber-reinforced concrete containing techno genic raw materials and composite binders with use of nanodispersed powder
22. Effect of severe plastic deformation on the conductivity and strength of copper-clad aluminium conductors
23. Experimental and molecular dynamic study of grain refinement and dislocation substructure evolution in HSLA and IF steels after severe plastic deformation10.3390/met10091122 ↗
24. Microstructure and electrical conductivity of aluminium/steel bimetallic rods processed by severe plastic deformation10.1007/s10853-016-9973-9 ↗
25. Formation of ultra-fine copper grains in copper-clad aluminum wire10.1016/j.scriptamat.2010.05.010 ↗
26. Optimization of raw mix using technogenic waste to produce cement clinker
27. Quality of bimetal Al-Cu joint after explosive cladding
28. Electrical, corrosion, and mechanical properties of aluminum-copper joints produced by explosive welding10.1007/s11665-012-0203-6 ↗
29. Thermodynamic simulation of environmental and population protection by utilization of technogenic tailings of enrichment10.3390/ma15196980 ↗
30. New combined process pressing-drawing and impact on properties of deformable aluminum wire10.1016/j.proeng.2014.10.181 ↗
31. Forming ultrafine-grain structure in steel wire by continuous deformation10.3103/S0967091210060203 ↗
32. Fabrication of aluminum/copper clad composite using hot hydro static extrusion process and its material characteristics10.1016/j.msea.2004.05.051 ↗
33. Thermodynamic simulation of silicon and iron reduction and zinc and lead distillation in zincoligonite ore-carbon systems10.3103/S1067821214060121 ↗
34. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
35. The cleavage strength of polycrystals
36. Severe plastic deformation and thermomechanical processing: nanostructuring and properties10.3390/met10101306 ↗
37. Bulk ultrafine-grained interstitial-free steel processed by equal-channel angular pressing followed by flash annealing10.1007/s11665-016-2392-x ↗
38. Effect of initial structural state on formation of structure and mechanical properties of steels under ECAP10.1007/s11041-018-0227-0 ↗
39. Study of a reagent-emulsifier for the preparation of reverse water-oil emulsions used for well-killing
40. Analysis of stress-strain state for a cylindrical tank wall defected zone10.3390/ma15165732 ↗
41. Effect of the initial structural state of cr–mo high-temperature steel on mechanical properties after equal-channel angular pressing10.1134/S0031918X19020133 ↗
42. Analysis of a Stress-strain state of a cylindrical tank wall vertical field joint zone10.3390/buildings12091445 ↗
43. Effect of cryogenic cooling after ecap on mechanical properties of aluminum alloy D1610.1007/s11041-019-00406-1 ↗
44. Features of change of the structure and mechanical properties of steel at ECAP depending on the initial state
45. Production of surface layer with gradient microstructure and microhardess on copper by high pressure surface rolling10.3390/met10010073 ↗
46. Continuous processing of ultrafine grained A1 by ECAP-conform10.1016/j.msea.2004.04.021 ↗
47. Flow characteristics of continuous shear drawing of high carbon steel10.1016/j.ijmecsci.2011.03.008 ↗
48. Current trends to obtain metals and alloys with ultrafine-grained structure
49. Extrolling: combine extrusion and rolling
50. Evolution of the microstructure and mechanical properties of copper during the pressing–drawing process10.1134/S0031918X18090132 ↗
51. Hardening of bimetallic wires from secondary materials used in the construction of power lines10.3390/ma15113975 ↗
52. Change in the microstructure and properties of steel-aluminum wire during “ECA-pressing - drawing” process
53. A review of focused ion beam milling techniques for TEM specimen preparation10.1016/S0968-4328(99)00005-0 ↗
54. Humphreys · 2004
55. Fiber texture formation and mechanical properties in drawn fine copper wire10.4028/www.scientific.net/MSF.157-162.715 ↗
56. On the texture of aluminum rods extruded under various conditions10.2464/jilm.18.81 ↗
57. Strain-path effects on the evolution of microstructure and texture during the severe-plastic deformation of aluminum10.1007/BF02586120 ↗
58. Humphreys · 1995
59. Interfacial microstructure evolution of copper/aluminium laminates with different annealing processes
60. Hardening by annealing: Insights from different alloys
61. Strengthening during heat treatment of HPT processed copper and nickel10.1016/j.msea.2018.11.010 ↗
62. Features of developing unique architectural solutions using digital methods based on visual programming