HIGH-SPEED VIDEO IMAGE ANALYSIS OF LIQUID METAL ATOMIZATION PROCESS
Source abstract
Abstract
Gas-assisted atomization is used to produce metal powders for additive manufacturing. In these systems the primary atomization governs the powder size distribution, but it is experimentally challenging to investigate. In this study, the primary atomization of a molten metal spray was monitored with a calibrated high-speed camera and digital image processing. The technique enabled the generation of spatio-temporal maps at different distances from the nozzle. Among the characteristics of the spray, mean values and standard deviation of the spray width along the spraying direction, and the frequency of the oscillation of the spray boundaries are presented. Statistically relevant spray asymmetries were identified, which can be caused by faulty spray operation in form of a localized metal solidification at the pouring nozzle. By systematically varying the gas temperature and the gas atomization pressure, it is shown that heating of the gas up to 573 K stabilizes the spraying process and enhances the liquid dispersion in the recirculation zone.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fluid Dynamics and Heat Transfer · Additive Manufacturing and 3D Printing Technologies · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Anderson, I.E. and Achelis, L., Two Fluid Atomization Fundamentals, in Metal Sprays and Spray Deposition, H. Henein, V. Uhlenwinkel, and U. Fritsching, Eds., Cham: Springer International Publishing, pp. 49-88, 2017.10.1007/978-3-319-52689-8_3 ↗
2. Anderson, I.E., Rieken, J., Meyer, J.L.L., Byrd, D., and Heidloff, A.J., Visualization of Atomization Gas Flow and Melt Break-Up Effects in Response to Nozzle Design, USDOE Office of Science, Tech. Rep. IS-M 962, TRN: US201119%%515, 2011.
3. Anderson, J.J.D., Fundamentals of Aerodynamics, New York: McGraw-Hill Education, 2011.
4. Antipas, G.S.E., Review of Gas Atomisation and Spray Forming Phenomenology, Powder Metall., vol. 56, no. 4, pp. 317-30, 2013. DOI: 10.1179/1743290113Y.000000005710.1179/1743290113Y.0000000057 ↗
5. Ciftci, N., Ellendt, N., Soares Barreto, E., Mädler, L., and Uhlenwinkel, V., Increasing the Amorphous Yield of {(Fe0.6Co0.4)0.75B0.2Si0.05}96Nb4 Powders by Hot Gas Atomization, Adv. Powder Technol., vol. 29, no. 2, pp. 380-85, 2018. DOI: 10.1016/j.apt.2017.11.02510.1016/j.apt.2017.11.025 ↗
6. Czisch, C. and Fritsching, U., Atomizer Design for Viscous-Melt Atomization, Mater. Sci. Eng.: A, vol. 477, no. 1, pp. 21-25, 2008. DOI: 10.1016/j.msea.2007.06.08710.1016/j.msea.2007.06.087 ↗
7. Delacourt, E., Desmet, B., and Besson, B., Characterisation of Very High Pressure Diesel Sprays Using Digital Imaging Techniques, Fuel, vol. 84, no. 7, pp. 859-67, 2005. DOI: 10.1016/j.fuel.2004. 12.00310.1016/j.fuel.2004.12.003 ↗
8. Ding, H., Wang, Z., Li, Y., Xu, H., and Zuo, C., Initial Dynamic Development of Fuel Spray Analyzed by Ultra High Speed Imaging, Fuel, vol. 169, pp. 99-110, 2016. DOI: 10.1016/j.fuel.2015.11.08310.1016/j.fuel.2015.11.083 ↗
9. Fritsching, U., Spray Simulation: Modeling and Numerical Simulation of Sprayforming Metals, Cambridge, UK: Cambridge University Press, 2004.10.1017/CBO9780511536649 ↗
10. Goo Kim, I. and Young Lee, S., A Simple Technique for Sizing and Counting Spray Drops Using Digital Image Processing, Exp. Therm. Fluid Sci., vol. 3, no. 2, pp. 214-21, 1990. DOI: 10.1016/0894-1777(90)90089-P10.1016/0894-1777(90)90089-P ↗
11. Guo, J.-P., Wang, Y.-B., Bai, F.-Q., Zhang, F., and Du, Q., Effects of Asymmetric Gas Distribution on the Instability of a Plane Power-Law Liquid Jet, Energies, vol. 11, no. 7, 2018. DOI: 10.3390/en1107185410.3390/en11071854 ↗
12. Heindel, T., 1. X-Ray Imaging Techniques to Quantify Spray Characteristics in the near Field, Atomiz. Sprays, vol. 28, no. 11, pp. 1029-59, 2018. DOI: 10.1615/AtomizSpr.201902879710.1615/AtomizSpr.2019028797 ↗
13. Hussain, S., Cui, C., He, L., Madler, L., and Uhlenwinkel, V., Effect of Hot Gas Atomization on Spray Forming of Steel Tubes Using a Close-Coupled Atomizer (CCA), J. Mater. Process. Technol., vol. 282, p. 116677, 2020. DOI: 10.1016/j.jmatprotec.2020.11667710.1016/j.jmatprotec.2020.116677 ↗
14. Iida, T. and Guthrie, R.I.L., The Physical Properties of Liquid Metals, Oxford, UK: Oxford University Press, pp. 1-312, 1988.
15. Lee, Z., Eichner, D., Tennis, J., Ryan, M., Sowell, T., Benson, M., Poppel, B., Nelson, T., Guzman, P., Fahrig, R., Eaton, J., Kurman, M., and Kweon, C., A Comparison of Shadowgraphy and X-Ray Computed Tomography in Liquid Spray Analysis, ASME Int. Mechanical Engineering Congress and Exposition, Proc. (IMECE), vol. 7, 2014. DOI: 10.1115/IMECE2014-3877010.1115/IMECE2014-38770 ↗
16. Leroux, B., Delabroy, O., and Lacas, F., Experimental Study of Coaxial Atomizers Scaling. Part I: Dense Core Zone, Atomiz. Sprays, vol. 17, pp. 381-407, 2007. DOI: 10.1615/AtomizSpr.v17.i5.1010.1615/AtomizSpr.v17.i5.10 ↗
17. Mates, S. and Settles, G., A Study of Liquid Metal Atomization Using Close-Coupled Nozzles, Part 2: Atomization Behavior, Atomiz. Sprays, vol. 15, pp. 41-60, 2005. DOI: 10.1615/AtomizSpr.v15.i1.3010.1615/AtomizSpr.v15.i1.30 ↗
18. McCarthy, I.N., Adkins, N.J., Aslam, Z., Mullis, A.M., and Cochrane, R.F., High Speed Imaging and Fourier Analysis of the Melt Plume during Close Coupled Gas Atomisation, Powder Metall., vol. 52, no. 3, pp. 205-12, 2009. DOI: 10.1179/174329409X40954910.1179/174329409X409549 ↗
19. Motaman, S., Mullis, A.M., Cochrane, R.F., and Borman, D.J., Numerical and Experimental Investigations of the Effect of Melt Delivery Nozzle Design on the Open- to Closed-Wake Transition in Closed-Coupled Gas Atomization, Metallurg. Mater. Trans. B, vol. 46, no. 4, pp. 1990-2004, 2015. DOI: 10.1007/s11663-015-0346-610.1007/s11663-015-0346-6 ↗
20. Mullis, A.M., McCarthy, I.N., and Cochrane, R.F., High Speed Imaging of the Flow during Close-Coupled Gas Atomisation: Effect of Melt Delivery Nozzle Geometry, J. Mater. Process. Technol., vol. 211, pp. 1471-77, 2011.10.1016/j.jmatprotec.2011.03.020 ↗
21. Sato, Y., Representation of the Viscosity of Molten Alloy as a Function of the Composition and Temperature, Jpn. J. Appl. Phys., vol. 50, no. 11S, p. 11RD01, 2011. DOI: 10.1143/JJAP.50.11RD0110.7567/JJAP.50.11RD01 ↗
22. Schwenck, D., Ellendt, N., Fischer-Buhner, J., Hofmann, P., and Uhlenwinkel, V., A Novel Convergent-Divergent Annular Nozzle Design for Close-Coupled Atomisation, Powder Metall., vol. 60, no. 3, pp. 198-207, 2017. DOI: 10.1080/00325899.2017.129109810.1080/00325899.2017.1291098 ↗
23. Strang, G., Computational Science and Engineering, Cambridge, MA: Wellesley-Cambridge Press, 2007.
24. Tian, X.-S., Zhao, H., Liu, H.-F., Li, W.-F., and Xu, J.-L., Effect of Central Tube Thickness on Wave Frequency of Coaxial Liquid Jet, Fuel Process. Technol., vol. 119, pp. 190-97, 2014. DOI: 10.1016/j. fuproc.2013.11.01110.1016/j.fuproc.2013.11.011 ↗
25. Ting, J. and Anderson, I. E., A Computational Fluid Dynamics (CFD) Investigation of the Wake Closure Phenomenon, Mater. Sci. Eng.: A, vol. 379, no. 1, pp. 264-76, 2004. DOI: 10.1016/j.msea.2004.02.06510.1016/j.msea.2004.02.065 ↗
26. Ting, J., Connor, J., and Ridder, S., High-Speed Cinematography of Gas-Metal Atomization, Mater. Sci. Eng.: A, vol. 390, no. 1, pp. 452-60, 2005. DOI: 10.1016/j.msea.2004.08.06010.1016/j.msea.2004.08.060 ↗
27. Ting, J., Peretti, M.W., and Eisen, W.B., The Effect of Wake-Closure Phenomenon on Gas Atomization Performance, Mater. Sci. Eng.: A, vol. 326, no. 1, pp. 110-21, 2002. DOI: 10.1016/S0921-5093(01)01437-X10.1016/S0921-5093(01)01437-X ↗
28. Tropea, C., Optical Particle Characterization in Flows, Ann. Rev. Fluid Mech., vol. 43, no. 1, pp. 399-426, 2011. DOI: 10.1146/annurev-fluid-122109-16072110.1146/annurev-fluid-122109-160721 ↗
29. Tsai, R., A Versatile Camera Calibration Technique for High-Accuracy 3D Machine Vision Metrology Using Off-the-Shelf TV Cameras and Lenses, IEEE J. Robot. Auto., vol. 3, no. 4, pp. 323-44, 1987. DOI: 10.1109/JRA.1987.108710910.1109/JRA.1987.1087109 ↗
30. Urionabarrenetxea, E., MartÃn, J.M., Avello, A., and Rivas, A., Simulation and Validation of the Gas Flow in Close-Coupled Gas Atomisation Process: Influence of the Inlet Gas Pressure and the Throat Width of the Supersonic Gas Nozzle, Powder Technol., vol. 407, p. 117688, 2022. DOI: 10.1016/j.powtec. 2022.11768810.1016/j.powtec.2022.117688 ↗
31. Vafadar, A., Guzzomi, F., Rassau, A., and Hayward, K., Advances in Metal Additive Manufacturing: A Review of Common Processes, Industrial Applications, and Current Challenges, Appl. Sci., vol. 11, no. 3, 2021. DOI: 10.3390/app1103121310.3390/app11031213 ↗
32. Zhang, Z., A Flexible New Technique for Camera Calibration, IEEE Trans. Pattern Anal. Mach. Intel., vol. 22, pp. 1330-34, 2000.10.1109/34.888718 ↗
33. Zhou, W., Hu, J., Feng, M., Yang, B., and Cai, X., Study on Imaging Method for Measuring Droplet Size in Large Sprays, Particuology, vol. 22, pp. 100-106, 2015. DOI: 10.1016/j.partic.2014.12.00310.1016/j.partic.2014.12.003 ↗
34. Zocca, A., Franchin, G., Colombo, P., and Gunster, J., Additive Manufacturing, in Encyclopedia of Materials: Technical Ceramics and Glasses, M. Pomeroy, Ed., Oxford: Elsevier, pp. 203-21, 2021.10.1016/B978-0-12-803581-8.12081-8 ↗