journal article·2026-03-08

Influence of cracks on the response characteristics of explosive columns under drop-weight impact

Jun Tao, Xiaoqiang Diao, Xiaofeng Wang, Haichao Ren, Xiaoyang Wu, Yiping Wang

Publisher page

Abstract

To investigate the influence of cracks on the response characteristics of explosive columns under drop-weight impact, a finite element simulation model of a drop-weight impacting an RDX-based aluminized explosive column was established. Columns without cracks, with a close fit, with 1 mm cracks, and with 1.5 mm cracks were prepared, and drop-weight impact loading experiments were conducted. The computational results indicate that the crack edge is the point of maximum stress during drop-weight loading, and the radial displacement of nodes around the crack is significant. Compared to intact and close-fit columns, columns with cracks exhibit a significant increase in the internal maximum stress, stress rate, strain, strain rate, and radial flow velocity, with the magnitude of increase being greater for wider cracks. Drop-weight loading experiments show that the ignition thresholds for aluminized explosive columns under impact are essentially equivalent under no-crack and close-fit conditions. When a crack is present, the ignition threshold under impact significantly decreases. A flow phenomenon of internal material from high-density to low-density regions was observed at the half-radius position along the column axis. The experimental results show good consistency with the simulation results.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Structural Response to Dynamic Loads · High-Velocity Impact and Material Behavior · Cellular and Composite Structures

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Xi’an Modern Chemistry Research Institute

References (24)

Show source-provided references
1. Barry F. 1992. Design modification and calibration of the picatiinny activator for setback safety testing of sadarm. AD–251858.
2. Blumenthal WR, Thompson D, Cady CM, Gray GGT, Idar DJ. 2002. Compressive properties of PBXN-110 and its HTPB based binder as a function of temperature and strain rate. In: 12th international detonation symposium. San Diego, California: Los Alamos National Laboratory. p. 55–60.
3. Dienes JK. 1984. Frictional hot spots and propellant sensitivity. Proceedings of Materials Research Society Symposium; Pittsburgh: Materials Research Society. p. 373–383.
4. Dienes JK. 1996. A unified theory of flow, hot spots, and fragmentation, with an application to explosive sensitivity high pressure shock compression of solids II. p. 366–398. Springer.
5. Dienes JK,Kershner JD. 1998. Multiple-shock initiation via statistical crack mechanics. Proceedings of the 11th Detonation Symposium. Snowmass Village; Colorado: Office of Naval Research. p. 717–724.
6. Dienes JK, Middleditch J, Kershner JD, Zuo Q 2002. Progress in statistical crack mechanics: an approach to initiation. Proceedings of the 12th International Detonation Symposium; San Diego, California: Office of Naval Research. p. 793–799.
7. Duan ZP, et al. 2010. A pore collapse model for hotspot ignition in shocked multi-component explosives. Int J Nonlinear Sci Numer Simul. 11(Supplement):19–24.
8. Gao LL, et al. 2011. Analysis of impact sensitivity characteristics for typical explosive cylinder. Chin J Energetic Mater. 19(4):428–431.
9. Kim K, Sohn CH. 1985. Modeling of reaction buildup processes in shocked porous explosives. In: 8th symposium (international) on detonation. Albuquerque, New Mexico: Naval Surface Weapons Center. p. 926–933.
10. 10.1002/prep.20180002510.1002/prep.201800025 ↗
11. 10.3390/polym1206134210.3390/polym12061342 ↗
12. Liu R, et al. 2021. The role of tension-compression asymmetrical microcrack evolution in the ignition of polymer-bonded explosives under low-velocity impact. J Appl Phys. 129(17):175108.10.1063/5.0046011 ↗
13. 10.1002/prep.20190031310.1002/prep.201900313 ↗
14. Ma X, et al. 2020. Measuring crack growth and rise in temperature around a cylindrical defect in explosive simulants under low-pressure and long-pulse loadings. Propellants, Explos, Pyrotech. 45(10):1654–1661.10.1002/prep.202000057 ↗
15. Ma X, et al. 2022. A modified set of constitutive models for polymer-bonded explosives that consider heterogeneity of initial cracks and failure of damaged granules. Propellants, Explos, Pyrotech. 47(11):e202200032.10.1002/prep.202200032 ↗
16. Myers TF, Hersh KJ. 1982. The effect of base gaps on setback-shock sensiticities of cast composition-B and TNT as determined by the NSWC set back simulator. In: 7th symposium (international) on detonation. Annapolis, Maryland: Naval Surface Weapons Center. p. 926–933.
17. Peng JC, Jiang JW, Liao W. 2020. Bottom temperature simulation of explosive charge in high-speed rotating projectile in internal ballistic process. Acta Armamentarii. 41(9):1783–1791.
18. Sandstrom MW, et al. 2015. Variation of methods in small-scale safety and thermal testing of improvised explosives. Propellants Explos Pyrotech. 40(1):109–126.10.1002/prep.201400108 ↗
19. Teng WT. 2013. Study on launch safety of thermobaric explosive. Nanjing University of Science and Technology.
20. Williamson DM, Dordge D, Cullis I GI, Gould PJ, Church PD 2010. Towards a fundamental understanding of the thermomechanical response of damaged polymer bonded energetic materials. In: 14th international detonation symposium. Coeur d’Alene, Idaho: U.S. Department of Energy (DOE); p. 1285–1294.
21. 10.1016/j.mechmat.2011.08.00410.1016/j.mechmat.2011.08.004 ↗
22. Yang JG, Yu YG. 2008. Velocity prediction of big caliber gun based on traveling charge scheme. Exp Shock Waves. 28(2):161–165.
23. Yun LF, et al. 2010. Application of DCD scheme to computation of two-phase flow interior ballistics for fractured propellant bed. Exp Shock Waves. 30(3):295–300.
24. Zhang WH, Yu YG. 2023. Analysis of gas-eroding barrel characteristics based on fluid-solid interaction. Exp Shock Waves. 43(3):034201.