Plastic Behavior of Metals at Large Strains: Experimental Studies Involving Simple Shear
Source abstract
Abstract
Two experimental devices that promote simple shear are used to investigate the plastic behavior of metals under very large strains. First, researches on the anisotropic behaviors of sheets of metals performed with the help of the planar simple shear test are reviewed. In particular, it is shown that, with this device, stage IV may be reached and analyzed on polycrystals as well as on single crystals. The second part is devoted to equal channel angular extrusion, which is known to promote grain refinement after several passes. A direct comparison of the crystallographic textures measured on sheared and on extruded samples confirms that the extrusion promotes massively simple shear. Besides, the grain refinement is measured with a dedicated transmission electron microscopy (TEM) attachment. It is shown that the grain size decreases regularly for a low carbon steel as well as for copper, down to around 1 μm. It is argued that the sustained hardening in stage IV is a mechanical signature of the grain size decrease. The trend is interpreted and reproduced quantitatively with the help of a simple modeling approach.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · High-Velocity Impact and Material Behavior · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Grenoble INP, SIMaP/GPM2, CNRS-UJF, BP 46-38402, Saint Martin d’Hères Cedex, France
References (53)
Show source-provided references
1. Large Strain Work Hardening and Textures
2. Substructure and Strengthening of Heavily Deformed Single and Two-Phase Metallic Materials10.1051/jp3:1991168 ↗
3. Cold Work Hardening in Stage IV and V of F.C.C. Metals—I. Experiments and Interpretation
4. Application of the Plane Simple Shear Test for Determination of the Plastic Behaviour of Solid Polymers at Large Strains10.1007/BF00745590 ↗
5. A Proposal of a Planar Simple Shear Test in Sheet Metals
6. Plastic Anisotropy of Sheet Metals Determined by Simple Shear Tests10.1016/S0921-5093(97)00486-3 ↗
7. Anisotropic Strain Hardening Behavior in Simple Shear for Cube Textured Aluminum Alloy Sheets10.1016/j.ijplas.2005.03.014 ↗
8. Shear of Prestrained Steel Specimens10.1016/0036-9748(87)90255-9 ↗
9. Dislocation Substructures in Mild Steel Deformed in Simple Shear10.1016/0921-5093(89)90331-6 ↗
10. Plastic Flow for Non-Monotonic Loading Conditions of an Aluminum Alloy Sheet Sample10.1016/S0749-6419(02)00020-7 ↗
11. Towards an Accurate Description of the Anisotropic Behaviour of Sheet Metals Under Large Plastic Deformations: Modelling, Numerical Analysis and Identification10.1016/j.ijplas.2006.03.010 ↗
12. Work-Hardening Behavior of Mild Steel Under Stress Reversal at Large Strains10.1016/0749-6419(92)90006-X ↗
13. A Comparison of the Mechanical Behaviour of an AA1050 and a Low Carbon Steel Deformed Upon Strain Reversal10.1016/j.actamat.2004.10.046 ↗
14. Work-Hardening Model for Polycrystalline Metals Under Strain Reversal at Large Strains10.1016/j.actamat.2007.01.003 ↗
15. Microstructural Evolution Over a Large Strain Range in Aluminium Deformed by Cyclic-Extrusion–Compression10.1016/S0921-5093(98)00988-5 ↗
16. Bulk Nanostructured Materials From Severe Plastic Deformation10.1016/S0079-6425(99)00007-9 ↗
17. Materials Processing by Simple Shear10.1016/0921-5093(95)09705-8 ↗
18. Structural and Mechanical Properties in AA 5083 Processed by ECAE10.1179/026708300101507424 ↗
19. Principles of Equal-Channel Angular Pressing as a Processing Tool for Grain Refinement10.1016/j.pmatsci.2006.02.003 ↗
20. Novel Ultra-High Straining Process for Bulk Materials-Development of the Accumulative Roll-Bonding (ARB) Process10.1016/S1359-6454(98)00365-6 ↗
21. Strength and Ductility of Ultrafine Grained Aluminum and Iron Produced by ARB and Annealing10.1016/S1359-6462(02)00282-8 ↗
22. Ultra Grain Refinement and Hardening of IF-Steel During Accumulative Roll-Bonding10.1016/j.msea.2005.06.058 ↗
23. Neue Ergebnisse über die Verfestigung bei des plastischen Verformung von Kristallen. I. Schubverformung von langen Kristallen
24. The Flow Law of Mild Steel Under Monotonic or Complex Strain Path
25. Influence of Normal Stress on Deformation by Shear of Oriented Fe-Si Alloy Single-Crystals
26. Formation of Slip Bands in Aluminum Single-Crystals at 600°C
27. Non-Destructive Bulk Detection of Localized Straining by Gamma-Ray Diffractometry. Application to a Sheared Single Crystal of CMSX-2 Superalloy10.1002/pssa.2211480207 ↗
28. Simple Shear Deformation of Iron-Silicon Single-Crystals10.1016/0956-716X(90)90303-X ↗
29. Strain Hardening of Iron by Severe Plastic Deformation
30. Alberti, J. M. , 1984, “Large Plastic Deformation in Polycrystalline Cu and Al at Low Temperature,” Ph.D. thesis, University of Navarra, Spain.
31. Cold Work Hardening of Al From Shear Deformation up to Large Strains10.1016/S1359-6462(99)00184-0 ↗
32. Stage IV Work Hardening in Cubic Metals
33. Microstructure Development During Equal Channel Angular Drawing of Al at Room Temperature10.1016/S1359-6462(98)00234-6 ↗
34. The Development of Microstructure and the Influence of Processing Route During Equal Channel Angular Drawing of Pure Aluminum10.1016/S0921-5093(98)01129-0 ↗
35. On the Impossibility of Multi-Pass Equal-Channel Angular Drawing10.1016/S1359-6462(02)00089-1 ↗
36. Texture Evolution During Equal Channel Angular Forging and Dislocation Boundary Misorientations After Severe Plastic Deformation
37. Observations and Issues on Mechanisms of Grain Refinement During ECAP Process10.1016/S0921-5093(00)00978-3 ↗
38. Effect of Die Angle on the Deformation Texture of Copper Processed by Equal Channel Angular Extrusion10.1016/S0921-5093(00)01881-5 ↗
39. Texture Development and Simulation in Copper During Route B—Equal Channel Angular Pressing
40. Modelling Texture Development During Equal Channel Angular Extrusion of Aluminium10.1016/S1359-6454(02)00055-1 ↗
41. Deformation Paths Related to Equal Channel Angular Extrusion10.1016/S0921-5093(02)00027-8 ↗
42. Theory of Torsion Texture Development10.1016/0001-6160(84)90050-6 ↗
43. Textural Evolution During Equal Channel Angular Extrusion Versus Planar Simple Shear
44. Analysis of Texture Evolution in Equal Channel Angular Extrusion of Copper Using a New Flow Field10.1016/j.actamat.2003.12.027 ↗
45. Rapid Spot Diffraction Patterns Identification Through Template Matching
46. Orientation Maps Derived From TEM Diffraction Patterns Collected With an External CCD Camera
47. Coupled Microstructural Observations and Local Texture Measurements With an Automated Crystallographic Orientation Mapping Tool Attached to a TEM10.1002/mawe.200500923 ↗
48. Kinetics of Flow and Strain-Hardening10.1016/0001-6160(81)90112-7 ↗
49. Microstructure-Related Constitutive Modelling of Plastic Deformation
50. New Phenomena in the Plasticity of Semiconductors and FCC Metals at High Temperatures. II. Analysis of Experimental Data
51. A Comparison of the Strength and Microstructure of Heavily Cold Worked Cu-20% Nb Composites Formed by Different Melting Procedures10.1016/0036-9748(87)90266-3 ↗
52. The Stresses and Work Hardening Rates of Mild Steel With Different Dislocation Patterns
53. A New Mechanism of Work Hardening in the Late Stages of Large Plastic Flow in F. C. C. and Diamond Cubic Crystals10.1016/0956-7151(93)90058-Z ↗