journal article·2022-06Open access

Behavior evaluation of sustainable high strength geopolymer concrete based on fly ash, metakaolin, and slag

Mohamed Amin, Yara Elsakhawy, Khaled Abu el-hassan, Bassam Abdelsalam Abdelsalam

Abstract

The environmental challenge such as high energy demand, consuming raw materials, large CO2 emissions, and many other reasons associated with ordinary Portland cement manufacturing-led us to search for alternatives such as green concrete or geopolymer concrete. In this paper industrial wastes like fly ash, metakaolin, and granulated blast furnace slag were used as a base for high strength geopolymer concrete (HSGC). Four high strength concrete (HSC) mixes with Portland cement were produced for comparison with fifteen different geopolymer concrete mixes. All mixes were cast, cured, and tested. Slump and air content were measured as fresh properties for both HSC and HSGC mixes. Compressive strength at 3, 7, 28, and 91 days, splitting tensile strength, flexural strength, and modulus of elasticity were also measured and analyzed as mechanical properties. Durability properties like water permeability coefficient, drying shrinkage at 3, 7, 14, 21, 28, 56, and 91 days and temperature studies from 100 ° to 700 ° were investigated. Scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) spectroscopy analysis of cement and geopolymer concrete mixes were conducted. Regarding fresh properties results showed that the geopolymer concrete based on slag with 500 kg/m3 showed 225 mm slump, while in hardened properties, the mix contained 200 kg of metakaolin with 300 kg of slag had the greatest compressive strength in both early and late age 63.3, 82.6 MPa, respectively, also had the greatest splitting tensile strength 6.2 MPa, flexural strength reached 9.2 MPa and modulus of elasticity was 37.68 GPa. Also, the coefficient of permeability decreases as the granulated blast furnace slag increases. The mineral additives contributed to reducing the dry shrinkage of geopolymer concrete. SEM images exhibited that the geopolymer matrix contained more dispersed small-sized pores which indicate a higher compressive strength absolutely than other experimental mixes.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Magnesium Oxide Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. Chemistry of geopolymeric systems, terminology
2. Properties of geopolymer cements
3. Geopolymer technology: the current state of the art10.1007/s10853-006-0637-z ↗
4. Effect of high temperatures on mechanical, radiation attenuation and microstructure properties of heavyweight geopolymer concrete
5. Effect of elevated temperatures on mechanical properties of lightweight geopolymer concrete
6. Geopolymers and geopolymeric materials10.1007/BF01904446 ↗
7. Geopolymer technology: the current state of the art10.1007/s10853-006-0637-z ↗
8. Industrially interesting approaches to “low-CO2” cements10.1016/j.cemconres.2004.01.021 ↗
9. Excavated soil waste as fine aggregate in fly ash based geopolymer mortar10.1016/j.clay.2017.05.038 ↗
10. Rheological and the fresh state properties of alkali-activated mortars by blast furnace slag10.3390/ma14082069 ↗
11. Mechanical, physical and durability properties of activated alkali cement based on blast furnace slag as a function of% Na2O
12. Efficiency of rice husk ash and fly ash as reactivity materials in sustainable concrete
13. Thermal effects of activators on the setting time and rate of workability loss of geopolymers10.1016/j.ceramint.2016.09.092 ↗
14. J. Davidovits, Geopolymer, Chemistry and Applications, Geopolymer Institute, 2008.
15. Statistical analysis of strength development as a function of various parameters on activated metakaolin/slag cements10.1111/j.1551-2916.2009.03414.x ↗
16. S. Astutiningsih, Y.N. Liu, Geopolymerisation of Australian slag with effective dis- solution by the alkali, 2005.
17. Geopolymer formation and its unique properties10.1007/s00254-006-0308-z ↗
18. Novel geopolymer based composites with enhanced ductility10.1007/s10853-006-0527-4 ↗
19. Geopolymers and geopolymeric materials10.1007/BF01904446 ↗
20. Production of geopolymer concrete by utilizing volcanic pumice dust
21. Potential applications of geopolymer concrete in construction: a review
22. Preparation, structure and properties of hybrid materials based on geopolymers and polysiloxanes10.1016/j.matdes.2015.08.006 ↗
23. Circular economy and durability in geopolymers ceramics pieces obtained from glass polishing waste10.1111/ijac.13780 ↗
24. Effect of the addition and processing of glass polishing waste on the durability of geopolymeric mortars
25. Performance of geopolymer tiles in high temperature and saturation conditions10.1016/j.conbuildmat.2021.122994 ↗
26. Wallah · 2006
27. Medium-term phase stability of Na2O–Al2O3–SiO2–H2O geopolymer systems10.1016/j.cemconres.2007.10.003 ↗
28. R.R..Lloyd,TheDurabilityofInorganicPolymerCements,UniversityofMelbourne, Melbourne, 2008 Ph.D. Thesis.
29. Propertiesofanagedgeopolymersynthesizedfromcalcined ore-dressing tailing of bauxite and slag10.1016/j.cemconres.2017.05.017 ↗
30. Performance of blended metakaolin/blastfurnace slag alkali-activated mortars10.1016/j.cemconcomp.2016.04.008 ↗
31. A review on microstructural study and compressive strength of geopolymer mortar, paste and concrete10.1016/j.conbuildmat.2018.07.075 ↗
32. Performance evaluation and some durability characteristics of environmental friendly palm oil clinker based geopolymer concrete10.1016/j.jclepro.2017.05.002 ↗
33. Engineering and durability properties of concretes based on alkali-activated granulated blast furnace slag/ metakaolin blends10.1016/j.conbuildmat.2012.01.017 ↗
34. Rheology and setting of alkali-activated slag pastes and mortars: effect of organic admixture
35. Fly ash-based geopolymers: the relationship between composition, pore structure and efflorescence10.1016/j.cemconres.2014.06.004 ↗
36. Efflorescence control in geopolymer binders based on natural pozzolan10.1016/j.cemconcomp.2011.07.007 ↗
37. R. Pouhet, Formulation and durability of metakaolin-based geopolymers, Université de Toulouse, Université Toulouse III-Paul Sabatier, 2015.
38. Efflorescence control in geopolymer binders based on natural pozzolan10.1016/j.cemconcomp.2011.07.007 ↗
39. Behavior of geopolymer concrete deep beams containing waste aggregate of glass and limestone as a partial replacement of natural sand
40. Fabrication of thermal insulation geopolymer bricks using ferrosilicon slag and alumina waste
41. BS EN 197-1 · 2011
42. ASTM C618 Class F. "Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete".
43. ASTM C · 2003
44. ASTM-C-494 Type G Standard Specification for Chemical Admixtures for Concrete Type G—water reducing, high range, and retarding. The materials used in the concrete mixtures shall include Type I or Type II cement, pozzolan, fine and coarse aggregates, and air-entraining admixture.
45. BS EN 934 part 2: 2001 Admixtures for concrete, mortar and grout. Concrete admixtures. Definitions, requirements, conformity, marking and labelling.
46. ASTM-C-143–15a Standard Test Method for Slump of Hydraulic-Cement Concrete.
47. ASTM-C-231–17a Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method.
48. BS-1881: part-116-2004 Testing concrete. Method for determination of compressive strength of concrete cubes.
49. ASTM-C496–11 Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens.
50. ASTM-C78–16 Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading).
51. BS-1881: part-207:1992 Testing concrete. Recommendations for the assessment of concrete strength by near-to-surface tests.
52. ASTM-C469–14 Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression.
53. Technical Committee 200-HTC Ulrich. schneider@ tuwien. ac. at. "Recommendation of RILEM TC 200-HTC: mechanical concrete properties at high temperatures—modelling and applications: Part 1: introduction—general presentation10.1617/s11527-007-9285-2 ↗
54. Effects of nano cotton stalk and palm leaf ashes on ultrahigh-performance concrete properties incorporating recycled concrete aggregates10.1016/j.conbuildmat.2021.124196 ↗
55. Engineering properties of self-cured normal and high strength concrete produced using polyethylene glycol and porous ceramic waste as coarse aggregate10.1016/j.conbuildmat.2021.124243 ↗
56. Effect of air agent on mechanical properties and microstructure of lightweight geopolymer concrete under high temperature
57. High-strength geopolymer concrete- properties, advantages and challenges10.11648/j.am.20180702.11 ↗
58. Optimization approach of granulated blast furnace slag and metakaolin based geopolymer mortars10.1016/j.conbuildmat.2018.11.251 ↗
59. Investigation of engineering properties of normal and high strength fly ash based geopolymer and alkali-activated slag concrete compared to ordinary Portland cement concrete10.1016/j.conbuildmat.2018.11.083 ↗
60. Mechanical characterization and assessment of composite geopolymer concrete10.1016/j.matpr.2020.06.319 ↗
61. Effect of metakaolin replaced granulated blast furnace slag on fresh and early strength properties of geopolymer mortar10.1016/j.asej.2016.11.011 ↗
62. Engineering properties of inorganic polymer concretes (IPCs)10.1016/j.cemconres.2006.10.008 ↗
63. Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition10.1016/j.conbuildmat.2014.05.080 ↗
64. Effect of water addition, plasticizer and alkaline solution constitution on fly ash based geopolymer concrete performance10.1016/j.conbuildmat.2016.06.062 ↗
65. Design of geopolymer concrete with GGBFS at ambient curing condition using Taguchi method10.1016/j.conbuildmat.2017.02.131 ↗
66. Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition10.1016/j.conbuildmat.2014.05.080 ↗
67. Optimisation of rheological parameters and mechanical properties of superplasticised cement grouts containing metakaolin and viscosity modifying admixture10.1016/j.conbuildmat.2012.07.102 ↗
68. Observations on the rheological response of alkali activated fly ash suspensions: the role of activator type and concentration10.1007/s00397-014-0793-z ↗
69. Rheological study of cement paste with metakaolin and/or limestone filler using mixture design of experiments10.1016/j.conbuildmat.2017.03.001 ↗
70. Effects of local metakaolin addition on rheological and mechanical performance of self-compacting limestone cement concrete10.1080/01694243.2019.1571737 ↗
71. Investigation on fundamental properties of microfine cement and cement-slag grouts10.1016/j.conbuildmat.2017.05.188 ↗
72. The effect of different Na2O and K2O ratios of alkali activator on compressive strength of fly ash based-geopolymer
73. The rheological, fresh and strength effects of cold-bonded geopolymer made with metakaolin and slag for grouting
74. Effect of ground granulated blast-furnace slag on the hydration and properties of cement paste10.1680/jadcr.17.00166 ↗
75. An overview on rheology, mechanical properties and durability of high volume slag used as a cement replacement in paste, mortar and concrete10.1016/j.conbuildmat.2018.07.150 ↗
76. Adam · 2009
77. Setting time and 7-day strength of geopolymer mortar with various binders10.1016/j.conbuildmat.2018.08.025 ↗
78. Development of ultra-high-performance geopolymer concrete10.1680/macr.13.00057 ↗
79. Strength and chloride ion penetration resistance of ultra-high-performance fiber reinforced geopolymer concrete10.1016/j.istruc.2021.03.112 ↗
80. Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition10.1016/j.conbuildmat.2014.05.080 ↗
81. Bond strength between blended slag and Class F fly ash geopolymer concrete with steel reinforcement10.1016/j.cemconres.2015.02.016 ↗
82. Fly ash-based geopolymer concrete
83. Geopolymer synthesis using alkaline activation of natural zeolite10.1016/j.conbuildmat.2010.04.052 ↗
84. Effect of Na2SiO3/NaOH ratios and NaOH molarities on compressive strength of fly-ash-based geopolymer
85. Study of various properties of geopolymer concrete – a review
86. Strength development of recycled concrete aggregate stabilized with fly ash-rice husk ash based geopolymer as pavement base material10.1080/14680629.2019.1593884 ↗
87. Alkali-activated fly ashes: a cement for the future10.1016/S0008-8846(98)00243-9 ↗
88. The geopolymerization of alumino-silicate materials10.1016/S0301-7516(99)00074-5 ↗
89. Compressive strength and embodied energy optimization of fly ash based geopolymer concrete
90. Mechanical characterization and assessment of composite geopolymer concrete10.1016/j.matpr.2020.06.319 ↗
91. Hybrid alkaline cements. Part I: fundamentals cimenturi hibride alcaline: partea I. Fundamente ▲ hybrid alkaline cements: part I. Fundamentals
92. The coexistence of geopolymeric gel and calcium silicate hydrate at the early stage of alkaline activation10.1016/j.cemconres.2004.10.042 ↗
93. The mechanical properties of fly ashbased geopolymer concrete with alkaline activators10.1016/j.conbuildmat.2013.05.069 ↗
94. Performance of an alkaliactivated slag concrete reinforced with steel fibers10.1016/j.conbuildmat.2007.10.027 ↗
95. ACI Committee 363, Report on high strength concrete (ACI 363R-92)”, American Concrete Institute, Farmington Hills Mich. 1992 55.
96. Committee European du Beton , “State-of the-art report on high strength concrete”, CEB Bulletin 197 Aug Lausanne, Switz. 1990 61.
97. On the development of fly ash-based geopolymer concrete
98. The effects of ground granulated blast-furnace slag blending with fly ash and activator content on the workability and strength properties of geopolymer concrete cured at ambient temperature10.1016/j.matdes.2014.05.001 ↗
99. Geopolymer concrete: a concrete of the next decade
100. Fracture behaviour of heat cured fly ash based geopolymer concrete10.1016/j.matdes.2012.08.005 ↗