journal article·2014-03-21

Indirect three-dimensional printing of synthetic polymer scaffold based on thermal molding process

Jeong Hun Park, Jin Woo Jung, Hyun-Wook Kang, Dong-Woo Cho

Biofabrication· Volume 6· Issue 2
Publisher page

Abstract

One of the major issues in tissue engineering has been the development of three-dimensional (3D) scaffolds, which serve as a structural template for cell growth and extracellular matrix formation. In scaffold-based tissue engineering, 3D printing (3DP) technology has been successfully applied for the fabrication of complex 3D scaffolds by using both direct and indirect techniques. In principle, direct 3DP techniques rely on the straightforward utilization of the final scaffold materials during the actual scaffold fabrication process. In contrast, indirect 3DP techniques use a negative mold based on a scaffold design, to which the desired biomaterial is cast and then sacrificed to obtain the final scaffold. Such indirect 3DP techniques generally impose a solvent-based process for scaffold fabrication, resulting in a considerable increase in the fabrication time and poor mechanical properties. In addition, the internal architecture of the resulting scaffold is affected by the properties of the biomaterial solution. In this study, we propose an advanced indirect 3DP technique using projection-based micro-stereolithography and an injection molding system (IMS) in order to address these challenges. The scaffold was fabricated by a thermal molding process using IMS to overcome the limitation of the solvent-based molding process in indirect 3DP techniques. The results indicate that the thermal molding process using an IMS has achieved a substantial reduction in scaffold fabrication time and has also provided the scaffold with higher mechanical modulus and strength. In addition, cell adhesion and proliferation studies have indicated no significant difference in cell activity between the scaffolds prepared by solvent-based and thermal molding processes.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · 3D Printing in Biomedical Research · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. 10.1007/s12541-012-0057-810.1007/s12541-012-0057-8 ↗
2. 10.1016/j.tibtech.2004.05.00510.1016/j.tibtech.2004.05.005 ↗
3. 10.1039/c1sm06863f10.1039/c1sm06863f ↗
4. 10.1016/j.tibtech.2004.10.00410.1016/j.tibtech.2004.10.004 ↗
5. 10.1038/nmat142110.1038/nmat1421 ↗
6. 10.1016/j.biomaterials.2010.04.05010.1016/j.biomaterials.2010.04.050 ↗
7. 10.1016/j.biomaterials.2007.08.01810.1016/j.biomaterials.2007.08.018 ↗
8. Shor L · Biofabrication · 2009 · 110.1088/1758-5082/1/1/015003 ↗
9. Kolan K C R · Biofabrication · 2011 · 3
10. 10.1002/jbm.b.3097510.1002/jbm.b.30975 ↗
11. 10.1016/S0142-9612(02)00276-410.1016/S0142-9612(02)00276-4 ↗
12. 10.1016/j.biomaterials.2004.10.04010.1016/j.biomaterials.2004.10.040 ↗
13. 10.1007/s10856-010-4166-610.1007/s10856-010-4166-6 ↗
14. 10.1089/ten.tec.2011.062110.1089/ten.tec.2011.0621 ↗
15. Park J H · Biofabrication · 2012 · 4
16. 10.1007/s13770-013-0358-810.1007/s13770-013-0358-8 ↗
17. 10.1002/jbm.a.3414910.1002/jbm.a.34149 ↗
18. 10.1021/je050260210.1021/je0502602 ↗
19. 10.1016/j.sna.2012.01.01610.1016/j.sna.2012.01.016 ↗
20. Arya R K · Int. J. Sci. Tech. Res. · 2012 · 1 · 48
21. 10.1016/S0376-7388(02)00119-910.1016/S0376-7388(02)00119-9 ↗
22. 10.1016/j.biomaterials.2006.12.02310.1016/j.biomaterials.2006.12.023 ↗
23. 10.1002/app.2014410.1002/app.20144 ↗
24. 10.1016/j.biomaterials.2006.05.02710.1016/j.biomaterials.2006.05.027 ↗