ASYMMETRIC BREAKUP OF ANNULAR LIQUID SHEETS IN LIQUID-CENTERED SWIRL COAXIAL INJECTORS
Source abstract
Abstract
Cryogenic rocket engines use swirl coaxial injectors due to their consistent spray characteristics over a wide range of operating conditions. Axisymmetric liquid sheets are formed in liquid-centred swirl coaxial injectors of cryogenic engines at their nominal operating conditions. The azimuthal uniformity of the spray formed in this type of injector depends on the swirler configuration and geometry of the flow passages. The liquid sheet breaks into ligaments and then into multitude of droplets due to aerodynamic interaction of the liquid sheet with the surrounding gas. The inner and outer swirl injectors are cold flow characterized using water and nitrogen gas, respectively. Asymmetric breakup of conical liquid sheets was investigated at different gas Weber numbers using flow visualization techniques. Azimuthal uniformity of the spray was determined from the measurements of mechanical patternator. It is of paramount importance to determine the effect of gas swirl on spray uniformity of liquid-centered swirl coaxial injector for different gas-to-liquid mass ratios. It was observed that swirl in the co-flowing gas reduces the inherent asymmetry of the liquid sheet.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fluid Dynamics and Heat Transfer · Electrohydrodynamics and Fluid Dynamics · Cyclone Separators and Fluid Dynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Bai, X., Cheng, P., Sheng, L., Li, Q., Zhang, X., and Kang, Z., Effects of Backpressure on Self-Pulsation Characteristics of Liquid-Centered Swirl Coaxial Injectors, Int. J. Multiphase Flow, vol. 116, pp. 239-249, 2019.10.1016/j.ijmultiphaseflow.2019.04.017 ↗
2. Bai, X., Li, Q., Cheng, P., Sheng, L., and Kang, Z., Investigation of Self-Pulsation Characteristics for a Liquid-Centered Swirl Coaxial Injector with Recess, Acta Astronaut., vol. 151, pp. 511-521, 2018.10.1016/j.actaastro.2018.07.002 ↗
3. Benjamin, M.A., Jensen, R.J., and Arienti, M., Review of Atomization: Current Knowledge and Future Requirements for Propulsion Combustors, Atomization Sprays, vol. 20, pp. 485-512, 2010.10.1615/AtomizSpr.v20.i6.20 ↗
4. Betelin, V.B., Smirnov, N.N., Nikitin, V.F., Dushin, V.R., Kushnirenko, A.G., and Nerchenko, V.A., Evaporation and Ignition of Droplets in Combustion Chambers Modeling and Simulation, Acta Astronaut., vol. 70, pp. 23-35, 2012.10.1016/j.actaastro.2011.06.021 ↗
5. Canny, J., A Computational Approach to Edge Detection, IEEE Trans. Pattern Anal. Mach. Intel., vol. PAMI-8, pp. 679-698, 1986.10.1109/TPAMI.1986.4767851 ↗
6. Dombrowski, N. and Foumeny, E.A., On the Stability of Liquid Sheets in Hot Atmospheres, Atomization Sprays, vol. 8, pp. 235-240, 1998.10.1615/AtomizSpr.v8.i2.60 ↗
7. Fraser, R.P., Dombrowski, N., and Routley, J.H., The Atomization of a Liquid Sheet by an Impinging Air Stream, Chem. Eng. Sci., vol. 18, pp. 339-353, 1963.10.1016/0009-2509(63)80027-5 ↗
8. Im, J.H., Cho, S., Yoon, Y., and Moon, I., Comparative Study of Spray Characteristics of Gas-Centered and Liquid-Centered Swirl Coaxial Injectors, J. Propul. Power, vol. 26, pp. 1196-1204, 2010.10.2514/1.48436 ↗
9. Im, J.H., Kim, D., Han, P., Yoon, Y., and Bazarov, V., Self-Pulsation Characteristics of a Gas-Liquid Swirl Coaxial Injector, Atomization Sprays, vol. 19, pp. 57-74, 2009.10.1615/AtomizSpr.v19.i1.40 ↗
10. Inamura, T., Tamura, H., and Sakamoto, H., Characteristics of Liquid Film and Spray Injected from Swirl Coaxial Injector, J. Propul. Power, vol. 19, pp. 632-639, 2012.10.2514/2.6151 ↗
11. Jeong, S., Bae, J., Yoon, S.S., and Yoon, Y., Effect of Self-Excited Instability on Single Liquid Swirl Injector Flow Characteristics, Acta Astronaut., vol. 178, pp. 452-462, 2021.10.1016/j.actaastro.2020.08.029 ↗
12. Jo, H., Jeong, G., Bae, J., and Yoon, Y., Dynamic Behavior of Jet-Swirl Spray under Resonance Condition with External Excitation, Acta Astronaut., vol. 189, pp. 298-309, 2021.10.1016/j.actaastro.2021.08.037 ↗
13. Kang, Z., Li, Q., Cheng, P., Zhang, X., andWang, Z., Effects of Recess on the Self-Pulsation Characteristics of Liquid-Centered Swirl Coaxial Injectors, J. Propul. Power, vol. 32, pp. 1124-1132, 2016.10.2514/1.B35632 ↗
14. Kang, Z., Li, Q., Zhang, J., and Cheng, P., Effects of Gas Liquid Ratio on the Atomization Characteristics of Gas-Liquid Swirl Coaxial Injectors, Acta Astronaut., vol. 146, pp. 24-32, 2018.10.1016/j.actaastro.2018.02.026 ↗
15. Kim, D., Han, P., Im, J.H., Yoon, Y., and Bazarov, V.G., Effect of Recess on the Spray Characteristics of Liquid-Liquid Swirl Coaxial Injectors, J. Propul. Power, vol. 23, pp. 1194-1203, 2012.10.2514/1.30450 ↗
16. Kim, D., Kim, S., Han, P., and Yoon, Y., Effect of Recess on Mixing and Atomization Characteristics of Liquid-Liquid Swirl Coaxial Injectors, Atomization Sprays, vol. 20, pp. 41-55, 2010.10.1615/AtomizSpr.v20.i1.40 ↗
17. Kim, S., Yoon, J., and Yoon, Y., Internal Flow Characteristics of Liquid-Liquid Swirl Coaxial Injectors with Different Recess Lengths and Oxidizer-Fuel Ratios, Atomization Sprays, vol. 21, pp. 971-987, 2011.10.1615/AtomizSpr.2012003917 ↗
18. Lee, S., Koo, J., and Yoon, Y., Effects of Skip Distance on the Spray Characteristics of a Pintle Injector, Acta Astronaut., vol. 178, pp. 471-480, 2021.10.1016/j.actaastro.2020.09.043 ↗
19. Li, Q., Kang, Z., Zhang, X., and Cheng, P., Effect of Recess Length on the Spray Characteristics of Liquid-Centered Swirl Coaxial Injectors, Atomization Sprays, vol. 26, pp. 535-550, 2016.10.1615/AtomizSpr.2015011831 ↗
20. Liu, C., Liu, F., Yang, J., Mu, Y., Hu, C., and Xu, G., Experimental Investigations of Spray Generated by a Pressure Swirl Atomizer, J. Energy Inst., vol. 92, pp. 210-221, 2019.10.1016/j.joei.2018.01.014 ↗
21. Liu, J., Zhang, X.Q., Li, Q.L., and Wang, Z.G., Effect of Geometric Parameters on the Spray Cone Angle in the Pressure Swirl Injector, J. Aerospace Eng., vol. 227, pp. 342-353, 2012.10.1177/0954410011432233 ↗
22. Lux, J., Suslov, D., Bechle, M., Oschwald, M., and Haidn, O., Investigation of Sub- and Supercritical LOX/Methane Injection Using Optical Diagnostics, AIAA/ASME/SAE/ASEE 42nd Joint Propulsion Conf., Vol. 9, Sacramento, CA, pp. 7259-7269, 2006.10.2514/6.2006-5077 ↗
23. Nath, S., Mukhopadhyay, A., Datta, A., Sen, S., and Tharakan, T.J., Influence of Gas Velocity on Breakup of Planar Liquid Sheets Sandwiched between Two Gas Streams, Atomization Sprays, vol. 20, pp. 983-1003, 2010.10.1615/AtomizSpr.v20.i11.50 ↗
24. Rahman, S.A., Pal, S., and Santoro, R.J., Swirl Coaxial Atomization: Cold-Flow and Hot-Fire Experiments, 33rd Aerospace Sciences Meeting and Exhibit, Reno, NV, 1995.10.2514/6.1995-381 ↗
25. Ramamurthi, K. and Patnaik, R., Uniformity of Swirled Sprays Formed with Nozzles of Varying Surface Roughness, Atomization Sprays, vol. 9, pp. 483-496, 1999.10.1615/AtomizSpr.v9.i5.30 ↗
26. Ramamurthi, K. and Tharakan, T.J., Experimental Study of Liquid Sheets Formed in Coaxial Swirl Injectors, J. Propul. Power, vol. 11, pp. 1103-1109, 1995.10.2514/3.23947 ↗
27. Ramamurthi, K. and Tharakan, T.J., Flow Transition in Swirled Liquid Sheets, AIAA J., vol. 36, pp. 420-427, 1998.10.2514/3.13837 ↗
28. Rizk, N. and Lefebvre, A., Internal Flow Characteristics of Simplex Swirl Atomizers, J. Propul. Power, vol. 1, pp. 193-199, 2012.10.2514/3.22780 ↗
29. Sanchez, L.E., Ellis, R., Dorado, V., and Choudhuri, A., An Experimental Study of the Effects of Plate Geometry on the Spray Atomization of LOX/CH4 in Uni-Element Shear Coaxial Injectors, 50th AIAA/ASME/SAE/ASEE Joint Propulsion Conf., Cleveland, OH, 2014.10.2514/6.2014-3788 ↗
30. Scheer, I.W. and Beaumont, C., A New Quality Methodology and Metrics for Spray Pattern Analysis, Atomization Sprays, vol. 21, pp. 189-202, 2011.10.1615/AtomizSpr.2011002806 ↗
31. Siddharth, K.S., Panchagnula, M.V., and Tharakan, T.J., Feature Correlation Velocimetry for Measuring Instantaneous Liquid Sheet Velocity, J. Fluids Eng. Trans. ASME, vol. 139, p. 091401, 2017.10.1115/1.4036593 ↗
32. Smirnov, N.N., Betelin, V.B., Kushnirenko, A.G., Nikitin, V.F., Dushin, V.R., and Nerchenko, V.A., Ignition of Fuel Sprays by Shock Wave Mathematical Modeling and Numerical Simulation, Acta Astronaut., vol. 87, pp. 14-29, 2013.10.1016/j.actaastro.2013.01.023 ↗
33. Smirnov, N.N., Nikitin, V.F., Dushin, V.R., Filippov, Y.G., Nerchenko, V.A., and Khadem, J., Combustion Onset in Non-Uniform Dispersed Mixtures, Acta Astronaut., vol. 115, pp. 94-101, 2015.10.1016/j.actaastro.2015.04.021 ↗
34. Song, W., Cha, J., Yoon, Y., and Koo, J., Comparison of Blockage Performance of Pressure Wave in Structural Baffle Injector and Fluidic Baffle Injector, Acta Astronaut., vol. 176, pp. 666-671, 2020.10.1016/j.actaastro.2020.04.053 ↗
35. Song,W., Lee, J., and Koo, J., Study on the Damping Capacity of a Fluidic Baffle under Different Injection Conditions, Acta Astronaut., vol. 163, pp. 189-195, 2019.10.1016/j.actaastro.2019.03.026 ↗
36. Tharakan, T.J., Mukhopadhyay, A., Datta, A., and Jog, M.A., Trends in Comprehensive Modeling of Spray Formation, Int. J. Spray Combust. Dyn., vol. 5, pp. 123-180, 2013.10.1260/1756-8277.5.2.123 ↗
37. Tharakan, T.J. and Ramamurthi, K., Growth of Longitudinal Waves in Plane Liquid Sheets Having Lateral Wave Modes when Exposed to Two Gas Streams of Unequal Velocities, Atomization Sprays, vol. 15, pp. 181-200, 2005.10.1615/AtomizSpr.v15.i2.50 ↗
38. Tharakan, T.J. and Sreejith, T.S., Effect of Surface Roughness of Converging End on Flow and Spray Characteristics of a Swirl Injector, Int. J. Fluid Mech. Res., vol. 52, pp. 1-15, 2025.10.1615/InterJFluidMechRes.2024052348 ↗
39. Tyurenkova, V.V., Smirnova, M.N., Stamov, L.I., and Smirnov, N.N., Mathematical Modeling of Droplet Collisions in Sprays under Microgravity Conditions, Acta Astronaut., vol. 219, pp. 459-466, 2024.10.1016/j.actaastro.2024.03.036 ↗
40. Wang, X.F. and Lefebvre, A.H., Mean Drop Sizes from Pressure-Swirl Nozzles, J. Propul. Power, vol. 3, pp. 11-18, 2012.10.2514/3.22946 ↗
41. Zhang, T., Dong, B., Chen, X., Qiu, Z., Jiang, R., and Li, W., Spray Characteristics of Pressure-Swirl Nozzles at Different Nozzle Diameters, Appl. Therm. Eng., vol. 121, pp. 984-991, 2017.10.1016/j.applthermaleng.2017.04.089 ↗