ESTIMATION OF THE SPECIFIC KINETIC ENERGY INCREASE FOR LIQUID JET BREAKUP IN AIR CROSSFLOW
Source abstract
Abstract
The influence of liquid characteristics on the breakup behavior of a liquid jet in an air crossflow was investigated. Air flowed through a rectangular duct, and liquid flow was introduced vertically. Three Newtonian fluids (9, 36, and 72 wt% glycerol mixtures) and one shear-thinning fluid [0.1 wt% carboxymethylcellulose solution (CMC)] were used. The flow behavior of these liquids was visualized, and the air velocity in the duct was measured. For Newtonian fluids, the liquid jet curved, leading to a reduction in Reynolds number and an increase in Ohnesorge number. In contrast, the CMC liquid column extended downstream without breaking up, maintaining a thin flow without surface waves. This behavior was attributed to a reduction in surface viscosity caused by airflow-induced shear effects. The specific kinetic energy increase (SKEI) provided by airflow was calculated to evaluate the breakup energy, revealing that CMC required greater energy for breakup compared with Newtonian fluids. The Newtonian fluid breaks up more easily-that is, a greater breakup energy is required to break up the liquid column of CMC. Additionally, as the velocity of air increased, SKEIbeakup decreased slightly. These results demonstrate that the methodology is effective for evaluating liquid jet breakup behavior and provides quantitative insights into the influence of fluid characteristics in crossflow phenomena.
Source: openalex_inverted_index · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fluid Dynamics and Heat Transfer · Rocket and propulsion systems research · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Akafuah, N.K., Salazar, A.J., and Saito, K., Estimation of Liquid Volume Fraction and Droplet Number Density in Automotive Paint Spray Using Infrared Thermography-Based Visualization Technique, Atom. Sprays, vol. 19, no. 9, pp. 847-861, 2009.10.1615/AtomizSpr.v19.i9.30 ↗
2. Broumand, M. and Birouk, M., Effect of Nozzle-Exit Conditions on the Near-Field Characteristics of a Transverse Liquid Jet in a Subsonic Uniform Cross Airflow, Phys. Fluids, vol. 29, no. 11, p. 113303, 2017.10.1063/1.4994978 ↗
3. Colbert, S.A. and Cairncross, R.A., A Computer Simulation for Predicting Electrostatic Spray Coating Patterns, Powder Technol., vol. 151, nos. 1-3, pp. 77-86, 2005.10.1016/j.powtec.2004.11.039 ↗
4. Colbert, S.A. and Cairncross, R.A., A Discrete Droplet Transport Model for Predicting Spray Coating Patterns of an Electrostatic Rotary Atomizer, J. Electrostat., vol. 64, nos. 3-4, pp. 234-246, 2006.10.1016/j.elstat.2005.06.003 ↗
5. Darwish Ahmad, A., Abubaker, A.M., Salaimeh, A.A., and Akafuah, N.K., Schlieren Visualization of Shaping Air during Operation of an Electrostatic Rotary Bell Sprayer: Impact of Shaping Air on Droplet Atomization and Transport, Coatings, vol. 8, no. 8, p. 279, 2018.10.3390/coatings8080279 ↗
6. Domnick, J., Scheibe, A., and Ye, Q., The Simulation of the Electrostatic Spray Painting Process with High-Speed Rotary Bell Atomizers. Part I: Direct Charging, Part. Part. Syst. Charact., vol. 22, no. 2, pp. 141-150, 2005.10.1002/ppsc.200400968 ↗
7. Ellwood, K.R.J. and Braslaw, J., A Finite-Element Model for an Electrostatic Bell Sprayer, J. Electrostat., vol. 45, no. 1, pp. 1-23, 1998.10.1016/S0304-3886(98)00011-4 ↗
8. Harris, J., A Note on the Generalized Reynolds Number in Non-Newtonian Flow, Brit. J. Appl. Phys., vol. 14, no. 11, pp. 817-818, 1963.10.1088/0508-3443/14/11/421 ↗
9. Hatayama, Y., Haneda, T., Shirota, M., Inamura, T., Daikoku, M., Soma, T., Saito, Y., and Aoki, H., Formation and Breakup of Ligaments from a High Speed Rotary Bell Cup Atomizer (Part 1: Observation and Quantitative Evaluation of Formation and Breakup of Ligaments), Trans. Jpn. Soc. Mech. Eng. Part B, vol. 79, no. 802, pp. 1081-1094, 2013.10.1299/kikaib.79.1081 ↗
10. Im, K.S., Lai, M.C., Liu, Y., Sankagiri, N., Loch, T., and Nivi, H., Visualization and Measurement of Automotive Electrostatic Rotary-Bell Paint Spray Transfer Processes, J. Fluids Eng. Trans. ASME, vol. 123, no. 2, pp. 237-245, 2001.10.1115/1.1359210 ↗
11. Im, K.S., Lai, M.C., Yu, S.T.J., and Matheson, R.R., Simulation of Spray Transfer Processes in Electrostatic Rotary Bell Sprayer, J. Fluids Eng. Trans. ASME, vol. 126, no. 3, pp. 449-456, 2004.10.1115/1.1758263 ↗
12. Inamura, T., Nagai, N., Hirai, T., and Asano, H., Disintegration Phenomena of Metallized Slurry Fuel Jets in High Speed Air Stream, ICLASS-91; Proc. of the Fifth Int. Conf. on Liquid Atomization and Spray Systems, Gaithersburd, MD, pp. 839-846, 1991.
13. Jiao, D., Jiao, K., Zhang, F., Bai, F., and Du, Q., Primary Breakup of Power-Law Biofuel Sprays in Pressurized Gaseous Crossflow, Fuel, vol. 258, p. 116061, 2019.10.1016/j.fuel.2019.116061 ↗
14. Leask, S.B., McDonell, V.G., and Samuelsen, S., Critical Evaluation of Momentum Flux Ratio Relative to a Liquid Jet in Crossflow, Atom. Sprays, vol. 28, no. 7, pp. 599-620, 2018.10.1615/AtomizSpr.2018027032 ↗
15. Mazallon, J., Dai, Z., and Faeth, G.M., Primary Breakup of Nonturbulent Round Liquid Jets in Gas Crossflows, Atom. Sprays, vol. 9, no. 3, pp. 291-311, 1999.10.1615/AtomizSpr.v9.i3.40 ↗
16. Metzner, A.B. and Otto, R.E., Agitation of Non-Newtonian Fluids, AIChE J., vol. 3, no. 1, pp. 3-10, 1957.10.1002/aic.690030103 ↗
17. Ogasawara, S., Daikoku, M., Shirota, M., Inamura, T., Saito, Y., Yasumura, K., Shoji, M., Aoki, H., and Miura, T., Liquid Atomization Using a Rotary Bell Cup Atomizer (Influence of Flow Characteristics of Liquid on Breakup Pattern), J. Fluid Sci. Technol., vol. 5, no. 3, pp. 464-474, 2010.10.1299/jfst.5.464 ↗
18. Qian, L., Zhong, X., Zhu, C., and Lin, J., An Experimental Investigation on the Secondary Breakup of Carboxymethyl Cellulose Droplets, Int. J. Multiph. Flow, vol. 136, p. 103526, 2021.10.1016/j.ijmultiphaseflow.2020.103526 ↗
19. Sharma, V., Haward, S.J., Serdy, J., Keshavarz, B., Soderlund, A., Threlfall-Holmes, P., and McKinley, G.H., The Rheology of Aqueous Solutions of Ethyl Hydroxy-Ethyl Cellulose (EHEC) and Its Hydrophobically Modified Analogue (HmEHEC): Extensional Flow Response in Capillary Break-Up, Jetting (ROJER) and in a Cross-Slot Extensional Rheometer, Soft Matter, vol. 11, no. 16, pp. 3251-3270, 2015.10.1039/C4SM01661K ↗
20. Shen, B., Ye, Q., Guettler, N., Tiedje, O., and Domnick, J., Primary Breakup of a Non-Newtonian Liquid Using a High-Speed Rotary Bell Atomizer for Spray-Painting Processes, J. Coat. Technol. Res., vol. 16, no. 6, pp. 1581-1596, 2019.10.1007/s11998-019-00231-4 ↗
21. Shirota, M., Kato, M., and Ishio, A., Rim Breakups of Impacting Drops on a Superhydrophobic Surface and a Superheated Surface, Fluids, vol. 7, no. 2, p. 79, 2022.10.3390/fluids7020079 ↗
22. Tachi, K., Yamada, K., Okuda, C., and Suzuki, S., Effect of Rotating Cup Shapes and Spray Conditions on Paint Atomization, J. Jpn. Soc. Colour Mater., vol. 58, no. 7, pp. 390-401, 1985.10.4011/shikizai1937.58.390 ↗
23. Wu, P.K., Kirkendall, K.A., Fuller, R.P., and Nejad, A.S., Breakup Processes of Liquid Jets in Subsonic Crossflows, J. Propuls. Power, vol. 13, no. 1, pp. 64-73, 1997.10.2514/2.5151 ↗
24. Xia, Y., Khezzar, L., Hardalupas, Y., and Alshehhi, M., Influence of Energy Exchange between Air and Liquid Streams on Spray Characteristics and Atomization Efficiency of Water-Air Impinging Jets, Atom. Sprays, vol. 29, no. 8, pp. 677-707, 2019.10.1615/AtomizSpr.2020031425 ↗