Nonproportional Low Cycle Fatigue Criterion for Type 304 Stainless Steel
Source abstract
Abstract
This paper describes a multiaxial low cycle fatigue parameter for correlating Hues under nonproportional loadings. Constant amplitude low cycle fatigue tests were carried out under 14 proportional and complex nonproportional cyclic strain paths using type 304 stainless steel hollow cylinder specimens at room temperature. In nonproportional loading tests, fatigue lives are decreased by as much as a factor of 10 in comparison with those in proportional loading tests with the same strain range. Reduction in fatigue life due to nonproportional loading is closely related to additional nonproportional cyclic hardening. The product of the maximum principal stress and strain ranges correlated the nonproportional fatigue data. A nonproportional cyclic hardening parameter computed from the strain path is also proposed that allows life estimates to be obtained directly from the strain history without the need for a cyclic plasticity model.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Fire effects on concrete materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Faculty of Engineering, Fukui University, 9-1 Bunkyo 3-chome Fukui, 910, Japan
Department of Mechanical Engineering, Faculty of Science and Engineering, Ritsumeikan University, 1916 Noji-cho Kusatsu-shi Shiga, 525-77, Japan
Department of Mechanical and Industrial Engineering, University of Illinois, 140 Mechanical Engineering, 1206 West Green Street, Urbana, IL 61801
References (25)
Show source-provided references
1. ASME Code Case N-47, 1978, Case of ASME Boiler and Pressure Vessel Code, Case N-47, Class 1, Section 3, Division 1, ASME.
2. Benallal A. , and MarquisD., 1987, “Constitutive Equations for Nonproportional Cyclic Elasto-Viscoplasticity,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 109, No. 4, pp. 326–336.10.1115/1.3225985 ↗
3. Doong S. H. , SocieD. F., and RobertsonI. M., 1990, “Dislocation jubstructures and Nonproportional Hardening,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 112, No. 4, pp. 456–465.10.1115/1.2903357 ↗
4. Doong S. H. , and SocieD. F., 1991, “Constitutive Modeling of Metals Under Nonproportional Loading,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 113, No. 1, pp. 23–30.10.1115/1.2903379 ↗
5. Fatemi A. , and SocieD. F., 1988, “A Critical Plane Approach to Multiaxial Fatigue Damage Including Out-of-Phase Loading,” Fatigue and Fracture of Engineering Materials and Structures, Vol. 11, No. 3, pp. 149–165.10.1111/j.1460-2695.1988.tb01169.x ↗
6. Itoh, T., Sakane, M., Ohnami, M., Takahashi, Y., and Ogata, T., 1992a, “Nonproportional Multiaxial Low Cycle Fatigue Using Cruciform Specimen,” CREEP: Characterization, Damage and Life Assessments, Proc. Fifth Int. Conf. on Creep of Mater., FL (Woodford et al., eds.), pp. 331–339.
7. Itoh, T., Sakane, M., Ohnami, M., and Ameyama, K., 1992b, “Additional Hardening due to Nonproportional Loading,—A Contribution of Stacking Fault Energy,” MECAMAT’92, Proc. Int. Seminar on Multiaxial Plasticity, Cachan, France (Benallal et al., eds.), pp. 43–50.
8. Itoh T. , SakaneM., and OhnamiM., 1994, “High Temperature Multiaxial Low Cycle Fatigue of Cruciform Specimen,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 116, No. 1, pp. 90–98.10.1115/1.2904261 ↗
9. Kanazawa K. , MillerK. J., and BrownM. W., 1979, “Cyclic Deformation of 1% Cr-Mo-V. Steel Under Out-of-Phase Loads,” Fatigue Engineering Materials and Structures, Vol. 2, No. 2, pp. 217–228.10.1111/j.1460-2695.1979.tb01357.x ↗
10. Kitade, M., Ikari, T., Yamauchi, M., and Nakazima, K., 1987, “Cyclic Deformation and Failure of 2 1/4 Cr-1 Mo Steel Under Biaxial Stresses,” Proc. 25th Symp. on Strength of Mater, at High Temp., Soc. Mater. Sci., Japan, pp. 97–101.
11. Krempl E. , and LuH., 1983, “Comparison of the Stress Responses of an Aluminum Alloy Tube to Proportional and Alternate Axial and Shear Strain Paths at Room Temperature,” Mechanics of Materials, Vol. 2, pp. 183–192.10.1016/0167-6636(83)90013-3 ↗
12. Krempl E. , and LuH., 1984, “The Hardening and Rate-Dependent Behavior of Fully Annealed AISI Type 304 Stainless Steel Under Biaxial In-Phase and Out-of-Phase Strain Cycling at Room Temperature,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 106, No. 4, pp. 376–382.10.1115/1.3225733 ↗
13. Liu, K. C, 1991, “A Method Based on Virtual Strain-Energy Parameters for Multiaxial Fatigue Life Prediction,” Advances in Multiaxial Fatigue, ASTM STP, No. 1191, pp. 67–84.(1993).10.1520/STP24796S ↗
14. McDowell, D. L., 1983, “On the Path Dependence of Transient Hardening and Softening to Stable States Under Complex Biaxial Cyclic Loading,” Proc. Int. Conf. on Constitutive Laws for Engng. Mater., Tucson, AZ (Desai and Gallagher, eds.), p. 125.
15. Nishino S. , HamadaN., SakaneM., OhnamiM., MatsumuraN., and TokizaneM., 1986, “Microstructural Study of Cyclic Strain Hardening Behavior in Biaxial Stress State at Elevated Temperature,” Fatigue and Fracture of Engineering Materials and Structures, Vol. 9, No. 1, pp. 65–77.10.1111/j.1460-2695.1986.tb01212.x ↗
16. Nitta A. , OgataT., and KuwabaraK., 1987, “The Effect of Axial-Torsional Strain Phase on Elevated-Temperature Biaxial Low-Cycle Fatigue Life in SUS304 Stainless Steel,” J. Soc. Mater. Sci., Japan, Vol. 36, No. 403, pp. 376–382.10.2472/jsms.36.376 ↗
17. Nitta A. , OgataT., and KuwabaraK., 1988, “Relationship Between Fracture Mode and Fatigue Life under Biaxial Loading at 550°C in SUS304 Stainless Steel,” J. Soc. Mater. Sci., Japan, Vol. 37, No. 414, pp. 334–339.10.2472/jsms.37.334 ↗
18. Nitta A. , OgataT., and KuwabaraK., 1989, “Fracture Modes and Fatigue Life Evaluation of SUS304 Stainless Steel under Non-Proportional Biaxial Loading Condition at 550°C,” J. Soc. Mater. Sci., Japan, Vol. 38, No. 427, pp. 416–422.10.2472/jsms.38.416 ↗
19. Ohnami M. , and HamadaN., 1981, “Crack Propagation Behavior of Biaxial Low-Cycle Fatigue at Elevated Temperature, —Effect of the Cyclic Principal Stressing in Parallel with the Fatigue Crack and the Rotation of the Principal Stress Axes,” J. Soc. Mater. Sci., Japan, Vol. 30, No. 335, pp. 822–828.
20. Ohnami, M., Sakane, M., and Hamada, N., 1985, “Effect of Changing Principal Stress Axes on Low-Cycle Fatigue Life in Various Strain Wave Shapes at Elevated Temperature,” ASTM STP, No. 853, pp. 622–634.10.1520/STP36246S ↗
21. Ohnami M. , SakaneM., and NishinoS., 1988, “Cyclic Behavior of a Type 304 Stainless Steel in Biaxial Stress States at Elevated Temperatures,” International J. Plasticity, Vol. 4, No. 1, pp. 77–89.10.1016/0749-6419(88)90006-X ↗
22. Sakane M. , OhnamiM., and SawadaM., 1987, “Fracture Modes and Low Cycle Fatigue Life in Biaxial Stress State at Elevated Temperature,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 109, No. 3, pp. 236–243.10.1115/1.3225970 ↗
23. Sakane M. , OhnamiM., and SawadaM., 1991, “Biaxial Low Cycle Fatigue of Unaged and Aged 1Cr-1Mo-1/4V Steels at Elevated Temperature,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 113, No. 2, pp. 244–253.10.1115/1.2903399 ↗
24. Smith R. N. , WatsonP., and TopperT. H., 1970, “A Stress Strain Function for the Fatigue of Materials,” J. Materials JMLSA, Vol. 5, No. 4, pp. 767–778.
25. Socie D. F. , 1987, “Multiaxial Fatigue Damage Models,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 109, No. 4, pp. 293–298.10.1115/1.3225980 ↗