journal article·2022

MACROSCOPIC AND MICROSCOPIC CHARACTERISTICS OF A SINGLE-HOLE SPRAY UNDER LOW AMBIENT PRESSURE INDUCED CONDITIONS

Hongliang Luo, Gengxin Zhang, Panpan Dong, Keiya Nishida

Atomization and Sprays· Volume 32· Issue 8
Publisher page

Abstract

Flash boiling spray is a promising method to improve atomization, which subsequently affects the combustion phenomenon in engines. Therefore, an investigation on both macroscopic and microscopic characteristics of the flash boiling spray should be done to understand this behavior and mechanism. A mini-sac injector with a single hole was used under different injection pressures among 10, 15, and 20 MPa. Experiments were performed in a constant volume chamber with low ambient pressures varying from 5 to 100 kPa. First, macroscopic behaviors including morphology, spray tip penetration, spray angle, and spray cone angle were compared by a Mie scattering method. Then, microscopic characteristics of flash boiling spray were obtained with the help of particle image analysis technology. In order to analyze the droplet behaviors along the spray axis completely, a spray "slicer" was introduced to filter the spray. The influences of measurement location, injection pressure, and ambient pressure were discussed in detail. Results showed that although the injection pressure and measurement location have influences on the spray and atomization in both macroscopic and microscopic cases, the ambient pressure plays a more critical effect on it, indicating the low ambient pressure-induced flash boiling spray could improve the atomization much more efficiently.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Combustion Engine Technologies · Fluid Dynamics and Heat Transfer · Combustion and flame dynamics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Aleiferis, P.G. and Van Romunde, Z.J.F., An Analysis of Spray Development with Iso-Octane, n-Pentane, Gasoline, Ethanol and n-Butanol from a Multi-Hole Injector under Hot Fuel Conditions, Fuel, vol. 105, pp. 143-168, 2013.10.1016/j.fuel.2012.07.044 ↗
2. Badawy, T., Xu, H., and Li, Y., Macroscopic Spray Characteristics of Iso-Octane, Ethanol, Gasoline and Methanol from a Multi-Hole Injector under Flash Boiling Conditions, Fuel, vol. 307, p. 121820, 2022.
3. Brown, R. and York, L.J., Sprays Formed by Flashing Liquid Jets, AIChE J., vol. 8, no. 2, pp. 149-153, 1962.10.1002/aic.690080204 ↗
4. Chang, M., Park, J., Kim, H.I., and Park, S., Comparison of Spray Evaporation Characteristics of Five-Hole GDI Injectors with Different Hole Arrangements under Flash Boiling Conditions, Int. J. Heat Mass Transf., vol. 181, p. 121841, 2021.
5. Chen, H., Hung, D. L., Xu, M., and Zhong, J., A Dynamic Thresholding Technique for Extracting the Automotive Spark-Ignition Direct-Injection Pulsing Spray Characteristics, J. Vis., vol. 17, no. 3, pp. 197-209, 2014.10.1007/s12650-014-0203-8 ↗
6. Gemci, T., Yakut, K., Chigier, N., and Ho, T., Experimental Study of Flash Atomization of Binary Hydrocarbon Liquids, Int. J. Multiphase Flow, vol. 30, no. 4, pp. 395-417, 2004.10.1016/j.ijmultiphaseflow.2003.12.003 ↗
7. Guo, H., Ma, X., Li, Y., Liang, S., Wang, Z., Xu, H., and Wang, J., Effect of Flash Boiling on Microscopic and Macroscopic Spray Characteristics in Optical GDI Engine, Fuel, vol. 190, pp. 79-89, 2017.10.1016/j.fuel.2016.11.043 ↗
8. He, X., Li, Y., Liu, C., Sjberg, M., Vuilleumier, D., Liu, F., and Yang, Q., Characteristics of Spray and Wall Wetting under Flash-Boiling and Non-Flashing Conditions at Varying Ambient Pressures, Fuel, vol. 264, p. 116683, 202010.1016/j.fuel.2019.116683 ↗
9. Hung, D.L., Harrington, D.L., Gandhi, A.H., Markle, L.E., Parrish, S.E., Shakal, J.S., Sayar, H., Cummings, S.D., and Kramer, J.L., Gasoline Fuel Injector Spray Measurement and Characterization-A New SAE J2715 Recommended Practice, SAE Int. J. Fuels Lubricants, vol. 1, no. 1, pp. 534-548, 2009.10.4271/2008-01-1068 ↗
10. Lacey, J., Poursadegh, F., Brear, M.J., Gordon, R., Petersen, P., Lakey, C., Butcher, B., and Ryan, S., Generalizing the Behavior of Flash-Boiling, Plume Interaction and Spray Collapse for Multi-Hole, Direct Injection, Fuel, vol. 200, pp. 345-356, 2017.10.1016/j.fuel.2017.03.057 ↗
11. Li, X., Yang, S., Qiu, S., Li, T., and Xu, M., Investigation on Flash Boiling Spray Fluctuations in the Near-Field and Far-Field under Gasoline Direct Injection Related Conditions, Appl. Therm. Eng., vol. 179, p. 115655, 2020.
12. Liu, W., Lu, Y., Kang, Y., Yan, J., and Lee, C.F., Macroscopic Characteristics of Flash-Boiling Spray Focused on Plume Interaction, Int. J. Heat Mass Transf., vol. 170, p. 120999, 2021.
13. Luo, H., Uchitomi, S., Nishida, K., Ogata, Y., Zhang, W., and Fujikawa, T., Experimental Investigation on Fuel Film Formation by Spray Impingement on Flat Walls with Different Surface Roughness, Atomization Sprays, vol. 27, no. 7, pp. 611-628, 2017.10.1615/AtomizSpr.2017019706 ↗
14. Luo, H., Nishida, K., Uchitomi, S., Ogata, Y., Zhang, W., and Fujikawa, T., Microscopic Behavior of Spray Droplets under Flat-Wall Impinging Condition, Fuel, vol. 219, pp. 467-476, 2018.10.1016/j.fuel.2018.01.059 ↗
15. Luo, H., Jin, Y., Nishida, K., Ogata, Y., Yao, J., and Chen, R., Microscopic Characteristics of Impinging Spray Sliced by a Cone Structure under Increased Injection Pressures, Fuel, vol. 284, p. 119033, 2021a.10.1016/j.fuel.2020.119033 ↗
16. Luo, H., Chang, F., Zhan, C., Nishida, K., Ogata, Y., Zhang, J., Yao, J., Kong, X., and Zhu, J., Microscopic Characteristics of Multiple Droplets Behaviors at the Near-Wall Region during the Quasi-Steady State, Fuel, vol. 286, p. 119431, 2021b.10.1016/j.fuel.2020.119431 ↗
17. Naber, J.D. and Siebers, D.L., Effects of Gas Density and Vaporization on Penetration and Dispersion of Diesel Sprays, SAE Trans., pp. 82-111, 1996.10.4271/960034 ↗
18. Qiu, S., Xiao, D., Zhang, X., Wang, S., Wang, T., Li, X., and Xu, M., Experimental Investigations of the Phase Change Impacts on Flash Boiling Spray Propagations and Impingements, Fuel, vol. 312, p. 122871, 2022.
19. Schulz, F. and Beyrau, F., The Influence of Flash-Boiling on Spray-Targeting and Fuel Film Formation, Fuel, vol. 208, pp. 587-594, 2017.10.1016/j.fuel.2017.07.047 ↗
20. Smith, S.W., The Scientist and Engineer's Guide to Digital Signal Processing, San Diego, CA: California Technical Publishing, 1997.
21. Sun, Z., Wang, H., Cui, M., Nour, M., Li, X., and Xu, M., Investigation of Flash Boiling Injection Schemes in Lean-Burn Gasoline Direct Injection Engines, Appl. Energy Combust. Sci., vol. 7, p. 100035, 2021a.10.1016/j.jaecs.2021.100035 ↗
22. Sun, Z., Cui, M., Nour, M., Li, X., Hung, D., and Xu, M., Differences in Pool-Fire Induced Soot Production between Subcooled Spray and Flash Boiling Spray in a DISI Engine, Fuel, vol. 287, p. 119453, 2021b.10.1016/j.fuel.2020.119453 ↗
23. Sun, Z., Cui, M., Ye, C., Yang, S., Li, X., Hung, D., and Xu, M., Split Injection Flash Boiling Spray for High Efficiency and Low Emissions in a GDI Engine under Lean Combustion Condition, Proc. Combust. Inst., vol. 38, no. 4, pp. 5769-5779, 2021c.10.1016/j.proci.2020.05.037 ↗
24. Wang, C., Wang, Y., Zhu, J., Long, W., and Nishida, K., Design and Application of an Algorithm for Measuring Particle Velocity Based on Multiple Characteristics of a Particle, Fuel, vol. 271, p. 117605, 2020.
25. Wu, S., Xu, M., Hung, D.L., and Pan, H., Effects of Nozzle Configuration on Internal Flow and Primary Jet Breakup of Flash Boiling Fuel Sprays, Int. J. Heat Mass Transf., vol. 110, pp. 730-738, 2017.10.1016/j.ijheatmasstransfer.2017.03.073 ↗
26. Xu, M., Zhang, Y., Zeng, W., Zhang, G., and Zhang, M., Flash Boiling: Easy and Better Way to Generate Ideal Sprays than the High Injection Pressure, SAE Int. J. Fuels Lubricants, vol. 6, no. 1, pp. 137-148, 2013.10.4271/2013-01-1614 ↗
27. Yan, J., Gao, S., Liu, W., Chen, T., Lee, T.H., and Lee, C.F., Experimental Study of Flash Boiling Spray with Isooctane, Hexane, Ethanol and Their Binary Mixtures, Fuel, vol. 292, p. 120415, 2021.
28. Yang, J., Dong, X., Wu, Q., and Xu, M., Influence of Flash Boiling Spray on the Combustion Characteristics of a Spark-Ignition Direct-Injection Optical Engine under Cold Start, Combust. Flame, vol. 188, pp. 66-76, 2018.10.1016/j.combustflame.2017.09.019 ↗
29. Zeng, W., Xu, M., Zhang, M., Zhang, Y., and Cleary, D.J., Macroscopic Characteristics for Direct-Injection Multi-Hole Sprays Using Dimensionless Analysis, Exp. Therm. Fluid Sci., vol. 40, pp. 81-92, 2012a.10.1016/j.expthermflusci.2012.02.003 ↗
30. Zeng, W., Xu, M., Zhang, G., Zhang, Y., and Cleary, D.J., Atomization and Vaporization for Flash-Boiling Multi-Hole Sprays with Alcohol Fuels, Fuel, vol. 95, pp. 287-297, 2012b.10.1016/j.fuel.2011.08.048 ↗
31. Zhang, G., and Hung, D.L., Temporal Investigations of Transient Fuel Spray Characteristics from a Multi-Hole Injector Using Dimensionless Analysis, Exp. Therm. Fluid Sci., vol. 66, pp. 150-159, 2015.10.1016/j.expthermflusci.2015.03.011 ↗