NUMERICAL STUDY OF DIRECT INJECTION SPRAY BEHAVIOR OF GASOLINE AND METHANOL-GASOLINE BLENDS UNDER SPLIT-INJECTION STRATEGY IN ENGINE-LIKE CONDITIONS
Source abstract
Abstract
Several studies have shown that the split-injection strategy has improved the shortcomings of the high particulate matter emissions and cycle-to-cycle variations in homogeneous and stratified combustion modes of gasoline direct injection (GDI) engines. However, the spray behavior under the split injection strategy is poorly understood. This study uses computational fluid dynamics (CFD) simulations in Converge software to investigate the spray characteristics of gasoline and methanol-gasoline blends under a split-injection strategy. The simulation studies were performed for a multihole GDI injector in a constant volume spray chamber, replicating the ambient conditions similar to a GDI engine's homogeneous and stratified combustion modes. Appropriate models for simulating different spray phenomena, such as spray breakup, collision, and coalescence, were used. The CFD model was validated using the experimental spray penetration length provided in the engine combustion network database. The results showed that the split-injection reduced the Sauter mean diameter (SMD) of fuel spray droplets and liquid fuel mass content than a single injection case. The dwell time of 2 ms was found suitable for homogeneous mode conditions, while its effect was insignificant in stratified mode conditions. Further, a split ratio of 80:20 resulted in smaller SMD during the injection period and a higher fuel evaporation rate. The effect of methanol addition was also explored under the split-injection mode. M85 showed higher deviations in the liquid spray penetration, SMD, and liquid spray mass content than G100.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Combustion Engine Technologies · Combustion and flame dynamics · Vehicle emissions and performance
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Abu-Zaid,M., Badran, O., and Yamin, J., Effect ofMethanol Addition on the Performance of Spark Ignition Engines, Energy Fuels, vol. 18, no. 2, pp. 312-315, 2004. DOI: 10.1021/ef030103d10.1021/ef030103d ↗
2. Allocca, L., Bartolucci, L., Cordiner, S., Lazzaro, M., Montanaro, A., Mulone, V., and Rocco, V., ECN Spray G Injector: Assessment of Numerical Modelling Accuracy, SAE Tech. Rep. No. 2018-01-0306, 2018. DOI: 10.4271/2018-01-030610.4271/2018-01-0306 ↗
3. Blair, G.P., Design and Simulation of Two-Stroke Engines, Warrendale, PA: Society of Automotive Engineers, 1996.10.4271/R-161 ↗
4. Bonandrini, G., Di Gioia, R., Papaleo, D., and Venturoli, L., Numerical Study on Multiple Injection Strategies in DISI Engines for Particulate Emission Control, SAE Tech. Rep. No. 2012-01-0400, 2012. DOI: 10.4271/2012-01-040010.4271/2012-01-0400 ↗
5. Chapman, L., Transport and Climate Change: A Review, J. Transp. Geog., vol. 15, no. 5, pp. 354-367, 2007. DOI: 10.1016/j.jtrangeo.2006.11.00810.1016/j.jtrangeo.2006.11.008 ↗
6. Engine Combustion Network webpage, accessed June 6, 2023, from https://ecn.sandia.gov/, 2023.
7. Gravalos, I., Moshou, D., Gialamas, T., Xyradakis, P., Kateris, D., and Tsiropoulos, Z., Performance and Emission Characteristics of Spark Ignition Engine Fueled with Ethanol and Methanol Gasoline Blended Fuels, in Alternative Fuel, M. Manzanera, Ed., Intechopen, pp. 155-174, 2011.10.5772/23176 ↗
8. Guo, H., Ding, H., Li, Y., Ma, X., Wang, Z., Xu, H., and Wang, J., Comparison of Spray Collapses at Elevated Ambient Pressure and Flash Boiling Conditions Using Multi-Hole Gasoline Direct Injector, Fuel, vol. 199, pp. 125-134, 2017. DOI: 10.1016/j.fuel.2017.02.07110.1016/j.fuel.2017.02.071 ↗
9. Hwang, J.,Weiss, L., Karathanassis, I.K., Koukouvinis, P., Pickett, L.M., and Skeen, S.A., Spatio-Temporal Identification of Plume Dynamics by 3D Computed Tomography Using Engine Combustion Network Spray G Injector and Various Fuels, Fuel, vol. 280, p. 118359, 2020. DOI: 10.1016/j.fuel.2020.11835910.1016/j.fuel.2020.118359 ↗
10. Itani, L.M., Bruneaux,G., Di Lella, A., and Schulz, C., Two-Tracer LIF Imaging of Preferential Evaporation of Multi-Component Gasoline Fuel Sprays under Engine Conditions, Proc. Combust. Inst., vol. 35, no. 3, pp. 2915-2922, 2015. DOI: 10.1016/j.proci.2014.06.10810.1016/j.proci.2014.06.108 ↗
11. Kale, R. and Banerjee, R., Experimental Investigation on GDI Spray Behaviour of Iso-Octane and Alcohols at Elevated Pressure and Temperature Conditions, Fuel, vol. 236, pp. 1-12, 2019. DOI: 10.1016/j.fuel.2018.08.15310.1016/j.fuel.2018.08.153 ↗
12. Kalwar, A., Chintagunti, S., and Agarwal, A.K., Gasohol Sprays Simulations of a Multi-Hole GDI Injector in Engine-Like Conditions, SAE Tech. Rep. No. 2021-01-0549, 2021. DOI: 10.4271/2021-01-054910.4271/2021-01-0549 ↗
13. Kalwar, A., Singh, A.P., and Agarwal, A.K., Utilisation of Primary Alcohols in Dual-Fuel Injection Mode in a Gasoline Direct Injection Engine, Fuel, vol. 276, p. 118068, 2020. DOI: 10.1016/j.fuel.2020.11806810.1016/j.fuel.2020.118068 ↗
14. Kuwahara, K., Ueda, K., and Ando, H., Mixing Control Strategy for Engine Performance Improvement in a Gasoline Direct Injection Engine, SAE Trans., vol. 107, pp. 267-277, 1998.10.4271/980158 ↗
15. Lee, S. and Park, S., Experimental Study on Spray Breakup and Atomisation Processes from GDI Injector Using High Injection Pressure Up to 30 MPa, Int. J. Heat Fluid Flow, vol. 45, pp. 14-22, 2014. DOI:10.1016/j.ijheatfluidflow.2013.11.00510.1016/j.ijheatfluidflow.2013.11.005 ↗
16. Li, T., Moon, S., Sato, K., and Yokohata, H., A Comprehensive Study on the Factors Affecting Near-Nozzle Spray Dynamics of Multi-Hole GDI Injectors, Fuel, vol. 190, pp. 292-302, 2017. DOI:10.1016/j.fuel.2016.11.00910.1016/j.fuel.2016.11.009 ↗
17. Marseglia, G., Costa, M., Catapano, F., Sementa, P., and Vaglieco, B.M., Study about the Link between Injection Strategy and Knock Onset in an Optically Accessible Multi-Cylinder GDI Engine, Energy Convers. Manag., vol. 134, pp. 1-19, 2017. DOI: 10.1016/j.enconman.2016.12.01210.1016/j.enconman.2016.12.012 ↗
18. Muddapur, A., Jose, J.V., Sahu, S., and Sundararajan, T., Spray Dynamics and Evaporation in a Multi-Hole GDI Injector for Pulsatile and Split Injection at Elevated Ambient Pressure and Temperature Conditions, Fuel, vol. 279, p. 118057, 2020. DOI: 10.1016/j.fuel.2020.11805710.1016/j.fuel.2020.118057 ↗
19. Paredi, D., Lucchini, T., D'Errico, G., Onorati, A., Pickett, L., and Lacey, J., Validation of a Comprehensive Computational Fluid Dynamics Methodology to Predict the Direct Injection Process of Gasoline Sprays Using Spray G Experimental Data, Int. J. Engine Res., vol. 21, no. 1, pp. 199-216, 2020. DOI:10.1177/146808741986802010.1177/1468087419868020 ↗
20. Paredi, D., Lucchini, T., D'Errico, G., Onorati, A., Montanaro, A., Allocca, L., and Ianniello, R., Combined Experimental and Numerical Investigation of the ECN Spray G under Different Engine-Like Conditions, SAE Tech. Rep. No. 2018-01-0281, 2018. DOI: 10.4271/2018-01-028110.4271/2018-01-0281 ↗
21. Parrish, S.E. and Zink, R.J., Development and Application of Imaging System to Evaluate Liquid and Vapour Envelopes of Multi-Hole Gasoline Fuel Injector Spray under Engine-Like Conditions, Atomization Sprays, vol. 22, no. 8, pp. 647-661, 2012. DOI: 10.1615/AtomizSpr.201200621510.1615/AtomizSpr.2012006215 ↗
22. Payri, R., Gimeno, J., Marti-Aldaravi, P., and Vaquerizo, D., Internal Flow Characterisation on an ECN GDi Injector, Atomization Sprays, vol. 26, no. 9, pp. 889-919, 2016. DOI: 10.1615/AtomizSpr.201501393010.1615/AtomizSpr.2015013930 ↗
23. Qian, Y., Li, Z., Yu, L., Wang, X., and Lu, X., Review of the State-of-the-Art of Particulate Matter Emissions from Modern Gasoline-Fueled Engines, Appl. Energy, vol. 238, pp. 1269-1298, 2019. DOI:10.1016/j.apenergy.2019.01.17910.1016/j.apenergy.2019.01.179 ↗
24. Sementa, P., Vaglieco, B.M., and Catapano, F., Thermodynamic and Optical Characterisations of a High-Performance GDI Engine Operating in Homogeneous and Stratified Charge Mixture Conditions Fueled with Gasoline and Bio-Ethanol, Fuel, vol. 96, pp. 204-219, 2012. DOI: 10.1016/j.fuel.2011.12.06810.1016/j.fuel.2011.12.068 ↗
25. Senecal, P.K., Pomraning, E., Richards, K.J., and Som, S., Grid-Convergent Spray Models for Internal Combustion Engine Computational Fluid Dynamics Simulations, J. Energy Resour. Technol., vol. 136, no. 1, p. 012204, 2014. DOI: 10.1115/1.402486110.1115/1.4024861 ↗
26. Sharma, N. and Agarwal, A.K., Microscopic and Macroscopic Spray Characteristics of GDI Injector Using Gasohol Fuels at Various Injection Pressures, SAE Tech. Rep. No. 2016-01-0868, 2016. DOI:10.4271/2016-01-086810.4271/2016-01-0868 ↗
27. Sphicas, P., Pickett, L.M., Skeen, S., Frank, J., Lucchini, T., Sinoir, D., and Som, S., A Comparison of Experimental and Modelled Velocity in Gasoline Direct-Injection Sprays with Plume Interaction and Collapse, SAE Int. J. Fuels Lub., vol. 10, no. 1, pp. 184-201, 2017.10.4271/2017-01-0837 ↗
28. Tian, J., Zhao, M., Long, W., Nishida, K., Fujikawa, T., and Zhang, W., Experimental Study on Spray Characteristics under Ultra-High Injection Pressure for DISI Engines, Fuel, vol. 186, pp. 365-374, 2016. DOI: 10.1016/j.fuel.2016.08.08610.1016/j.fuel.2016.08.086 ↗
29. Wang, Z., Jiang, C., Xu, H., Badawy, T.,Wang, B., and Jiang, Y., The Influence of Flash Boiling Conditions on Spray Characteristics with Closely Coupled Split Injection Strategy, Appl. Energy, vol. 187, pp. 523-533, 2017. DOI: 10.1016/j.apenergy.2016.11.08910.1016/j.apenergy.2016.11.089 ↗
30. Wang, Z., Ma, X., Jiang, Y., Li, Y., and Xu, H., Influence of Deposit on Spray Behaviour under Flash Boiling Condition with the Application of Closely Coupled Split Injection Strategy, Fuel, vol. 190, pp. 67-78, 2017. DOI: 10.1016/j.fuel.2016.11.01210.1016/j.fuel.2016.11.012 ↗
31. Wang, Z., Xu, Y., andWang, J., Suppression of Super-Knock in TC-GDI Engine Using Two-Stage Injection in Intake Stroke (TSII), Sci. China Technol. Sci., vol. 57, no. 1, pp. 80-85, 2014. DOI: 10.1007/s11431-013-5374-310.1007/s11431-013-5374-3 ↗
32. Yang, J. and Anderson, R.W., Fuel Injection Strategies to Increase Full-Load Torque Output of a Direct-Injection SI Engine, SAE Trans., vol. 107, pp. 498-505, 1998.10.4271/980495 ↗
33. Zhang, J., Yao, S., Patel, H., and Fang, T., An Experimental Study on Gasoline Direct-Injection Spray and Atomization Characteristics of Alcohol Fuels and Iso-Octane, Atomization Sprays, vol. 21, no. 5, pp. 363-374, 2011. DOI: 10.1615/AtomizSpr.201100362410.1615/AtomizSpr.2011003624 ↗
34. Zhang, Z., Zhang,W.,Ma, X., Awad, O.I., Xu, H., and Shuai, S., Effects of GDI Injector Deposits on Spray and Combustion Characteristics under Different Injection Conditions, Fuel, vol. 278, p. 118094, 2020. DOI: 10.1016/j.fuel.2020.11809410.1016/j.fuel.2020.118094 ↗